Hindustan Urvarak and Rasayan Limited - Jharkhand

34163378 supply and installation of low voltage switchboard at hurl sindri project supply and installation of low voltage switchboard at hurl sindri project , supply, loading, handling, storage, transportation within site, erection, installation, testing and commissioning etc. of following lt panel , 415 v, 3 ph. & n, ip54, floor mounted sheet steel enclosed main power board with al bus bar of 250a which consists of 2 nos. incoming 4p, 250 a, 50ka mccb incomer with earthfault, overcurrent protection and mechanical interlock with 250 / 1 ct, mfm, voltmeter, vss & ryb indications & 8nos. 63 a tpn rccb outgoing feeders indications & 7 nos. 63 a tpn sfu outgoing feeders on indoor bus & 2 nos. 4p, 100a, 30ka mccb outgoing feeders on outdoor bus with timer controlled feeders with suitable power contactor to operate outdoor bus. , 415 v, 3 ph. & n, ip55, outdoor type, structural mounted, weatherproof ( ip 55 ) lighting distribution board type db with bus bar 200 a, 415v having 2 nos. tpn, incomer 3p, 100a, 30kamccb withvoltmeter, vss & ryb indications and6 nos. 63 a tpn rccboutgoing feeder circuit and 16a, dp mcb, 6nos. , 415 v, 3 ph. & n, ip54, floor mounted sheet steel enclosed main power board with al bus bar of 400a which consists of 2 nos. incoming [ 4p, 400a, 50ka mccb incomer and 4p, 250a, 50ka mccb ] incomer with earthfault, overcurrent protection and mechanical interlock with 400 / 1 ct& 250 / 1 ct, mfm, voltmeter, vss & ryb indications &10 nos. 100 a mccb outgoing feeders & 4 nos. 63 a tpn rccb outgoing feeders& 2nos. 3p, 36a sfuoutgoing feeders and 16a, dp mcb, 6nos. , 415 v, 3 ph. & n, ip54, floor mounted sheet steel enclosed main power board with al bus bar of 100a which consists of 2 nos. incoming 4p, 100 a, 30ka mccb incomerwith earthfault, overcurrent protection and mechanical interlock with 100 / 1 ct, mfm, voltmeter, vss & ryb indications & 63 a tpn rccb outgoing feeders& 2 nos. 3p, 63a sfuoutgoing feeders and 32a, dp mcb, 6nos. , 415 v, 3 ph. & n, ip54, floor mounted sheet steel enclosed main power board with al bus bar of 630a which consists of 2 nos. incoming 4p, 630 a, 50ka mccb incomer with earthfault, overcurrent protection and mechanical interlock with 630 / 1 ct, mfm, voltmeter, vss & ryb indications & 10 nos. 63 a tpn rccb outgoing feeders indications & 6 nos. 250 a tpn sfu outgoing feeders & 2 nos. 3p, 63a sfuoutgoing feeders and 32a, dp mcb, 6nos....

Uranium Corporation Of India Limited - Jharkhand

33697571 spares of 55 kw nflp gate end box spares of 55 kw nflp gate end box , spares of 55 kw nflp gate end box , pr pilot relay with base , heavy duty screw assy. complete with handle, bush, lock etc for 200 amps plug socket , dmc moulded plug insulation ( w.o.pin ) for 200 amps plug & socket , brass pin for plug ( set of 4 pins ) of 200 amps plug & socket , dmc moulded socket insulation ( w.o.pins ) for 200 amps plug & socket , brass pin for socket ( set of 4 pins ) of 200 amps plug & socket , 72 sq.mm ammeterrange : 0 300 900a ( w.o.ct ) , inter lock assy for isolator handle , auxiliary contactor 3no+1nc with 110v coil type ca2 dn1319 fitted with add on block la1d11 , 72 sq.mm voltmeter range: 0 500ac , contactor type tcla1 d22 with auxiliary contact 2no+2nc coil voltage 440v ac , metallic togle switch complete with chacker nut of any reputed make 2 way 10a 440v , earth leakage relay 50ma to 750ma with time delay 0.1sec to 1sec auxiliary voltage 12v ac , 200 amps plug and socket complete set with leads for socket , 200 amps socket complete set with ieads , single phase preventer aux. supply voltage 440v type vsp3 make : minilec , control transformer primary voltage 0 to 415v 440v 460v / secondary 0 to 8v 12v and 0 to 110v va 100va , limit switch for isolator , led indicating lampoperating voltage : 12v ac colour : red , led indicating lamp operating voltage : 12v ac colour: green , led indicating lamp operating voltage : 12v ac colour : yellow...

Central Coalfields Limited - Jharkhand

33566712 bids are invited for procurement of spares for electroteknica 1 nvcbv0001 shunt trip coil assembly 2 2 nvcbv0004 breaker charging handle 2 3 nvcbv0013 vacuum interrupter 1 4 nvcbv0014 96sq.mm ammeter upto 0 600 / 120a, ctr 600 / 5a 1 5 nvcbv0015 96sq.mm ammeter upto 0 300 / 600a, ctr 300 / 5a 1 6 nvcbv0017 96sq.mm voltmeter 0 5ka, ptr3.3kv / 110v ac 2 7 nvcbi0018 ammeter selector switch 2 8 nvcbi0019 voltmeter selectoe switch 2 9 nvcbi0020 mushroom head push button 2 10 nvcbp0032 tnc switch for elec.operated vcb 2 11 nvcbp0034 rectifier capacity unit 15a 2 12 nvcbp0035 earth leakage relay 1 13 nvcbp0037 3.3 kv / 110v12v, 100va / ph 3 ph pt 2 14 nvcbp0044 3.3 kv, 3 amps. p.t fuse 6 15 nvcbp0057 hrc fuse link 10 amps. 6 16 nvcbp0074 limit switch 2 17 ivb0001 shunt trip / series trip coil 2 18 ivb0003 auxillary switch assembly 1 19 ivb0021 breaker charging mechnism 2 20 ivb0022 catch mechanism 2 21 ivb0059 tpnd o / c & e / f relay with high set 2 22 ivb0040 11kv / 110v, 100va per phase 3 phase p.t 2 23 ivb0041 resin cast c.t class 5p 10 / class 1.0 3 24 ivb0068 master tripping relay 1 total quantity : 51...

South Eastern Railways - Jharkhand

33178939 supply of starter for 5hp submersible pump with ammeter, voltmeter etc.starter for 5hp submersible pump with ammeter, voltmeter etc., starter for 5hp submersible pump with ammeter, voltmeter, single phase preventer, indicating lights and dry run protection unit ( make l&t ) make bch or l&t or greaves or equivalent....

Welfare Department - Jharkhand

33028328 bids are invited for measuring steel tape , combination plier insulated , screw driver insulated , electrician screw driver thin stem insulated handle , heavy duty screw driver insulated , electrician screw driver thin stem insulated handle , punch centre , knife double bladed electrician , neon tester , steel rule graduated both in metric and english unit , hammer, cross peen with handle , hammer, ball peen with handle , pincer , c clamp , spanner adjustable drop forged, ss , blow lamp brass , chisel cold , chisel firmer with wooden handle , allen key alloy steel , grease gun , bradawl , pully puller with 3 legs , bearing puller inside and outside , pipe vice cast iron with hardened jaw open type , scissors blade, ss , crimping tool , wire cutter and stripper , mallet hard wood , hammer extractor type , hacksaw frame , try square , outside calliper , inside calliper , divider , pliers long nose insulated , pliers flat nose insulated , pliers round nose insulated , tweezers , snip straight and bent heavy duty , de metric spanner double ended , drill hand brace , drill ss twist block , plane cutters , smoothing cutters , gauge wire imperial stainlees steel marked in swg and mm , file flat , file half round , file round , file flat rough , file flat bastard , file flat smooth , file rasp, half round , copper bit soldering iron , de soldering gun , hand vice , table vice , oil can , contactor and auxiliary contacts , limit switch , rotary switch , relay a cut out relays b reverse current c over current d under voltage , pin, shackle, egg and suspension type insulators , hydrometer , hand drill machine , portable electric drill machine , load bank lamp or heater type , brake test arrangement with two spring balance rating , laboratory type induction coil , out side micrometer , thermometer digital , series test lamp , knife switch dpdt fitted with fuse terminals , knife switch tpdt fitted with fuse terminals , miniature breaker , earth plate , earth electrode , mccb , elcb and rccb , fuses , rheostat sliding type , various electronics components , capacitors , various lamps , plug socket piano switch lamp holder , cables twisted pair nonmetallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multiconductor cable coaxial cable directburied cable , bus bar with brackets coaxial cable directburied cable , bus bar with brackets , rubber mat , electrician helmet , rcc pole with accessories ms angle iron, c clamp, stay insulator etc and materials , safety belt , ohm meter series type and shunt type , digital multi meter , ac voltmeter mi analog, portable box type housed in bakelite case , milli voltmeter centre zero analog, portable box type housed in bakelite case , ammeter mc analog, portable box type housed in bakelite case , ac ammeter mi, analog, portable box type housed in bakelite case , kilo wattmeter analog , digital wattmeter , ac energy meter , power factor meter digital , frequency meter , magnetic flux meter , lux meter , tachometer , tong tester clamp meter , megger , 3 point dc starter , 4 point dc starter , wheat stone bridge with galvanometer and battery , single phase variable auto transformer , phase sequence indicator , growler , ac starters resistance, dol, manual star delta, semi star delta, fully star delta, soft, auto transformer starter , oscilloscope dual trace , function generator , soldering iron , temperature controlled soldering iron , discrete component trainer , linear ic trainer , digital ic trainer , a electric induction plate , b electric kettle , c electric iron , d immersion heater , e ac ceiling fan and ac table fan , f geyser storage type , g mixture and grinder , h washing machine semi automatic , i motor pump set , oil testing kit , inverter with battery , voltage stabilizer , dc power supply , battery charger , current transformer , potential transformer , solar panel with battery , pentium iv computer or latest , ink jet laser printer , dc shunt generator with control panel , motorgenerator ac to dc , dc compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker , dc series motor coupled with spring balance load , dc shunt motor , dc compound motor with starter and switch , motor generator dc to ac set , ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load , ac phasewound slip ring motor with starter switch , universal motor with starterswitch , synchronous motor with accessories like starter, excitation arrangements , thyristor igbt controlled dc motor drive with tachogenerator feedback arrangement , thyristorigbt controlled ac motor drive with , single phase transformer, core type, air cooled , three phase transformer, shell type oil cooled with delta star , electrical machine trainer , used dc generatorsseries, shunt and compound type for overhauling practice , pillar electric drill machine motorized , motorised bench grinder , ac series type motor , single phase capacitor motor with starter switch , manual motor coil winding machine , ceiling fan coil winding machine , primary current injection set , stepper motor with digital controller , shaded pole motor , working bench , wiring board , black boardwhite board , fire extinguisher co2 , fire buckets , diesel generator set with change over switch, over current breaker and water aircooled with armature, stardelta connections ac 3 phase , metal rack , locker with drawer...

Drinking Water And Sanitation Department - Jharkhand

32694711 supplying, installation, testing and commissioning submersible pump set for rural water supply scheme manushmudya, pumping plant. under d.w and s mechanical division, jamshedpur 1 supply of submersible pump set suitable for 6 dia bore well running with 3 phase415± 10% volts50 c / s 2900 rpm having discharging capacity 2600 gph against total head of 60 meters with noryl / g.m impeller consists of following accessories ( a ) 2½ dia g.i column pipe 200 ( 10 long both end threaded one end fitted socket and other end covered by plastic ) ( b ) 3 core flat copper cable 4 mm² 1 coil ( c ) m.s clamp 2½ dia 2 pairs ( d ) c.i.d.f sluice valve 2½dia 1no. ( e ) ) c.i.d.freflexvalve 2½dia 1no. 2 supplying and fitting cubical type duly painted control panel boardconsisting 32 amps. tpn mccb inbuilt single phase preventor and suitable forstar delta automatic starter water level guard with suitable length and size of wire phase indicating bulb in three different colour suitable voltmeter and ampere meterwith selector switch make l&t / havell;s 3 chemical earthing3 metersand80 mm hole size with electrode and chemical compound etc. with watering pipe and locking arrangement including soldering, riveting, jointing g.i flat 50 mm x 6 mm to all equipments. 4 supplyingtriple spur gear type 3 tonne capacitychain pulley block suitable for capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per is 3832 carrying isi mark. 5 renovation of light wiring inside & out side pump chamber by doing short point light wiring 4 point long point light wiring 4 points, 150 watt led street light complete set 2 nos., 36 watt cfl 4 nos. etc. all including labour charges all complete 6 supplying and making tripod ( 14x 65 mm c.i pipe ) hanging chain pulley block 7 supplyingxlpe / pvc insulated, armoured cable 1100 v grade with isi mark 25 mm² x 3½ core, solid / stranded copper conductor with 6 mm thick 25 mm width m.s. spacer with g.i. earth wire 6 sq mm, completein an approved. from transformer to p / house via gangway. 8 supplying installation testing and commissioning of 30 kva servo controlled automatic voltage stabilizer oil cooled power line / ipc / servokon make suitable for output voltage of 415 volt ± 1% under input voltage range of 280 450 volts ( phase to phase ) 3 phase, 50 hz, with copper wound transformer. the stabilizer shall function satisfactory even if incoming supply is unbalanced between phases within range of 10%. the stabilizer should have indicator, alarm, voltmeterand auto / manual selector switch for measuring input and output voltage, raise / low push buttons etc. suitable capacity terminationstrip and bus bars for incoming and outgoing cable should be provided. all three phase shall be independently monitored and corrected. following protections and indications shall be incorporated :over voltage / under voltage single phasing cut off conductor with electronic output sensing unit. 9 supplying and fixing 100 amp. 415± 15% voltage change over switch, havells / l & t make 10 transformer oil for the above stabilizer of best make up to mark. 11 supplying, installation, testing & commissioningof outdoor type 63 kva 11 / 0.433 kva copper wound distribution transformer with off load tap changer 12.5% to 2.5% in step of 2.5%, continuously rated for three phase, 50 hz, full load and temperature rise not exceeding 45 degree centigrade by thermometer in oil and 50 degree centigrade by the resistance in winding after continuous, run atfull load rating, the transformer should have oil immersed winding having vector group of 0.4 / 11, ht side connected in delta & lt side connected in star with neutral brought out connected. the transformer should have power terminal bushing arrangement on ht side & cable box in lt side with standard fitting for mounting of transformer with first filling of transformer oil including all accessories etc. all complete with all materials make – indian transformer / synergy / banglabijulee / kirloskar for ruralwatersupply p / pmanushmudia....

Drinking Water And Sanitation Department - Jharkhand

32639583 government of jharkhand through its public works department ( pwd ) is engaged in framing / revision of schedule of rates and as part of this endeavor, quotations through e tender are invited for replacement of damaged electro mechanical items of ( a ) babhangama rural ( mvs ) water supply scheme, ( b ) sarath rural ( mvs ) water supply scheme and ( c ) kairow rural ( mvs ) water supply scheme ( material supply, installation and commissioning of pump set works pertaining to drinking water supply a babhangama rural ( mvs ) water supply scheme 1 pump & motor : 1.01 supplying, installation, testing and commissioning of electrically driven vertical turbine pump sets kirloskar / wpil / mather & plate / jyoti having discharge capacity of raw water 50 m3 / h against total head of 40 meter, in all concern coupled with vertical hollow shaft sq. cage induction motor make ( kirloskar / crompton / jyoti ) operated on 415 ± 10% volt, 50hz, 1460 rpm ( 10% above the capacity of pump ) with sole plate, discharge head, m.s. d.f. column assembly random length of 5ft, total 50ft s.s. line shaft, s.s. socket, spider bearing with rubber less bush, cidf sluice valve 1no, cidf nr valve 1no, pressure gauge 1no & fixing the discharge new pump to the existing common header etc. complete. motor control panel 100 amp. 2.01 cost towards replacement of old panel by supply, installation & commissioning of new floor mounted motor control panel comprising 100 amp copper bus bar 04 nos. in m.s. steel ( 16swg ) cubical box ( 3’ x 2.5’ x 1’ )  t.p.n. main switch sdf type in ss enclosure make l&t 100 amp 1 no.  three pole mccb ( make l&t ) 63 amp 1 no. for incomer feeder.  three pole mccb ( make l&t ) 32 amp 2 nos. for starter.  fasd starter ( make l&t ) suitable for 15 hp pump set. 02 nos.  ammeter 03 nos. ( 0 50amp ) 01 no., ( 0 30amp ) 02 nos.  voltmeter ( 0 500v ) 1 no. mcp should be comprising with selector switches, phase indicator ( ryb ) , push button ( start & off ) , on off indicator for starter, provision of lighting arrangement ( 25amp mcb ) etc. all complete. for clear water p / plant 2.02 cost towards replacement of old panel by supply, installation & commissioning of new floor mounted motor control panel comprising 100 amp copper bus bar 04 nos. in m.s. steel ( 16swg ) cubical box ( 3’ x 2.5’ x 1’ )  t.p.n. main switch sdf type in ss enclosure make l&t 100 amp 1 no.  three pole mccb ( make l&t ) 100 amp 1 no. for incomer feeder.  three pole mccb ( make l&t ) 63 amp 2 nos. for starter.  fasd starter ( make l&t ) suitable for 15 hp pump set. 02 nos.  ammeter 03 nos. ( 0 50amp ) 01 no., ( 0 30amp ) 02 nos.  voltmeter ( 0 500v ) 1 no. mcp should be comprising with selector switches, phase indicator ( ryb ) , push button ( start & off ) , on off indicator for starter, provision of lighting arrangement ( 25amp mcb ) etc. all complete. for raw water p / plant for raw water p / plant b sarath rural ( mvs ) water supply scheme 1 pump & motor : 1.01 supplying, installation, testing and commissioning of electrically driven horizontal split casing centrifugal pump set make ( kirloskar / wpil / mather & platt / jyoti ) having discharge capacity of clear water 35 m3 / h against total head of 40 meter coupled with tefc sq. cage induction motor make ( kirloskar / crompton / jyoti ) operated on 415 + 10% volts, 50hz, 1440 rpm mounted on common m.s. fabricated base plate with cidf sluice valve 1 no, cidf nr valve 1 no, pressure gauge 1 no, tire coupling 1 no, etc. all complete. 2 motor control panel 100 amp. 2.01 cost towards supplying, fitting & commissioning of motor control panel for operating 2 nos. pump set with fasd starter to operate installed c / f pump set having 63 amp mccb as main incomer, 40 amp mccb as main switch of starters, led indicator, amp meter ( 0 30 amp ) for each pump & volt meter ( 0 500 volt ) selector switch motor control panel should have copper bus bar arrangement. the panel box should be made of swg 18 iron sheet, size 2’ x 1½’ x 1’ with 3 layer pvc paint. all electrical elements should be fitted in iron box. control panel box should be of wall hanging type. kairow rural ( mvs ) water supply scheme pump & motor : supplying, installation, testing and commissioning of electrically driven vertical turbine pump sets kirloskar / wpil / mather & plate / jyoti having discharge capacity of raw water 60 m3 / h against a total head of 45 meter, in all concern coupled with vertical hollow shaft sq. cage induction motor make ( kirloskar / crompton / jyoti ) , operated on 415 ± 10% volt, 50hz, 1460 rpm ( 10% above the capacity of pump ) with sole plate, discharge head, m.s. d.f. column assembly random length of 5ft, total 50ft s.s. line shaft, s.s. socket, spider bearing with rubber cut less bush, cidf sluice valve 1no, cidf nr valve 1no, pressure gauge 1no etc. all complete....

Drinking Water And Sanitation Department - Jharkhand

32583653 complete renovation work with supply installation testing and commissioning of pump sets, motor control panels, cables and its allied works at raw water and clear water pumping plant at multi village rural water supply scheme, pandra 1.a raw water pumping plant: 1.01 cost towards supplying, installation, testing and commissioning of electrically driven horizontal split casing centrifugal pump set make ( kirloskar / wpil / mather & plate / jyoti ) coupled with tefc sq. cage induction motor make ( kirloskar / crompton / jyoti / abb ) operated on 415 + 10% volts, 50hz, 1470 rpm mounted on common m.s. fabricated base plate with 4dia or suitable size of cidf sluice valve 1 no, cidf nr valve 1 no, foot valve 1 no, pressure gauge 1 no, tyre coupling 1 no etc all complete. head 18 m discharge 120 m3 / h ( hp 15 approx ) 1.02 supplying all labour tools and tackles for taking out old and damaged c / f pump set with all accessories , demolition of foundation for installation of new hsc centrifugal pump sets. 1.03 supplying all labour tools and tackles for making new pcc foundation of size 4′ x 2.5 x 2.5′ with all materials such as cement , sand, stone chips, foundation bolt 6 nos etc all complete and plastering and punning over exposed surface with all labour tools, tackles and technician charges. 1.04 cost for supply and laying of suction pipe line with supplying of 5 dia or suitable dia size as per pump at site, heavy duty g.i. pipe 6 m, bend 2 nos., flange 6 nos., nut, bolt, washer 10kg, rubber insertion 5kg etc, cutting of pipe in required size and doing complete welding work including all labour, tools, tackle and technician charges. with cp & ohc. ( rate after deducting the scrap materials. ) 1.05 cost for supply and laying of 4dia delivery pipe line with supplying of 4 dia or suitable dia size as per pump at site, heavy duty g.i. pipe 6m, bend 1 nos., flange 4 nos., nut, bolt, washer 5kg, rubber insertion 5kg etc, cutting of pipe in required size and doing complete welding work including all labour, tools, tackle and technician charges. with cp & ohc. ( rate after deducting the scrap materials. ) 1.06 cost for supplying and laying of 3 core x 10 mm2, pvc insulated and pvc sheathed unarmoured copper cable of 1.1 kv grade. from panel to motor in 2 length each for both motor. with cp and ohc. 1.07 socketing of terminal ends with s / f of terminal socket including all labour , tools and tackles. 3 core x 10 mm2copper cable. 1.08 cost for supplying and laying of 3.5 core x 25 mm2, pvc insulated and pvc sheathed armoured aluminum cable of 1.1 kv grade. from electric pole to panel with cp and ohc. 1.09 socketing of terminal ends with s / f of terminal socket including all labour , tools and tackles. 3.5 core x 25 mm2aluminium cable. 1.10 cost towards supplying, installation, testing and commissioning of tpn main switch / isolator of 100a , make ( havells / schnieder / l&t / any reputed make isi marked. ) . 1.11 providing floor / wall mounted cubical l.t motor control panel fabricated with ms sheet and painted, dust and vermin proof, proper ventilated, consisting of – proper distribution 100 amp copper bus bar 4 pole 1 set micro processor base tpn mccb 100 amp l&t / siemens make with earth fault relay for incoming feeder – 1no. mccb 63 amp tpn type l&t / siemens make for outgoing feeder 3 nos. ( 1no for each pump sets+1 no. as spare ) suitable size of fully automatic star delta starter make l&t / bch / schnider make 3nos. 0 500 v voltmeter with selector switch 3nos ct operated ampere meter ( 0 200a ) with ct 3 sets with selector switch 3 nos, phase indicating neon lamp 9 nos., s.p.p. 3 nos. doing internal wiring with proper gauge of copper wire etc all complete job and testing on load. 1.12 cost for doing chemical earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry with cover plate having locking arrangements and watering pipe 2.7 meter long etc with charcoal / coke and salt as required for chemical earthing. 1.13 supplying and laying of 8 swg copper wire / gi wire for making earthing connection in to from earthing station to panel to motor . 1.14 cost towards doing complete electric wiring inside and outside of pump house with s / f of copper cable, switches, bulb holder, sockets, indicator lamp, led bulb 2, led tube light 1no., 40w led flood light 1no. etc all complete including transportation and electrician charges. 1.b clear water pumping plant: 1.01 cost towards supplying, installation, testing and commissioning of electrically driven horizontal split casing centrifugal pump set make ( kirloskar / wpil / mather & plate / jyoti ) coupled with tefc sq. cage induction motor make ( kirloskar / crompton / jyoti / abb ) operated on 415 + 10% volts, 50hz, 1470 rpm mounted on common m.s. fabricated base plate with suitable size of cidf sluice valve 1 no, cidf nr valve 1 no, foot valve 1 no, pressure gauge 1 no, tyre coupling 1 no etc all complete. head 50 m discharge 54 m3 / h ( hp 20 approx ) 1.02 supplying all labour tools and tackles for taking out old and damaged c / f pump set with all accessories , demolition of foundation for installation of new hsc centrifugal pump sets. 1.03 supplying all labour tools and tackles for making new pcc foundtiaon 2nos, of size 5′x3x3′ with all materials such as cement , sand, stone chips, foundation bolt 6nos etc all complete and plastering and punning over exposed surface. 1.04 cost for supply and laying of suction pipe line with supplying of 4 dia or suitable dia size as per pump at site heavy duty g.i. pipe 6m, bend 2 nos., flange 6 nos., nut, bolt, washer 10kg, rubber insertion 5kg etc, cutting of pipe in required size and doing complete welding work including all labour, tools, tackle and technician charges.with cp & ohc. ( rate after deducting the scrap materials. ) 1.05 cost for supply and laying of 3dia delivery pipe line with supplying of 3 dia or suitable dia size as per pump at site heavy duty g.i. pipe 6m, bend 1 nos., flange 4 nos., nut, bolt, washer 5kg, rubber insertion 5kg etc, cutting of pipe in required size and doing complete welding work including all labour, tools, tackle and technician charges. with cp & ohc. ( rate after deducting the scrap materials. ) for pump house no 1 & 2. 1.06 cost for supplying and laying of 3 core x 10 mm2, pvc insulated and pvc sheathed unarmoured copper cable of 1.1 kv grade. from panel to motor in 2 length each for both motor for both pump house with cp and ohc. 1.07 socketing of terminal ends with s / f of terminal socket including all labour tools and tackles. 3 core x 6 mm2, copper cable 24 ends. 1.08 providing floor / wall mounted cubical l.t motor control panel fabricated with ms sheet and painted, dust and vermin proof, proper ventilated, consisting of – proper distribution 100 amp copper bus bar 4 pole 1 set micro processor base tpn mccb 100 amp l&t / siemens make with earth fault relay for incoming feeder – 1no. mccb 63 amp tpn type l&t / siemens make for outgoing feeder 2 nos. ( 1no for each pump sets ) suitable size of fully automatic star delta starter make l&t / bch / schnider make 2 nos. 0 500 v voltmeter with selector switch 2nos ct operated ampere meter ( 0 200a ) with ct 2 sets with selector switch 2nos, phase indicating neon lamp 6nos, s.p.p. 2nos doing internal wiring with proper gauge of copper wire etc all complete job and testing on load. 1.09 cost towards supplying, installation, testing and commissioning of tpn main switch / isolator of 100a , make ( havells / schnieder / l&t / any reputed make isi marked. ) . each for pump house no 1 &2. 1.10 cost for supplying and laying of 3.5 core x 50 mm2, pvc insulated and pvc sheathed armoured aluminum cable of 1.1 kv grade. from electric pole to panel with cp and ohc. for pump house no 1 &2. 1.11 socketing of terminal ends with s / f of terminal socket including all labour , tools and tackles. 3.5 core x 50 mm2aluminium cable. 1.12 cost for doing chemical earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry with cover plate having locking arrangements and watering pipe 2.7 meter long etc with charcoal / coke and salt as required for chemical earthing. 1.13 supplying and laying of 8 swg copper wire for making earthing connection in two from earthing station to panel to motor . 1.14 cost of doing internal electric wiring with s / f of 3 / 20 single core copper cable with s / f of on off switches, indicator, fuses, sockets, switch board, junction boxes, pvc casing, nails & allied fittings etc including supplying and fixing 40 watt led tube light 2 nos, 12w led bulb 2 nos with all fittings etc including electrician charges for raw water pumping plant, clear water pumping plant pump house no 1&2 and outside of pump house etc all complete. 1.15 cost supplying and fixing of 40 watt led flood light with bracket with all fittings and accessories etc all complete for clear water premises. with c.p. & ohc. [ make havells / syska / mescab / bajaj / any reputed make. ] 2 supplying, installation, testing and commissioning of 2 set of new 175 hp vt pump sets and its allied work at raw water pumping plant , multi panchayat rural water supply scheme madhuban pirtand 2.01 supplying, installation, testing and commissioning of water lubricated vertical turbine pump [ make: kirloskar / mather & platt / jyoti / wpil ] capable of discharging 45 lps raw water against a total head of 185 meter at speed not more than 1500 rpm as per is: 1710 / 1989 with column length not less than 50 ft in 5ft each with closed type ss impeller, ss line shaft, ss shaft sleeves, flanged type ms column pipes suitable for below the floor installation and existing delivery header coupled with vertical hollow shaft operated on 415v±10%, 3 phase, ac, 50±5%hz, 4 pole, duty s1, insulation f, lt squirrel cage induction motor with suitable size of coupling as per latest is specification [ make: abb / bhel / crompton / marathon / jyoti / kirloskar ] having 10% more bhp than the pump, making alignment, making electrical connections, with all required tools, tackles, consumables as required, testing and commissioning on full load as per the direction of e / i. etc all complete. 2.02 cost towards dismantling, lifting of old 175 hp pump sets with all 200 mm dia column pipes from intake well and lowering new pump sets with all accessories along with all labour tools and tackles etc all complete. 2.03 cost towards breaking of old pcc foundation and removing of all garbage from pump house to outside with lead of 300 m with all labour tools and tackles etc all complete. 2.04 cost towards making of new pcc foundation sizing 3 x 3 x 1 with supplying and fitting of foundation bolt 4nos., cement, sand , stone chips, as required and plastering and punning over exposed surface etc with materials, all labour tools and tackles etc all complete. 2.05 cost towards supply and laying of 3c x 95 sq. mm copper cable, pvc insulated & pvc sheathed, 1100v grade, isi marked, make.havells / polycab / finolex / gemscab / any reputed make for 3 pump sets. 2.06 socketing of terminal ends with s / f of terminal socket including all labour , tools and tackles. 3 core x 95mm2, copper cable 12 ends. 2.07 providing floor mounted cubical l.t motor control panel fabricated with ms sheet and painted, dust and vermin proof, proper ventilated, consisting of – ( a ) incoming: ( i ) proper distribution 800 amp copper bus bar 4 pole 1 set ( ii ) mccb 800 amp. acb, make l&t / siemens for incoming feeder 1no. ( iii ) 0 500 v voltmeter 1no. with selector switch 1 no, ct operated ampere meter ( 0 500a ) 1no. selector switch 1 no, phase indicating neon lamp 3 nos. b ) outgoing: i ) mccb 630 amp. tpn type, make l&t / siemens for outgoing feeder 3 nos. ( 01 no for each pump set ) ii ) suitable size of fasd starter l&t / bch / schneider make 3 nos. iii ) 0 500 v voltmeter 3nos. with selector switch 3 nos, ct operated ampere meter ( 0 500a ) 3nos. selector switch 3 nos, phase indicating neon lamp 9 nos, single phase preventor 3 nos., doing internal wiring with proper gauge of copper wire etc all complete job with testing on full load. 2.08 cost towards supplying and fixing 5 ton capacity, triple spur gear type chain pulley block suitable for capacity as below with 6 meter lift complete with load chain and hand chain suitable for above lift , tested to 50% over load as per is 3832 carrying isi mark with travelling trolley etc. 3 repairing and overhauling of motor control panels, pump sets and its allied works at clear water pumping plant at maithan ( 14.5mld wtp ) of dhanbad urban water supply scheme phase ii 3.01 cost towards repairing and complete overhauling of motor control panel with all labour tool, tackles and technician charges for disconnecting the electric line & opening of electric wire connection inside panel. cleaning, checking, rectifying of faults with supply and fitting of contacter set ( 3tf56 1no and 3tf53 2no. ) seimens make or equivalent capacity of isi marked reputed make, over load relay 1no., transformer oil 30 liter, changing of ampere meter, voltmeter, indicating lamps etc all complete work, dressing and doing fresh electric connection with new wire and connector inside panel, rechecking of all connections and testing on full load. ( rate after deducting the cost of scrap materials ) . 3.02 cost towards repairing and overhauling of 150hp centrifugal pump and changing of its damaged parts such as pump shaft of en9 materials 1no., ss gland bush 2nos., neckring bush 2nos., checknut 2nos., bearing housing of c.i. materials 2nos. as per sample, supply and fitting of ball bearing skf make 6311 2nos. etc with all labour, tools and tackles, transporting etc all complete. ( rate after deducting the cost of scrap materials ) . 3.03 cost towards overhauling and repairing of 150hp, 3phase induction motor operated on 415v, 50hz, with dismantling of motor, heating, varnishing, supplying and fitting of lead bit having 4 nos hole including supply and fitting of brass nut bolt of 24mm in length with suitable dia for both ends terminal ( motor joint box end & mcp end ) for 150hp motor, supply and fitting of skf make 6319 ball bearing 2nos. etc all complete assembly of the motor and testing on load with all labour, tools and tackles, transporting etc all complete. ( rate after deducting the cost of scrap materials ) . 3.04 cost towards supply and laying of 3 c x 120 sq. mm copper, xlpe unarmoured cable, 1100v grade, from starter panel to motor for 4nos. motor. [ make polycab / finolex / havells / kei / gemscab / any reputed make ] with c.p and ohc etc. [ jsor dwsd 2021 146 m1062 6 ] 3.05 cost towards making cable mouth for above cable with s / f of lugs, pvc tape etc including all labour, tools, tackle and technician charges etc all complete 3.06 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonary with cover plate having locking arrangements and watering pipe 2.7 meter long etc with charcoal / coke and salt as required for chemical earthing. 3.07 supplying and laying of 8 swg copper wire for making earthing connection in to from earthing station to panel to motor . 3.08 cost towards supplying, installation, testing and commissioning of 40 watt semi integrated solar street light luminary including battery inside, g.i. pole 6mtrs, structure, arms , nut & bolts etc, suitable spv modules, 2.5 sq. mm x 2 core wire for connection with all labours, tools and tackles etc all complete. [ make havells / exide / any isi marked reputed make ] with cp & ohc. 3.09 cost towards supplying and laying of 2c x 2.5 sq. mm, pvc insulated and pvc round sheathed, copper conductor ( flexible ) industrial cable, 1100 volt, isi marked for common line for all 20nos. flood light as above. [ make havells / polycab / finolex / rr ] with cp & ohc. 4 renovation with supply installation testing and commissioning of pump set, overhauling of motor control panel and its allied work at rural water supply scheme, chirkunda kumardhubi, maithan ( old scheme ) 4. ( a ) raw water pumping plant : 4.01 cost towards supplying, installation, testing and commissioning of electrically driven horizontal split casing centrifugal pump set make ( kirloskar / wpil / mather & plate / jyoti ) coupled with tefc sq. cage induction motor make ( kirloskar / crompton / jyoti / abb ) operated on 415 + 10% volts, 50hz, 1470 rpm mounted on common m.s. fabricated base plate with suitable size of cidf sluice valve 1 no, cidf nr valve 1 no, foot valve 1 no, pressure gauge 1 no, tyre coupling 1 no etc all complete. head 50 m discharge 275 m3 / h ( hp 100 approx ) 4.02 supplying all labour tools and tackles for taking out old and damaged c / f pump set with all accessories , demolition of foundation for installation of new hsc centrifugal pump sets. 4.03 supplying all labour tools and tackles for making new pcc foundtiaon of size 6′ x 3 x 3′ with all materials such as cement , sand, stone chips, foundation bolt 6nos etc all complete and plastering and punning over exposed surface with all labour, tools, tackle and technician charges. 4.04 cost towards supply and laying of suction pipe line with s / f of 10 dia g.i. pipe 2 meter, 10 dia g.i. bend 1 no., 10dia g.i. flange 4nos., rubber insertion 10kg, nut, bolt & washer 10kg etc and cutting of pipe in required size and doing complete welding work including all labour, tools, tackle and technician charges.with cp & ohc. ( rate after deducting the scrap materials. ) 4.05 cost towards supply and laying of 8dia delivery line with s / f of 8 dia heavy duty g.i. pipe 1 meter, 8dia g.i. flange 4nos., rubber insertion 10kg, nut, bolt & washer 10kg etc and cutting of pipe in required size and doing complete welding work including all labour, tools, tackle and technician charges.with cp & ohc. ( rate after deducting the scrap materials. ) 4.06 cost towards overhauling of motor control panel with all labour tool, tackles and technician charges for disconnecting the electric line & opening of electric wire connection inside panel. cleaning, checking, rectifying of faults with supply and fitting of damaged spares such as bus bar 1set, ampere meter 1no., voltmeter 1no., indicating lamps 3 no. etc, dressing of motor cables with new lugs, crimping works etc all complete and testing on full load. ( rate after deducting the cost of scrap materials ) . 4.07 cost towards overhauling of f.a.s.d. starter panel with all labour tool, tackles and technician charges for disconnecting the electric line & opening of electric wire connection inside panel. cleaning, checking, rectifying of faults with supply and fitting of contacter set ( ml 4 1no and ml 6 1no. ) l&t make or equivalent capacity of isi marked reputed make, over load relay 1no., timer 1no., spp 1no. etc all complete work, dressing and doing fresh electric connection with new wire and connector inside panel, rechecking of all connections and testing on full load. ( rate after deducting the cost of scrap materials ) . 4.08 cost towards supplying and fitting of 40w led flood light, with bracket, copper wire, on off switch etc with all accessories including all labour tools , tackles and technician charges., with cp & ohc, ( rate after deducting the scrap materials. ) . make havells / syska / mescab / polycab / phillips 4.09 providing chipping work on the roof surface of raw water pump house, removing of all garbage to outside with lead of 50 m , providing and cleaning of concrete surface to remove dust and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. pounding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. on identification of seepage, cement grouting to be done with non shrink expanding admixture of sika lndia pvt.ltd. / myk schomberg / dr fixit / fosroc or equivalent. [ size 12.5 m x 6.7 m = 83.75 m2 ] 4.10 cost towards providing pcc m 200 in nominal mix of 1:1.5:3 on roof with approved quality of stone chips 12mm to 6mm size graded and clean course sand of fm 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of e / i. [ size 12.5 m x 6.7 m x 0.05 m= 4.19 m3 ] 4.11 providing 12 mm thick water proof cement plaster ( 1:3 ) with clean coarse sand of f m. 1.5 with integral water proofing compound liquid @125 ml per bag cement including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of e / i. brand fosroc conplast x421 lc, sika plastocrate plus, dr fixit pidiproof lw+, myk proof wp 10 or equivalent. [ size 12.5 m x 6.7 m = 83.75 m2 ] 4.12 dismantling old plaster and pointing in cement or lime and taking out joints to 15mm. depth, watering and disposal of unserviceable materials with all leads all complete as per direction of e / i. inside and outside of pump house, approx=280m2 4.13 providing 6mm thick cement plaster ( 1:4 ) in ceiling and wall of building with clean coarse sand of f.m. 15 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of e / i. 4.14 providing two coats of snowcem of approved shade and make over old surface including washing cleaning and preparing the walls , scaffolding, curing and taxes all complete as per building specification and direction of e / i. 4.15 providing 2 ( two ) coats of synthetic enamel paint of approved shade & make over steel surface including cleaning the surface, removing dirt, scales, smokes, grease, scaffolding & taxes all complete as per building specification and direction of e / i. for door, window, common header pipe, valves etc. approx 20m2 ( b ) clear water pumping plant : 4.01 cost towards supplying and fitting of complete rotating assembly for 50hp centrifugal pump, having head 65m discharge 113.5 m3 / hr make kirloskar with ss pump shaft, c.i. impeller, ss sleeve, bushes, gland tightener 2nos., ball bearing etc all complete with machining as per size and sample, assembling and fitting on the base plate, with all labour tools tackles and technician charges. ( rate after deducting the scrap materials. ) 4.02 cost towards supplying and fitting of complete rotating assembly for 50hp centrifugal pump, having head 70 m discharge 114 m3 / hr make wpil with ss pump shaft, c.i. impeller, ss sleeve, bushes, gland tightener 2nos., ball bearing etc all complete with machining as per size and sample, assembling and fitting on the base plate, with all labour tools tackles and technician charges. ( rate after deducting the scrap materials. ) 4.03 cost towards supplying and fitting of complete rotating assembly for 60hp centrifugal pump, having head 70 m discharge 160 m3 / hr make mather & platt with ss pump shaft, c.i. impeller, ss sleeve, bushes, gland tightener 2nos., ball bearing etc all complete with machining as per size and sample, assembling and fitting on the base plate, with all labour tools tackles and technician charges. ( rate after deducting the scrap materials. ) 4.04 cost towards supply and fitting of 4dia coupling set for 50hp pump set with nut bolt etc all complete. 4.05 cost towards supply and fitting of 4dia coupling set for 60hp pump set with nut bolt etc all complete. 4.06 supplying, fitting, installation, erecting and commissioning of approved make h.t. outdoor type gang operated air break triple pole switch, suitable for 11kv line, rotating type, with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps including cp, ohc , transportation, labour charges etc. ( rate after deducting the scrap materials. ) 4.07 cost towards supplying and fitting of 250a mccb, 3phase, 50hz, isi marked, with all labour tools , tackles and technician charges. with cp & ohc, ( rate after deducting the scrap materials. ) . make l&t / abb / hpl / cg 4.08 cost towards supplying and fitting of 160a mccb, 3phase, 50hz, isi marked, with all labour tools , tackles and technician charges. with cp & ohc, ( rate after deducting the scrap materials. ) . make l&t / abb / hpl / cg 4.09 cost towards overhauling of motor control panel cum 3 nos. of f.a.s.d. starter panel with all labour tool, tackles and technician charges for disconnecting the electric line & opening of electric wire connection inside panel. cleaning, checking, rectifying of faults of 3nos. f.a.s.d. starter with supply and fitting of contacter set ( mnx95 1no and mnx50 1no. ) l&t make or equivalent capacity of isi marked reputed make, over load relay 1no., timer 1no., spp 1no. etc all complete work each for 3 nos. fasd starter, dressing and doing fresh electric connection with new wire and connector inside panel, rechecking of all connections and testing on full load. ( rate after deducting the cost of scrap materials ) . for mcp no. 1. 4.10 cost towards overhauling of motor control panel cum 2 nos. of f.a.s.d. starter panel with all labour tool, tackles and technician charges for disconnecting the electric line & opening of electric wire connection inside panel. cleaning, checking, rectifying of faults of 2nos. f.a.s.d. starter with supply and fitting of contacter set ( mnx70 1no and mnx50 1no. ) l&t make or equivalent capacity of isi marked reputed make, over load relay 1no., timer 1no., spp 1no. etc all complete work each for 2 nos. fasd starter, dressing and doing fresh electric connection with new wire and connector inside panel, rechecking of all connections and testing on full load. ( rate after deducting the cost of scrap materials ) . for mcp no. 2. 4.11 cost towards supplying and fitting of 40w led flood light, with bracket, copper wire, on off switch etc with all accessories including all labour tools , tackles and technician charges., with cp & ohc, ( rate after deducting the scrap materials. ) . make havells / syska / mescab / polycab / phillips 4.12 providing chipping work on the roof surface of clear water pump house, removing of all garbage to outside with lead of 50 m , providing and cleaning of concrete surface to remove dust and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. pounding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. on identification of seepage, cement grouting to be done with non shrink expanding admixture of sika lndia pvt.ltd. / myk schomberg / dr fixit / fosroc or equivalent. 4.13 cost towards providing pcc m 200 in nominal mix of 1:1.5:3 on roof with approved quality of stone chips 12mm to 6mm size graded and clean course sand of fm 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of e / i. 4.14 providing 12 mm thick water proof cement plaster ( 1:3 ) with clean coarse sand of f m. 1.5 with integral water proofing compound liquid @125 ml per bag cement including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of e / i. brand fosroc conplast x421 lc, sika plastocrate plus, dr fixit pidiproof lw+, myk proof wp 10 or equivalent. 4.15 dismantling old plaster and pointing in cement or lime and taking out joints to 15mm. depth, watering and disposal of unserviceable materials with all leads all complete as per direction of e / i. inside and outside of pump house, 4.16 providing 6mm thick cement plaster ( 1:4 ) in ceiling and wall of building with clean coarse sand of f.m. 15 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of e / i. 4.17 providing two coats of snowcem of approved shade and make over old surface including washing cleaning and preparing the walls , scaffolding, curing and taxes all complete as per building specification and direction of e / i. 4.18 providing 2 ( two ) coats of synthetic enamel paint of approved shade & make over steel surface including cleaning the surface, removing dirt, scales, smokes, grease, scaffolding & taxes all complete as per building specification and direction of e / i. for door, window, common header pipe, valves etc....

East Central Railway - Jharkhand

32477953 supply of manufacture, testing and supply of dischargingmanufacture, testing and supply of discharging,manufacture, testing and supply of discharging load box for nickel cadmium battery as per following 1. resistance material nickel chromium alloy. 2. rating 110v, 60amps. 3. on load variation tap for 20,10, 5 and 2 amps respectively. 4. maximum permissible temperature 300 deg c 5. cooling forced. 6. enclosure set of resistance housed in ms structure with ammeter & voltmeter to monitor load current & voltage....

Drinking Water And Sanitation Department - Jharkhand

32472818 e quotation for repairing and rewinding of 5 h.p motor for govt. building w/s golmuri p/p e quotation for repairing and rewinding of 5 h.p motor for govt. building w/s golmuri p/p , cost towards dismantling of the 5 h.p kirloskar motorfrom foundation and taken out rotor from stator etc. all complete , cost towards complete stator rewinding of 5 h.p sq. cage induction motor 3 phase 50 c/s, 1440 rpm with super enameled copper wirealong with all requiredmaterials, such as sleeves tape, cotton tape, glass tape etc. includingvarnishingheating all complete.(after the deductioncost of scrap materials) , cost towards straightening of the pump shaft and remetaling with machining, turning and finishing all complete. , cost towards supplying and fittingballbearing 2306 and proper greasing all complete. , cost towards making s/f g.m neck ring as per size and sample 5 h.p. c/f pump set. , cost towards making s/f, g.m bush as per size andsample 5 h.p. c/f pump set. , supplying and fixing 63 amp. 415± 15% voltage change over switch, havells / l & t make , supplying and fitting cubical type duly painted control panel boardconsisting 32 amps. tpn mccb inbuilt single phase preventor and suitable forstar delta automatic starter water level guard with suitable length and size of wire phase indicating bulb in three different colour suitable voltmeter and ampere meterwith selector switch make l&t / havell;s , chemical earthing3 metersand80 mm hole size with electrode and chemical compound etc. with watering pipe and locking arrangement including soldering, riveting, jointing g.i flat 50 mm x 6 mm to all equipments. ( for p/set no. 01 & 02) , cost towards supplying and fitting150w street light with all complete fitting such ascomplete cover with glass / fiber fitting with suitable cable nut, bolt etc all complete. make philips / bajaj /any reputed make...

South Eastern Railways - Jharkhand

32439414 supply of meter calibration unitmeter calibration unit, meter calibration unit as per technical specification mentioned below ( 1 ) kv meter ( aux. line voltmeter ) , range ( 0 600v ac ) & ( 0 35kv ) , 3 1 / 2 dpm, disply range: 600v ac, resolution : 1v ac ( 2 ) line voltmeter ( traction motor voltmeter ) , range ( 0 1.8kv dc or 0 900v dc ) , 3 1 / 2 dpm, display range: 0 2000v dc, resolution: 1v ( 3 ) ammeter ( traction motor ammeter ) , range ( 1500a 0 1500a ) , changeover / toggle switch for + / current simulation, 3 1 / 2 dpm, display range 2000a, resolution: 1a ( 4 ) uba meter ( battery voltmeter ) , range ( 0 150v dc ) , 3 1 / 2 dpm, display range: 200v, resolution:0.1v ( 5 ) traction / braking effort meter bogie, range ( 100te 0 100be ) , fs: 10v dc 0 10 v dc, 3 1 / 2 dpm, display range: 200, resolution: 1 unit ( 6 ) catenary voltmeter, range 0 30 kv, fs: 10v dc, 3 1 / 2 dpm, display range: 30kv, resolution:0. 1 kv...

Department Of Technical Education - Jharkhand

32317733 bids are invited for sextant measuring tape , young s modulus , 3 1 2digit digital multimeter manual range , carrey foster bridge with four gap complete setup , norton s theorem with bakelite panel and round meters , thevenin s theorem with bakelite panel and round meters , pn zener diode led characteristics apparatus , thermo electric , to determine the refractive index of the material of a prism using sodium light , determine the wave length of sodium lamp by newton ring method , universal b.h curve apparatus , zener diode , fet characteristics apparatus with aluminum panel and square meters , mosfet characteristics apparatus with aluminum panel and square meters , amplitude modulation and demodulation , operational amplifier as inverting, non inverting, unity gain amplifier and frequency response with analog voltmeter , operational amplifier as differentiator and integrator , determine of the specific rotation of the cane sugar solution with the help of polarimeter , boltzman constant apparatus with pn junction diode with aluminum panel and digital panel meters , to determine 1 wavelength he ne laser using plane diffraction grating. complete set , strain gauge trainer kit with cantilever beam , molecular atomic models , magnetic stirrer with hot plate , rotary flask shaker , variable volume micropipette , analytical balance , double beam uvvis spectrophotometer , benzaldehyde 500ml , aniline 500ml , ethyl alcohlal 500ml , acetone 500ml , benzoic acid 500gm , benzene 500ml , phosphoric acid 500ml , barium diphenylamine sulphonate ar 25gm , hydrogen fluoried 500gm , digital tds meter labtronics , dissolved oxygen meter , dissolved turbidity meter , maximum minimum therme meter , ph meter , phytoplankton net mesh size 10, 25, 50, 100 , plankton counting cell sedwich rafter , secchi disk , haemocytometer , insect box...

Department Of Labor And Employment - Jharkhand

32295197 bids are invited for measuring steel tape , combination plier insulated , screw driver insulated , electrician screw driver , heavy duty screw driver , electrician screw drive , punch centre , knife double bladed , neon tester , steel rule graduated , hammer cross peen , pipe vice cast iron , hand vice , table vice , hacksaw frame , file flat , file half round , file round , pliers long nose , pliers flat nose , pliers round nose insulated , de metric spanner double ended , wire gauge , portable electric drill machine , crimping tool , pliers side cutting , wire stripper , hammer ball peen with hndandle , scriber , tool kit box or bag , allen key , scissors blade , torque wrench , pipe cutter to cut pipes , try square , multi meter analog , load bank , wire cutter and stripper , earth plate , earth electrode , out side micrometer , tap set , trolley for transportation of batteries , die for threading , electrical wiring and switch gear rack , protective relays and contactors rack , mccb , elcb and rccb , plumbing tools , multimeter digital , megger , hydrometer , solar insulation meter , pyranometer , pyrheliometer , lux meter , magnetic flux meter , tong tester or clamp meter , soldering iron , temperature controlled soldering iron , thermometer digital , sun shine recorder , magnetic compass , cut models of photo voltaic cell assembly , cut model of lead acid battery , solar simulator , curve tester , sun path finder , solar energy trainer , solar tracker demonstrator kit , halogen lamp , motorized bench grinder , battery charger , solar photovoltaic module , solar panels , solar charge , solar charge , array junction box , solar lantern , solar lantern assembly sets , home light system , solar cell kit , clinometer , spirit level , anemometer , dc table fan , ac voltmeter , volt meter , ammeter mc , ammeter mc centre zero , power factor meter , rheostat , ac energy meter , kilo wattmeter analog , digital wattmeter , phase sequence indicator , frequency meter , dc led lamp , dc pump , pwm controller , mppt charge controller , solar pcu , solar grid tied inverter demonstrator kit , solar street light , solar wind and hybrid power plant , solar traffic light , used water treatment solar plant demonstrator kit , demonstration kit for wind generation , rubber gloves , cotton gloves , gum boots , safety goggles , safety helmet , first aid kit , fire extinguisher , fire buckets , working bench , wiring board , white board...

Department Of Atomic Energy - Jharkhand

32291292 bids are invited for earth leakage relay , ammeter , voltmeter , contactor , no volt coil for 300a contactor , ct operated thermal over load relay , i s pilot panel intrinsically safe , heavy dutyscrew assembly for plug and socket , inter lock assembly ,circlip for plug and socket , auxiliary contactor , pilot relay total quantity : 407...

Jharkhand State Building Construction Corporation Limited - Jharkhand

32287667 niq for minority residential niq for minority residential school margo munda, deoghar , phartiha, garhwa district. barhate, sahebganj district name of work : .(3.) construction of school with residential building for minority community at margo munda, deoghar district.(4.) construction of school with residential building for minority community at phartiha, garhwa district.(6)proposed construction of residential school for minority group at barhate, sahibganj, jharkhand mr fabrication, supplying, installation, testing & commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick crca sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 v, 3 phase 50 hz ac supply with enclosure protection class ip 42. for terrace pump mr fabrication, supplying, installation, testing & commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick crca sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 v, 3 phase 50 hz ac supply with enclosure protection class ip 42. for terrace pump mr supplying fitting fixing pressure gauge assemble with gate/ball valve all complete with labor and material as per engineer in charge. mr supplying fitting fixing air release valve / drain valve all complete with labor and material as per engineer in charge. mr supplying fitting fixing ms structure support for piping all complete with labor and material as per engineer in charge. mr supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick m.s. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect. mr providing , fixing dry chemical powder (stored pressure type) mono ammonium phosphate 50% powder confirming to ‘is 14609’ , nitrogen pressurized, controllable discharge mechanism, pressure gauge, discharge hose & nozzle epoxy polyester powder coated as per ‘is 15683’ isi mark fire extinguishers. operating temperature: ( ) 20oc to (+) 55oc suitable for ‘a’ ‘b’ ‘c’ class of fire complete in all respects (4 kg capacity) mr stainless steel text (text height 250 mm ) at pergola slab with grouting all complete including matrial & labour as pet e/i mr carbon di oxide type , gas confirming to is ‘15222’ , cylinder confirming to ‘is 7285’ & peso approved ,controllable discharge mechanism, discharge hose & horn as per ‘is 15683’ & ‘is 2878’ isi mark fire extinguishers (wheel type or squeeze grip type). operating temperature : ( )20oc to (+)55oc suitable for ‘b’ ‘c’ class of fire (4.5 kg capacity) mr providing , fixing modular type fire extinguishers for electrical rooms (stored pressure type) mono ammonium phosphate 50% powder confirming to ‘is 14609’ , nitrogen pressurized, controllable discharge mechanism, pressure gauge, discharge hose & nozzle epoxy polyester powder coated as per ‘is 15683’ isi mark fire extinguishers. operating temperature: ( ) 10oc to (+) 55oc suitable for ‘a’ ‘b’ ‘c’ class of fire complete in all respects (5 kg capacity) mr providing and fixing 25 mm nominal gun metal gate valve class i with ci wheel of approved quality with union (screwed end) mr main lt panel for main building : supplying, designing, manufacturing, installation, testing and commissioning of lt panel of 14 swg crca sheet (2 mm) steel , dust and vermin proof with reinforcement of suitable size iron channel , with proper lifting arrangement effecting proper connection of all incomers and outgoing(ip 43) fully compartmentalized cubical type, floor mounted , totally enclosed, extendable on both sides, switch board and suitable for operation on 415v, 50hz, 3 ph. ac supply and fault level 50 ka with front operated construction including separate fabrication arrangement for fixing mccbs and bus coupler. the sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 nos. earth studs.the panel includes 415v, 200a, 3ph, 50ka, 50hz electrolytic aluminium bus bar (e91ewp) aluminium, earth bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing feeders complete in all respects. all inter connections shall be made with 2.5 4, 6, 10 sq mm pvc cu. wire. main lt panel for main building : supplying, designing, manufacturing, installation, testing and commissioning of lt panel of 14 swg crca sheet (2 mm) steel , dust and vermin proof with reinforcement of suitable size iron channel , with proper lifting arrangement effecting proper connection of all incomers and outgoing(ip 43) fully compartmentalized cubical type, floor mounted , totally enclosed, extendable on both sides, switch board and suitable for operation on 415v, 50hz, 3 ph. ac supply and fault level 50 ka with front operated construction including separate fabrication arrangement for fixing mccbs and bus coupler. the sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 nos. earth studs. the panel includes 415v, 200a, 3ph, 50ka, 50hz electrolytic aluminium bus bar (e91ewp) aluminium, earth bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing feeders complete in all respects. all inter connections shall be made with 2.5 4, 6, 10 sq mm pvc cu. wire.all incomer mccb and bus coupler shall be mechanically operated . all 4 pole mccb with thermomagnetic based release must have following character: icu=100% ics with adjustable s/c and o/lprovision for inbuilt earth leakage module & provision for inbuilt measuring unit. the panel consisting of the followings, 4 pole mccb 160 a, 35 ka with fixed thermal magnetic setting 1 no, provision of mechnical interlocking between 125a/fp/25ka mccb as common incoming and 1 no. of 125a on load change over for d.g incomer, in such a way so that the two supplies are not parallel at any time.1 no. 125a tpn on load change over panel mounted open execution type and suitable bus arrangement for cable termination. make l&t/sucomo. 1 no. 125a/fp/16ka/ mccb thermomagnetic release type, and s/c, o/l protection, with rotary handle & spreader links. mcb tpn 40a 10 nos, mcb dp 40a 2nos( oter light+spare), mcb dp 63a 6 nos( pdb+ups+spare),electronic on timer delay 30 sec, 200 amp 415 v heavy duty three phase with neutral busbar chamber, indicator switch 3 nos, selector switch, analog voltmeter 3 nos, analog ameter, c.t. coil mr main lt panel for hostel building : supplying, designing, manufacturing, installation, testing and commissioning of lt panel of 14 swg crca sheet (2 mm) steel , dust and vermin proof with reinforcement of suitable size iron channel , with proper lifting arrangement effecting proper connection of all incomers and outgoing(ip 43) fully compartmentalized cubical type, floor mounted , totally enclosed, extendable on both sides, switch board and suitable for operation on 415v, 50hz, 3 ph. ac supply and fault level 50 ka with front operated construction including separate fabrication arrangement for fixing mccbs and bus coupler. the sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 nos. earth studs. the panel includes 415v, 200a, 3ph, 50ka, 50hz electrolytic aluminium bus bar (e91ewp) aluminium, earth bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing feeders complete in all respects. all inter connections shall be made with 2.5 4, 6, 10 sq mm pvc cu. wire.all incomer mccb and bus coupler shall be mechanically operated . all 4 pole mccb with thermomagnetic based release must have following character: icu=100% ics with adjustable s/c and o/lprovision for inbuilt earth leakage module & provision for inbuilt measuring unit. the panel consisting of the followings 4 pole mccb 160 a, 35 ka with fixed thermal magnetic setting 1 no 1 no. 125a tpn on load change over panel mounted open execution type and suitable bus arrangement for cable termination. make l&t/sucomo. 1 no. 125a/fp/16ka/ mccb thermomagnetic release type, and s/c, o/l protection, with rotary handle & spreader links. mcb tpn 40a 10 nos, mcb dp 40a 6nos( outer light+spare) , mcb dp 63a 4 nos( ups+spare), electronic on timer delay 30 sec , 200 amp 415 v heavy duty three phase with neutral busbar chamber , indicator switch 3 nos , selector switch, analog voltmeter 3 nos, analog ameter, c.t coil mr sitc of 24x ports 10/100/1000base t ports,4x 1g sfp ports, supports poe standards ieee 802.3af, 802.3at,1x usb c console port,1x usb,up to 370 w of class 4 poe power, fanless design, with dual core arm cortex a9 @ 1016 mhz cpu, memory 4 gb ddr3 16 gb emmc , packet buffer size of 12.38mb (4.5mb ingress/7.875mb egress),ipv6 ready certified mac address table size: 16000 entries;average latency 1 gbps latency: < 1.5 µs (lifo 64 byte packets), throughput: up to 41.6 mpps (64 byte packets), switching capacity: 56 gbps, operating temperature 32°f to 113°f (0°c to 45°c) up to 5000 ft (1.5 km), certifications ul,en,fcci, preferred make hp/aruba/allied telesis/cisco/netgear or as approved by e/i mr sitc of 12x ports 10/100/1000base t ports,2x 1g sfp ports,2x 1gbe ports , supports poe standards ieee 802.3af, 802.3at,1x usb c console port,1x usb,up to 139w of class 4 poe power, fanless design,with dual core arm cortex a9 @ 1016 mhz cpu, memory 4 gb ddr3 16 gb emmc , packet buffer size of 12.38mb (4.5mb ingress/7.875mb egress),ipv6 ready certified mac address table size: 16000 entries;average latency 1 gbps latency: < 1.5 µs (lifo 64 byte packets), throughput: up to 23.8 mpps (64 byte packets), switching capacity: 32 gbps, operating temperature 32°f to 113°f (0°c to 45°c) up to 5000 ft (1.5 km), certifications ul,en,fcci, preferred make hp/aruba/allied telesis/cisco/netgear or as approved by e/i mr sitc of 24 port utp jack panel (24 port rj 45 loaded cat 6 utp 19 rackmountable patch panel preferbaly with 6 blocks). (make:legrand/panduit/rit/siemon) detailed specs for 19 1u 24 port unsheilded, patch panel patch panel should be modular design, populates up to 24 utp keystone type jacks in 1u, patch panel should be enhanced with cable strain relief with retention tray; it should be single metal both front panel and rear tray, material: sub rack made of ms steel with dimension 44.4 mm : 482.6 mm : 105 mm (h:w:d) tray, information outlet or connectin module should comply with the specification mentioned above in 2, standard : conforms to iec 60603 7 (603 7) for keystone type, snap on apertures, should be rohs complied mr sitc of straight lan patch chord 1 mtr (make:legrand/panduit/rit/siemon) ,detailed specs for patch cord, u/utp 4p, cat.6, length  1/3 metre, standardization: compliant with cat.6, class e requirements: iso/iec 11801 2nd edition compliant with cat.6 component standards iec 60603 7 4 and 60603 7 5 , cable shield:  u/utp, number of conductors : 8 , stranding: 7 x 0.20 mm (24 awg), cable jacket characteristics: cable, metal free cable overall diameter: 6.5±0.2 mm, tube / wire type: stranded conductor, insulation: solid polyolefin, 0.97±0.02 mm diameter ,plug: feature cable retension, with enhanced pull strength., cat 6 patch cord plug to have round cable holder and strain relief boot to avoid bending. jacket: pvc with 8 different color options,plug should have high repeatability cross talk performance mr sitc of fully loaded 9u 19 600*500 wall mounted rack with all required accessories 2 nos. of fan,6a 6 plug pdu 1 nos. ,cable manager 2 nos., mounting screws 20 pcs ; preffered make legrand/apw/president/valrack/netrack mr sitc of epabx system: ip based 100% non blocking epabx system should be a ip compatible with rich feature set of the system and can be connected with pure voice over ip (voip) communication network across corporate local and wide area networks (lan and wan) as & when required. central processing unit: the system main software should be open architecture based. the cpu of main system shall be 32 bit processor working at 2.0 ghz or better. the system should be wall mountable. • system architecture should be latest pure ip and should be wall mountable; meet me conference 30 party x 2 from day 1 must be available. must support unified communications equipped with 16 analog extensions expandable upto 48 extensions,4 analog trunk ports,epabx make: avaya/nec/unify mr analog basic push button telephone: sitc of analog telephone make: panasonic/ bpl/beetel mr sitc of telephone tag block): ip 65( weather proof). preffered make krone 50 pair krone box fully loaded without ipm mr supply, fitting, fixing, commissioning and testing of 16 sq. mm copper conductor multi strand pvc sheilded frls wire with suitable copper lugs for battery interconnection and suitable 16 sq. mm copper wire of 2 length of 10 mtrs each for ups to battery excluding cable from panel to ups and ups to panel. make polycab/havells/kei mr chemical earthing: supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except g.i. strips (25mmx5mm) each earth pit has to be tested with earth tester 1000 v/1000 ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. the above chemical earthing includes the provision of masonary enclosure and hdpe earth pit cover 300mm x 300 mm (under floor earth inspection pit) having locking arrangement as earth chamber.the above chemical earthing includes the following items (3 mtr earthing) ; each chemical earthing shall have following details: supply of pollution free earthcon compound 4 bags of 25 kg each ; supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 mtr long electrode. tested as per iec 62561 2. meets the requirement of is 3043 & iec 60364 5 54. tested for short circuit withstanding capacity. high tensile strength. (ul listed).; supply of stainless steel u bolt clamp; supply of hdpe earth pit cover for earth chamber (capacity of 5 ton) ; sub total c( ups system & accessories) mr sitc of 5mp fixed lens network bullet camera with following technical specifications; preffered make: honeywell/bosch/hikvision/pelco/sony image sensor : 1/2.7 progressive scan cmos, min. illumination : color: 0.003 lux @ (f1.4, agc on), b/w: 0 lux with ir preferred recording resolution: 5mp (2592x1944) or better ,day & night: ir cut filter , shutter speed: 1/3 s to 1/100,000 s, digital noise reduction; 3d dnr ,wdr: 120db true wdr or better, lens; 4mm , ir range : 40m ir or higher ,streaming type: should support quad video streams or better ,video compression: h.265,h.264, h.264+,h.265+,mjpeg and main stream supports h.264+/h.265 , audio compression: g.711ulaw/g.711alaw/g.722.1/g.726/mp2l2/pcm/mp3 , image enhancement: blc, hlc, 3d dnr, eis, defog,roi , (5 fixed regions for main stream and sub stream). image settings: rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser , day/night switch: day, night, auto, schedule , network protocol : tcp/ip, icmp, http, https, ftp, dhcp, dns, ddns, rtp, rtsp, ntp, upnp, smtp, igmp, 802.1x, qos, ipv4, ipv6, udp, bonjour, ssl/tls, pppoe, arp, snmp,open network video interface (profile s, profile g, profile t),isapi. simultaneous live view: 6 channeluser host: 32 users. 3 user levels: administrator, operator and usersecurity: password protection, complicated password, https encryption, ip address filter, security audit log, basic and digest authentication for http/https, tls 1.2, wsse and digest authentication for open network video interface, memory card encryption.edge base recording storage: built in memory card slot, support microsd card, up to 256 gb ,preferable analytics features: motion detection, video tampering alarm, line crossing detection, intrusion detection,scene change detection, video quality diagnosis.event alarm: notify surveillance center, trigger recording, trigger capture, send email, audible warning,network disconnected, illegal login.ethernet port: 1 x rj45 10m/100m ethernet port, audio interface; 1x input, 1x output , power supply: dc12v, poe (802.3af) , operating conditions: 30° c ~ + 60° c ingress protection: ip67 , certifications: ce, fcc, ul,bis. mr sitc of 32 channel nvr processor : dual core embedded processor, operating system : pre loaded licensed os,ip camera support up to 32 ch , should support h.265+/h.265/h.264+/h.264 video formats, up to 2 ch @ 8mp or 4 ch @ 4mp or 8 ch @ 1080p decoding capacity,1 hdmi and 1 vga interfaces: both interfaces support independent video output,4 hdds for continuous video recording, up to 256 mbps incoming bandwidth, outgoing bandwidth 160 mbps, audio output 1 ch, rca (2.0 vp p, 1 kω, using the audio input ),two way audio 1 ch, rca (2.0 vp p, 1 kω, using the audio input ),video output mode hdmi/vga independent output, recording resolution 12 mp/8 mp/6 mp/5 mp/4 mp/3 mp/1080p/uxga/ 720p/vga/4cif/dcif/2cif/cif/qcif,sata 4 sata interfaces of capacity up to 10tb capacity for each hdd, serial interface 2 rs 485 (half duplex), 1 rs 232, usb interface front panel: 2 × usb 2.0; rear panel: 1 × usb 3.0, smart phone connectivity through app or browser : iphone, ipad, android, windows phone, should support multiple vca (video content analytics) events, configurable special camera smart functions, such as vca detection (motion, line crossing, intrusion, etc.), heat map, anpr, and people counting power sitc : ac 100v~240v, 50/60hz,regulatory : ce, fcc,ul and rohs; preferred make: honeywell/bosch/hikvision/pelco/sony mr sitc of 16 channel nvr processor : dual core embedded processor, operating system : pre loaded licensed os,ip camera support up to 16 ch , should support h.265+/h.265/h.264+/h.264 video formats, up to 2 ch @ 8mp or 4 ch @ 4mp or 8 ch @ 1080p decoding capacity,1 hdmi and 1 vga interfaces: both interfaces support independent video output,4 hdds for continuous video recording, up to 256 mbps incoming bandwidth, outgoing bandwidth 160 mbps, audio output 1 ch, rca (2.0 vp p, 1 kω, using the audio input ),two way audio 1 ch, rca (2.0 vp p, 1 kω, using the audio input ),video output mode hdmi/vga independent output, recording resolution 12 mp/8 mp/6 mp/5 mp/4 mp/3 mp/1080p/uxga/ 720p/vga/4cif/dcif/2cif/cif/qcif,sata 4 sata interfaces of capacity up to 10tb capacity for each hdd, serial interface 2 rs 485 (half duplex), 1 rs 232, usb interface front panel: 2 × usb 2.0; rear panel: 1 × usb 3.0, smart phone connectivity through app or browser : iphone, ipad, android, windows phone, should support multiple vca (video content analytics) events, configurable special camera smart functions, such as vca detection (motion, line crossing, intrusion, etc.), heat map, anpr, and people counting power sitc : ac 100v~240v, 50/60hz,regulatory : ce, fcc,ul and rohs; preferred make: honeywell/bosch/hikvision/pelco/sony mr sitc of 6tb surveillance grade hard disk for nvr for 30 days back up; make seagate/wd mr 43 4k led panel,preffered make lg/samsung/panasonic mr supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick m.s. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect. ...

East Central Railway - Jharkhand

32193448 supply of catenary voltmeter,range 15.5kv 25.9 kv specification : clw spec.no. clw/es/3/0070catenary voltmeter,range 15.5kv 25.9 kv specification : clw spec.no. clw/es/3/0070,catenary voltmeter,range 15.5kv 25.9 kv specification : clw spec.no. clw/es/3/0070 csd/trs/mgs , ecr uttar pradesh 16.00 numbers...

Jharkhand State Electricity Board - Jharkhand

31955758 rate of materials supply of materials ( i ) rail pole 60 kgs 13 meter ( ii ) rail pole 52 kgs 13 meter ( iii ) rs joist pole 9.3 meter ( 175x85mm ) 19.6 kgs per mtr ( iv ) rs joist pole 9 meter ( 116x100mm ) 23 kgs per mtr ( v ) 125x70x5 rs gi joist 8mtr ( 13.3kg / mtr ) ( vi ) wpb 160x160, 30.4kg / m weather resistant h beam, 11m ( vii ) wpb 160x160, 30.4kg / m weather resistant h beam, 13m ( viii ) psc pole 400 kg w.l ( 9 mtr. ) ( ix ) psc pole 200 kg w.l ( 8 mtr. ) ( x ) steel tubular pole ( sp 32 ) of 9 meter ( xi ) steel tubular pole ( sp 55 ) of 11 meter ( xii ) steel tubular pole ( sp 72 ) of 13meter acsr conductors ( i ) acsr panther conductor ( 232 sq. mm ) ( ii ) acsr wolf conductor ( 150 sq. mm ) ( iii ) acsr dog conductor ( 100 sq. mm ) ( iv ) acsr racoon conductor ( 80 sq. mm ) ( v ) acsr rabbit conductor ( 55 mm2 ) ( vi ) acsr weasel conductor ( 34 sq. mm ) insulators & h / w fittings ( i ) 33 kv pin insulator 10 kn with pin ( porcelain type ) ( ii ) 33 kv polymer pin insulators 10 kn with gi pin and nut & washer ( iii ) 33 kv disc insulator ( polymer type ) 90 kn with h / w fitting and nut & washer ( iv ) 33 kv disc. insulator ( porcelain type ) 70 kn with h / w fitting ( v ) 33 kv disc insulator ( polymer type ) 70 kn with h / w fitting ( vi ) suspension hardware suitable for panther conductor ( vii ) tension hardware suitable for panther conductor ( viii ) 11 kv pin insulator 10 kn, od 40 mm dia with pin ( polymer type ) and nut & washer ( ix ) 11 kv pin insulator 5kn with pin ( porcelain type ) ( x ) 11 kv pin insulator 5 kn with pin ( polymer type ) and nut & washer ( xi ) 11 kv disc insulator ( polymer type ) 70 kn with h / w ( xii ) 11 kv disc insulator ( porcelain type ) 45 kn with h / w ( xiii ) 11 kv disc insulator ( polymer type ) 45 kn with h / w ( xiv ) lt pin insulator with pin ( porcelain type ) ( xv ) lt pin insulator ( porcelain type ) ( xvi ) lt shackle insulator ( porcelain type ) ( xvii ) lt shackle strip with bolts and nut ( xviii ) 33 kv post insulator 10 kn ( polymer ) ( xix ) 11 kv post insulator 5 kn ( polymer ) ( xx ) 33 kv stay insulator ( xxi ) 11 kv stay insulator ( xxii ) lt stay insulator ( xxiii ) mid span compression joints suitable for acsr panther conductor ( xxiv ) repairing sleeve suitable for acsr panther conductor isolator ( i ) 33 kv isolator 800 amp , 3 phase, with earth switch ( ii ) 33 kv isolator 800 amp , 3 phase, with out earth switch ( iii ) 33 kv isolator 630 amp, 3 phase, without earth switch ( iv ) 33 kv isolator 630 amp, 3 phase, with earth switch ( v ) 33 kv isolator 400 amp, 3 phase, with earth switch ( vi ) 11 kv isolator 630 amp, 3 phase, with earth switch ( vii ) 11 kv isolator 630 amp, 3 phase, without earth switch ( viii ) 11 kv isolator 400 amp, 3 phase, without earth switch ( ix ) 11 kv isolator 400 amp, 3 phase, with earth switch ( x ) 11 kv isolator 200 amp single phase ab switch ( i ) 33 kv 3 pin type, 3 phase, ab switch 800 amp ( porcelain type ) ( ii ) 33 kv 3 pin type, 3 phase, ab switch 630 amp ( porcelain type ) ( iii ) 33 kv 3 pin type, 3 phase, ab switch 630 amp ( polymer type ) ( iv ) 11 kv 3 pin type, 3 phase, ab switch 630 amp ( porcelain type ) ( v ) 11 kv 3 pin type, 3 phase, ab switch 400 amp ( polymer type ) ( vi ) 11 kv 3 pin type, 3 phase, ab switch 400 amp ( porcelain type ) ( vii ) 11kv ab switch 200 amps ( single break ) lightening arrestor ( i ) lightening arrestor ( 9kv 5ka ) line type ( ii ) 11 kv lightening arrester ( 9 kv, 10 ka class ii, station type ) ( 1set=3nos ) ( iii ) 33 kv lightening arrester ( 30kv, 10ka class ii, station type ) ( 1set=3nos ) earthing ( i ) 25mm dia ms rod 3 m long for earth mat ( ii ) spike earthing made of 20mm gi solid rod ( iii ) g.i earthing strip size 75x8 mm ( iv ) g.i earthing strip size 35x3 mm ( v ) g.i earthing strip size 35x4 mm ( vi ) g.i earthing strip size 40x4 mm ( vii ) g.i earthing strip size 40x5 mm ( viii ) insulated gi / alum.flexible wire 16 sq.mm ( ix ) ace chemrod ( artificial concept of earthing by chemical rod ) : ace chemrod earthing electrode ( consisting mild steel galvanised pipe of size 2500 mm in length x 48 mm outer dia. x 2 mm thick, ms rod of size 2575 mm x 16 mm be welded with bottom. the epoxy insulator of not less than 100 mm length is to be fixed on top of mild steel galvanised pipe. a highly conductive substance is to be filled in residual gap between pipe and rod ) with highly conductive substances not less than 25 kg for soil treatment ( x ) earthing complete conventional type having intermittent layer of charcoal and salt stay set ( i ) gi stay set complete for d / s / s ( 1900x 16mm ) with staywire 7 / 12 swg and guy insulator ( ii ) gi stay set complete for d / s / s ( 1900x 20mm ) with staywire 7 / 10 swg and guy insulator ( iii ) stay set complete ( 1800x20mm ) with stay wire 7 / 10 swg & guy insulator ( galvanised ) ( iv ) 11 kv stay set complete ( 1800x16 mm ) with stay wire 7 / 10 swg and guy insulator ( v ) lt stay set complete ( 1700x16 mm ) with stay wire 7 / 12 swg ( vi ) gi stay wire no. 7 / 8, 7 / 10, 7 / 12, 7 / 14, 7 / 16 p.g.clamps ( i ) p g clamp for 232 / 150 sq mm conductor ( ii ) p g clamp for 80 / 100mm2 ( iii ) p g clamps for 34 / 55mm2 ( iv ) bimettalic clamps for distribution transformers ht side ( 25 to 200 kva ) ( v ) bimettalic clamps for distribution transformers ht side above ( 200 kva ) ( vi ) bimettalic clamps for distribution transformers lt side ( 25 to 200 kva ) ( vii ) bimettalic clamps for distribution transformers lt side above ( 200 kva ) ( viii ) bimettalic clamps for power transformer 5 mva ( ix ) bimettalic clamps for power transformer 10 mva ( x ) bimettalic clamps for vcbs for 33kv and 11 kv ( xi ) bimettalic clamps for ct pt unit ( xii ) p g clamp 3 bolt for abt meters structures, gantry columns and base plates ( i ) structure for 33kv lightening arrestor [ non galvanized ] ( ii ) structure for 33kv lightening arrestor [ galvanized ] ( iii ) structure for 33 kv isolator ( galvanised ) ( iv ) structure for 11 kv isolator ( galvanised ) ( v ) structure for 33 kv isolator [ galvanized ] ( vi ) structure for 11 kv isolator [ galvanized ] ( vii ) structure for 33 kv pt ( non galvanised ) ( viii ) structure for 33 kv pt [ galvanized ] ( ix ) structure for 11 kv pt ( non galvanised ) ( x ) structure for 11 kv pt [ galvanized ] ( xi ) structure for post insulator for 11kv ( galvanised ) ( xii ) structure for post insulator for 33 kv [ galvanized ] ( xiii ) structure for 33 kv hg fuse set ( non galvanised ) ( xiv ) structure for 33 kv hg fuse set [ galvanized ] ( xv ) a swing bus structure ( xvi ) gantry column, girder structures for 33 / 11 kv pss for single transformer [ galvanized ] ( xvii ) a structures for top mounted ab switch on 33 kv bus [ galvanized ] ( xviii ) a structures for top mounted ab switch on 11 kv bus [ galvanized ] ( xix ) a structures for 11 kv take off with top mounted ab switch and provision of lightening arrester [ galvanized ] ( xx ) gi base plate for 33kv ( 500x500x10 mm ) avg weight 19.6kg / plate ( xxi ) stone base plate for 11 kv, dss, lt current and potential transformers ( i ) 33 kv ct outdoor oil immersed type, 3 core, 200 100 / 5 5 1 amp, class 0.5 for differential protection ( ii ) 33 kv ct outdoor oil immersed type, 3 core, 300 150 / 5 5 1 amp, class 0.5 for differential protection ( iii ) 33 kv ct 800 400 / 5 5a, 2 core, 15va , 5p10 for protection, 10va, 0.5 accuracy for metering ( iv ) 33 kv ct 400 200 / 5 5a, 2 core, 15va , 5p10 for protection, 10va, 0.5 accuracy for metering ( v ) 33 kv ct 300 150 / 5 5a, 2 core, 15va , 5p10 for protection, 10va, 0.5 accuracy for metering ( vi ) 33 kv ct 200 100 / 5 5a, 2 core, 15va , 5p10 for protection, 10va, 0.5 accuracy for metering ( vii ) 11 kv ct outdoor oil immersed type, 3 core, 600 300 / 5 5 1amp, class 0.5 for differential protection ( viii ) 11 kv ct 800 400 / 5 5a, 2 core, 15va , 5p10 for protection, 10va, 0.5 accuracy for metering ( ix ) 11 kv ct 400 200 / 5 5a, 2 core, 15va , 5p10 for protection, 10va, 0.5 accuracy for metering ( x ) 11 kv ct 300 150 / 5 5a, 2 core, 15va , 5p10 for protection, 10va, 0.5 accuracy for metering ( xi ) 11 kv ct 200 100 / 5 5a, 2 core, 15va , 5p10 for protection, 10va, 0.5 accuracy for metering ( xii ) 33 / √3 / 110 / √3 / 110 / √3 pt ( core 1:0.5s, core2:3p ) ( xiii ) 11 / √3 / 110 / √3 / 110 / √3 pt ( core 1:0.5s, core2:3p ) power transformer ( i ) 33 / 11 kv power transformer 10 mva copper wound, crgo core ( off load tap changer ) ( ii ) 33 / 11 kv power transformer 10 mva copper wound, crgo core ( on load tap changer ) ( iii ) 33 / 11 kv power transformer 05 mva copper wound, crgo core ( off load tap changer ) ( ivi ) 33 / 11 kv power transformer 05 mva copper wound, crgo core ( on load tap changer ) distribution transformer ( i ) 11 / 0.433 kv distribution transformer 500 kva, copper wound, crgo m4 core onan; bis level 1 ( ii ) 11 / 0.433 kv distribution transformer 500 kva, copper wound, crgo m4 core onan; bis level 2 ( iii ) 11 / 0.433 kv distribution transformer 500 kva, copper wound, crgo m4 core onan; bis level 3 ( iv ) 11 / 0.433 kv distribution transformer 500 kva, copper wound, crgo m4 core onan; bis level 4 ( v ) 11 / 0.433 kv distribution transformer 500 kva, copper wound, crgo m4 core onan; bis level 5 ( vi ) 11 / 0.433 kv distribution transformer 400 kva, copper wound, crgo m4 core onan; bis level 1 ( vii ) 11 / 0.433 kv distribution transformer 400 kva, copper wound, crgo m4 core onan; bis level 2 ( viii ) 11 / 0.433 kv distribution transformer 400 kva, copper wound, crgo m4 core onan; bis level 3 ( ix ) 11 / 0.433 kv distribution transformer 400 kva, copper wound, crgo m4 core onan; bis level 4 ( x ) 11 / 0.433 kv distribution transformer 400 kva, copper wound, crgo m4 core onan; bis level 5 ( xi ) 11 / 0.433 kv distribution transformer 315 kva, copper wound, crgo m4 core onan; bis level 1 ( xii ) 11 / 0.433 kv distribution transformer 315 kva, copper wound, crgo m4 core onan; bis level 2 ( xiii ) 11 / 0.433 kv distribution transformer 315 kva, copper wound, crgo m4 core onan; bis level 3 ( xiv ) 11 / 0.433 kv distribution transformer 315 kva, copper wound, crgo m4 core onan; bis level 4 ( xv ) 11 / 0.433 kv distribution transformer 315 kva, copper wound, crgo m4 core onan; bis level 5 ( xvi ) 11 / 0.433 kv distribution transformer 250 kva, aluminium wound, crgo m4 core onan; bis level 1 ( xvii ) 11 / 0.433 kv distribution transformer 250 kva, aluminium wound, crgo m4 core onan; bis level 2 ( xviii ) 11 / 0.433 kv distribution transformer 250 kva, aluminium wound, crgo m4 core onan; bis level 3 ( xix ) 11 / 0.433 kv distribution transformer 250 kva, aluminium wound, crgo m4 core onan; bis level 4 ( xx ) 11 / 0.433 kv distribution transformer 250 kva, aluminium wound, crgo m4 core onan; bis level 5 ( xxi ) 11 / 0.433 kv distribution transformer 200 kva, aluminium winding, stack type crgo core fitted, completely self protected; bis level 1 ( xxii ) 11 / 0.433 kv distribution transformer 200 kva, aluminium winding, stack type crgo core fitted, completely self protected; bis level 2 ( xxiv ) 11 / 0.433 kv distribution transformer 200 kva, aluminium winding, stack type crgo core fitted, completely self protected; bis level 3 ( xxv ) 11 / 0.433 kv distribution transformer 200 kva, aluminium winding, stack type crgo core fitted, completely self protected; bis level 4 ( xxvi ) 11 / 0.433 kv distribution transformer 200 kva, aluminium winding, stack type crgo core fitted, completely self protected; bis level 5 ( xxvii ) 11 / 0.433 kv distribution transformer 100 kva, aluminium winding, stack type crgo core fitted; bis level 1 ( xxviii ) 11 / 0.433 kv distribution transformer 100 kva, aluminium winding, stack type crgo core fitted; bis level 2 ( xxix ) 11 / 0.433 kv distribution transformer 100 kva, aluminium winding, stack type crgo core fitted; bis level 3 ( xxx ) 11 / 0.433 kv distribution transformer 100 kva, aluminium winding, stack type crgo core fitted; bis level 4 ( xxxi ) 11 / 0.433 kv distribution transformer 100 kva, aluminium winding, stack type crgo core fitted; bis level 5 ( xxxii ) 11 / 0.433 kv distribution transformer 63 kva, aluminium winding, stack type crgo core fitted; bis level 1 ( xxxiii ) 11 / 0.433 kv distribution transformer 63 kva, aluminium winding, stack type crgo core fitted; 4 star bee rating ; bis level 2 ( xxxiv ) 11 / 0.433 kv distribution transformer 63 kva, aluminium winding, stack type crgo core fitted; bis level 3 ( xxxv ) 11 / 0.433 kv distribution transformer 63 kva, aluminium winding, stack type crgo core fitted; bis level 4 ( xxxvi ) 11 / 0.433 kv distribution transformer 63 kva, aluminium winding, stack type crgo core fitted; bis level 5 ( xxxvii ) 11 / 0.433 kv distribution transformer 25 kva, aluminium winding, stack type crgo core fitted; bis level 1 ( xxxviii ) 11 / 0.433 kv distribution transformer 25 kva, aluminium winding, stack type crgo core fitted; bis level 2 ( xxxix ) 11 / 0.433 kv distribution transformer 25 kva, aluminium winding, stack type crgo core fitted; bis level 3 ( xl ) 11 / 0.433 kv distribution transformer 25 kva, aluminium winding, stack type crgo core fitted; bis level 4 ( xli ) 11 / 0.433 kv distribution transformer 25 kva, aluminium winding, stack type crgo core fitted; bis level 5 ( xlii ) 11 / 0.433 kv distribution transformer 16 kva, aluminium winding, stack type crgo core fitted; bis level 1 ( xliii ) 11 / 0.433 kv distribution transformer 16 kva, aluminium winding, stack type crgo core fitted; bis level 2 ( xliv ) 11 / 0.433 kv distribution transformer 16 kva, aluminium winding, stack type crgo core fitted; bis level 3 ( xlv ) 11 / 0.433 kv distribution transformer 16 kva, aluminium winding, stack type crgo core fitted; bis level 4 ( xlvi ) 11 / 0.433 kv distribution transformer 16 kva, aluminium winding, stack type crgo core fitted ; bis level 5 distribution box ( i ) lt distribution box suitable for 500 kva transformer ( 800 a, isolator & 12 sp mccb of 160 a ) ( ii ) lt distribution box suitable for 400 kva transformer ( 600 a, isolator & 9 sp mccb of 160 a ) ( iii ) lt distribution box suitable for 315 kva transformer ( 600 a, isolator & 9 sp mccb of 160 a ) ( iii ) lt distribution box suitable for 200 kva transformer ( 400 a, isolator & 9 sp mccb of 160 a ) ( v ) lt distribution box suitable for 100 kva transformer ( 200 a, isolator & four pole mccb & 6 sp mccb of 120 a ) ( v ) lt distribution box suitable for 63 kva transformer ( 200 a, isolator & four pole mccb & 6 sp mccb of 120 a ) ( vii ) ltdb for 100kva & 63kva, isolator 250a, incoming mccb 4p, 200a, 36ka, outgoing mccb 3p 100a, 36ka ( viii ) ltdb for 25kva, isolator 63a, incoming mccb 4p, 63a, 20ka, outgoing mccb 3p 32a, 20ka ( ix ) lt distribution box suitable for 63 kva transformer ( 200 a, isolator & 6 tp mccb of 100 a ) ( x ) spring loaded cp multi conn bus bar in insulated box single phase 1 in 6 out ( dist. box for fixing on pole suitable for ab xlpe cable ) ( xi ) spring loaded cp multi conn bus bar in insulated box single phase 1 in 9 out ( dist. box for fixing on pole suitable for ab xlpe cable ) ( xii ) spring loaded cp multi conn bus bar in insulated box three phase 1 in 3 out ( dist. box for fixing on pole suitable for ab xlpe cable ) ( xiii ) spring loaded cp multi conn bus bar in insulated box three phase 1 in 5 out ( dist. box for fixing on pole suitable for ab xlpe cable ) ( xiv ) spring loaded cp multi conn bus bar in insulated box three phase 1 in 8 out ( dist. box for fixing on pole suitable for ab xlpe cable ) ( xv ) spring loaded distribution bus bar insulated box for fixing on pole suitable for ab xlpe cable and three phase connection 1 incoming and out going 3 phase connection as per field requirement vcb, c&r panel ( i ) 33 kv vcb, 1250 amp., outdoor type, 26.3 ka for 1 sec rpturing capacty , with cr pannel, & c.t. ratio 1200 600 300 / 1 1a, 2 core, 15va, 5p10 for protection, accuracy 0.5, 10va for metering. pt 33kv / 110v, accuracy class 0.5, va burden 50va, with metering system in panel with numeric relay announciator ( ii ) 33 kv vcb, 1250 amp., outdoor type, 16 ka for 1 sec rpturing capacty , with cr pannel, & c.t. ratio 600 300 / 1 1a or 400 200 / 1 1a, 2 core, 15va, 5p10 for protection, accuracy 0.5, 10va for metering. pt 33kv / 110v, accuracy class 0.5, va burden 50va, ( iii ) 11 kv vcb, outdoor type, 1250 a, 25 ka for 3 sec. rupturing capacity wth c&r panel. ct 1200 600 300 / 5 5a, 2 core, 15va, 5p10 for protection, accuracy 0.5, 10va for metering. p.t. 11 kv / 110v, accuracy class 0.5, 30 va with metering system in panel ( iv ) 11 kv vcb, outdoor type, 800 a, for incoming, 18.4 ka for 1 sec. rupturing capacity with panel ( indoor ) 24 v dc operated with ct 600 300 / 5 5a or 400 200 / 5 5a, 2 core, 15va, 5p10 for protection, accuracy 0.5, 10va for metering. p.t. 33kv / 110v, accuracy class 0.5, 30 va ( v ) 11 kv vcb, outdoor type, 630 a, 25 ka for 3 sec. rupturing capacity wth c&r panel. ct 600 300 / 5 5a or 400 200 / 5 5a, 2 core, 15va, 5p10 for protection, accuracy 0.5, 10va for metering. p.t. 11 kv / 110v, accuracy class 0.5, 30 va ( vi ) 11 kv vcb, outdoor type, 400 a, for outgoing, 18.4 ka for 1 sec. rupturing capacity with panel ( indoor ) 24 v dc operated with ct 600 300 / 5 5a or 400 200 / 5 5a, 2 core, 15va, 5p10 for protection, accuracy 0.5, 10va for metering. p.t. 33kv / 110v, accuracy class 0.5, 30 va ( vii ) indoor type control and relay panel for 33kv, vcb ( feeder breaker ) consisting of a meter, volt meter, relays & accessories complete. ( viii ) indoor type control and relay panel for 33kv, vcb ( transformer breaker ) consisting of a meter, volt meter, relays & accessories complete. ( ix ) indoor type control and relay panel for 11kv, vcb ( transformer breaker ) consisting of a meter, volt meter, relays & accessories complete. ( x ) indoor type control and relay panel for 11kv, vcb ( feeder breaker ) consisting of a meter, volt meter, relays & accessories complete. distribution board ( i ) 415v ac power distribution board ( ii ) 30v dc distribution board pipe connector ( i ) aluminium pipe connector ( ii ) connector pipe to panther ( iii ) connector panther to panther ( iv ) connector panther to ab switch ( v ) connector pipe to pipe ( vi ) connector pipe to dog ( vii ) connector pipe to ab switch ( viii ) connector dog to ab switch copper control cable ( i ) 2.5 mm2 copper 2 core control cable ( armoured ) ( ii ) 2.5 mm2 copper 2 core control cable ( unarmoured ) ( iii ) 2.5 mm2 copper 4 core control cable ( armoured ) ( iv ) 2.5 mm2 copper 4 core control cable ( unarmoured ) ( v ) 2.5 mm2 copper 6 core control cable ( armoured ) ( vi ) 2.5 mm² copper 6 core un armourd cable ( vii ) 7 core x 2.5 sq.mm. armoured control cable ( viii ) 2.5 mm2 copper 8 core control cable ( unarmoured ) ( ix ) 2.5 mm2 copper 10 core control cable ( armoured ) ( x ) 2.5 mm2 copper 10 core control cable ( unarmoured ) ( xi ) 2.5 mm2 copper 12 core control cable ( armoured ) ( xii ) 2.5 mm2 copper 12 core control cable ( unarmoured ) ( xiii ) 19 core x 2.5 sq.mm.armoured control cable capacitor bank ( i ) fully automatic capacitor bank with automatic control panel, isolator, indoor type suitable vacuum circuit breaker, mounting structures etc as required as per technical specifications, drawings, scope of the works of following capacities: ( banks in muiltiple of 600 kvar as per specification ) 3600 kvar ( ii ) 1815 kvar 12.1 kv 3 phase 50 hz outdoor type capacitor bank having step as 363 kvar+726 kvar+726 kvar 12.1 kv bank shall be complete with capacitor units of 121 kvar at 6.98 kv including allied materials such as suitable size of aluminium busbars, pin / pos ( iii ) fully automatic capacitor bank with automatic control panel, isolator, indoor type suitable vacuum circuit breaker, mounting structures etc as required as per technical specifications, drawings, scope of the works of following capacities: ( banks in muiltiple of 600 kvar as per specification ) 1200 kvar ( iv ) 1089 kvar 12.1 kv 3 phase 50 hz outdoor type capacitor bank having step as 363 metering equipment ( i ) 33 kv metering cubicle with pt & ct , 0.5s accuracy class for ct and 0.5s accuracy class for pt of different capacity ( ii ) 33 kv outdoor type oil immersed ct pt combined metering unit 0.5s accuracy class for ct and 0.5s accuracy class for pt of different capacity ( iii ) 33 kv, three phase three wire / three phase four wire, accuracy class 0.2s, dlms compliant abt meter ( modular rack mounted ) of different capacity ( iv ) 33 kv, three phase three wire / three phase four wire, accuracy class 0.2s, dlms compliant abt meter ( projection type ) of different capacity ( v ) 33 kv / 110 v, three phase four wire, ( 0.2s accuracy class for ct and 0.2 accuracy class for pt ) , ratio 1600 / 1a or 1200 / 1a ct pt combined metering unit for feeder ( vi ) metering panel, data concentrator unit ( dcu ) with modem ( vii ) structure for 33 kv metering unit ( viii ) ht electronic trivector static meter, 3 phase 4 wire, accuracy class 0.2s ( – / 110v & – / 5a ) ( dlms complaint ) with compatible gprs modem with meter box ( ix ) ht electronic trivector static meter, 3 phase 4 wire, accuracy class 0.5s ( – / 110v & – / 5a ) ( dlms complaint ) with compatible gprs modem with meter box ( x ) trivector energy meter of 800 / 5 amp ( xi ) trivector energy meter of 400 / 5 amp ( xii ) 11 kv, outdoor type oil immersed ct pt combined metering unit, 3 phase 4 wire ( 11kv / 110v ) [ 12 kv pt 50va burden 0.5s accuracy class; ct 20 / 5a, 30 / 5a, 60 / 5a, 100 / 5a, 200 / 5a, 400 / 5a, 15 va, 0.5 accuracy class ] ( xiii ) 11 kv metering cubicle with pt ratio 11kv / √3 / 110v and ct ratio 20 / 5a, 30 / 5a, 60 / 5a, 100 / 5a, 200 / 5a, 400 / 5a, 0.5 accuracy class for both ( xiv ) ltct electronic meter ( 200 / 150 / 100 / 5 ) 3 phase 4 wire with meter box, class 0.5s accuracy ( xv ) ac 3 phase, 4 wire, 40 200amp lt electronic trivector accuracy class 1.0 dlms compliant category a meter with inbuilt cts and inbuilt 4g with fall back option gprs modem ( xvi ) structure for d.t meter ( xvii ) ac 3 phase dtr meter complete set above 100kva 400 / 5a ( xviii ) lt electronic trivector meter 40 200 amp. ( xix ) 11 kv / 110, 3 phase 4 wire accuracy class dlms compliant trivector energy meter ratio 200 / 5a ( xx ) 11 kv / 110, 3 phase 4 wire accuracy class dlms compliant trivector energy meter ratio 400 / 5a ( xxi ) 11 kv / 110, 3 phase 4 wire accuracy class dlms compliant trivector energy meter ratio 600 / 5a ( xxii ) 33 kv / 110, 3 phase 4 wire accuracy class dlms compliant trivector energy meter ratio 400 / 1a ( xxiii ) 33 kv / 110, 3 phase 4 wire accuracy class dlms compliant trivector energy meter ratio 600 / 1a ( xxiv ) 33kv / 110v , 3 phase, 4 wire , accuracy class 0.5 ct pt, combined metering unit for feeder, ratio 400 / 1a ( xxv ) 11kv / 110, 3 phase, 4 wire , accuracy class 0.5 ct pt, combined metering unit for feeder, ratio 400 / 5a ( xxvi ) 11 kv / 110 v 3 phase 4 wire accuracty class 0.5 ct pt combined metering unit for feeder, ratio 200 / 5 a ( xxvii ) 33kv / 110v , 3 phase, 4 wire , accuracy class 0.5 ct pt, combined metering unit for feeder, ratio 600 / 1a ( xxviii ) 11 kv / 110, 3 phase 4 wire accuracty class 0.5 ct pt combined metering unit for feeder, ratio 600 / 5 a ( xxix ) dlms compliant, single phase 2 wire 5 30 amp. 1.0 accuracy, class ac statics single phase meter with meter box ( xxx ) lt static energy meter, 3 phase 4 wire, direct connected, 100 amp. with meter box, class 1.0 accuracy ( xxxi ) three phase 4 wire ac static whole current meter, electronic energy meter with box ( 10 60 ) amp ( xxxii ) single phase electronic meter, two wire, 5 30 amp. class 1.0 accuracy with box ( xxxiii ) single phase rf meter with box as per is 13779 standards, dlms compliant ( xxxiv ) three phase rf meter with box as per is 13779 standards, dlms compliant ( xxxv ) single phase rs 232 / 485 prepaid energy meter ( xxxvi ) three phase rs 232 / 485 prepaid energy meter ( xxxvii ) single phase rf prepaid energy meter ( xxxviii ) three phase rf prepaid energy meter ( xxxix ) single phase gprs / gsm prepaid energy meter ( xl ) three phase gprs / gsm prepaid energy meter ( xli ) pvc cable gland sizes 20 mm, ( xlii ) pvc cable gland sizes 25 mm, ( xliii ) pvc cable gland sizes 32 mm ( xliv ) pvc cable gland sizes 40 mm ( xlv ) pvc cable gland sizes 50 mm ( xlvi ) pvc cable gland sizes 63 mm ( xlvii ) pvc cable gland sizes 75 mm ( xlviii ) single phase whole current smart meter ( 5 30 amp ) with rf communication module ( excl. nic card ) incl. polycarbonate meter box ( xlix ) three phase whole current smart meter ( 10 50 amp ) with rf communication module ( excl. nic card ) incl. polycarbonate meter box ( l ) three phase whole current smart meter ( 20 100 amp ) with rf communication module ( excl. nic card ) incl. polycarbonate meter box ( li ) lt three phase ct operated smart tri vector meter with rf communication module ( excl. nic card ) for consumer incl. smc double chambered meter box with embeded ct ( ct ratio 100 / 5 amp ) ( lii ) lt three phase ct operated smart tri vector meter with rf communication module ( excl. nic card ) for consumer incl. smc double chambered meter box with embeded ct ( ct ratio 200 / 5 amp ) ( liii ) lt three phase ct operated smart tri vector meter with rf communication module ( excl. nic card ) for consumer incl. smc double chambered meter box with embeded ct ( ct ratio / 5 amp ) ( liv ) ht three phase ct operated smart tri vector meter with rf communication module ( excl. nic card ) for feeder ( ct raio / 5amp ) ( lv ) ht three phase ct operated smart tri vector meter with rf communication module ( excl. nic card ) for consumer incl. meter box ( ct raio / 5amp ) ( lvi ) field routers / collectors / dcu along with installation clamp and accessories complete ( lvii ) network interface card ( nic ) for smart meter ( lviii ) centralized management console with single 24 led monitor ( lix ) work station consoles with dual 24 led monitor along with operating system, antivirus & license ( lx ) network laserjet ( b / w ) photocopy, scanning and printing ( lxi ) a4 size inkjet / bubble jet printer ( lxii ) a3 size inkjet color printer / all in one color laserjet printer ( lxii ) l.t. ct ratio 50 / 5a, 5va, 0.5 accuracy for metering, epoxy casted ( lxii ) l.t. ct ratio 100 / 5a, 5va, 0.5 accuracy for metering, epoxy casted ( lxii ) l.t. ct ratio 200 / 5a, 5va, 0.5 accuracy for metering, epoxy casted ( lxii ) l.t. ct ratio 300 / 5a, 5va, 0.5 accuracy for metering, epoxy casted ( lxii ) l.t. ct ratio 400 / 5a, 5va, 0.5 accuracy for metering, epoxy casted ( lxii ) l.t. ct ratio 500 / 5a, 5va, 0.5 accuracy for metering, epoxy casted ( lxii ) l.t. ct ratio 600 / 5a, 5va, 0.5 accuracy for metering, epoxy casted ( lxii ) l.t. ct ratio 800 / 5a, 5va, 0.5 accuracy for metering, epoxy casted gi service pipe ( i ) gi service pipe 25 mm diameter 3 mtr length ( ii ) gi service pipe 40 mm diameter 3 mtr length ( iii ) gi service pipe 60mm diameter 3 mtr length ( iv ) g.i. pipe 3 dia ring main units ( i ) 11 kv 3 way rmu, 2od + 1vl, one incomer + one breaker + one outgoing ( ii ) 11 kv 4 way rmu, 2od + 2vl, ( one incomer + two breakers + one outgoing ( iii ) 11 kv 5 way rmu, 2od + 3vl, ( one incomer + three breakers + one outgoing ) ( iv ) 11 kv 6 way rmu, 2od + 4vl, ( one incomer + four breakers + one outgoing xlpe insulated cables ( i ) 33 kv ht xlpe cable single core 630mm2 ( armoured ) ( ii ) 1c x 400mm2 cable ( 33 kv power cable ) ( iii ) 33 kv ht xlpe cable 3 core 400 sq mm ( armoured ) ( iv ) 33 kv ht xlpe cable 3 core 300mm2 ( armoured ) ( v ) 33 kv ht xlpe cable 3 core 240mm2 ( armoured ) ( vi ) 33 kv ht xlpe cable 3 core 185mm2 ( armoured ) ( vii ) 33 kv ht xlpe cable 3 core 150mm2 ( armoured ) ( viii ) 33 kv ht xlpe cable 3 core 120mm2 ( armoured ) ( ix ) 33 kv ht xlpe cable 3 core 95mm2 ( armoured ) ( x ) 33 kv ht xlpe cable 3 core 70mm2 ( armoured ) ( xi ) 33 kv ht xlpe cable 3 core 50mm2 ( armoured ) ( xii ) 11 kv 3 core x 35 sq. mm cable ( armoured ) ( xiii ) 11 kv xlpe cable single core 630mm2 ( armoured ) ( xiv ) 3core x 630sq mm ( 11 kv power cable ) ( xv ) 11 kv xlpe cable 3 core 400mm2 ( armoured ) ( xvi ) 11 kv xlpe cable 3 core 300mm2 ( armoured ) ( xvii ) 11 kv xlpe cable 3 core 240 mm2 ( armoured ) ( xviii ) 11 kv xlpe cable 3 core 185mm2 ( armoured ) ( xix ) 11 kv xlpe cable 3 core 150mm2 ( armoured ) ( xx ) 11 kv xlpe cable 3 core 120mm2 ( armoured ) ( xxi ) 11 kv xlpe cable 3 core 95mm2 ( armoured ) ( xxii ) 11 kv xlpe cable 3 core 70mm2 ( armoured ) ( xxiii ) 11 kv xlpe cable 3 core 50mm2 ( armoured ) ( xxiv ) 11 kv xlpe cable 3 core 25mm2 ( armoured ) ( xxv ) power cable for dt meter 120 sq.mm unarmoured ( xxvi ) power cable for dt meter 240 sq.mm unarmoured ( xxvii ) lt xlpe cable 4 core 16 mm2 ( armoured ) ( xxviii ) lt xlpe cable 4 core 16mm2 ( unarmoured ) ( xxix ) lt xlpe cable 4 core 25mm2 ( armoured ) ( xxx ) lt xlpe cable 3.5 core 300mm2 ( armoured ) ( xxxi ) lt xlpe cable 3.5 core 185mm2 ( armoured ) ( xxxii ) lt xlpe cable 3.5 core 120mm2 ( armoured ) ( xxxiii ) lt xlpe cable 3.5 core 95 mm2 ( armoured ) ( xxxiv ) lt xlpe cable 3.5 core 50mm2 ( armoured ) ( xxxv ) lt xlpe cable 3.5 core 25mm2 ( armoured ) ( xxxvi ) lt xlpe cable 2 core 16 mm2 ( armoured ) ( xxxvii ) lt xlpe cable 2 core 10mm2 ( armoured ) ( xxxviii ) lt xlpe cable 2 core 6mm2 ( armoured ) ( xxxix ) lt xlpe cable 1cx120 sqmm ( armoured ) ( xl ) lt xlpe single core cable 95 mm2 ( armoured ) ( xli ) lt xlpe single core cable 50 mm2 ( armoured ) ( xlii ) lt xlpe single core cable 25 mm2 ( armoured ) ( xliii ) lt xlpe cable 3.5 core 35 sq. mm. ( armoured ) ( xliv ) lt xlpe cable 3.5 core 70 sq. mm. ( armoured ) ( xlv ) lt xlpe single core unarmoured 1 x 400 sqmm pvc insulated cables ( i ) 3.5 core 300 sq. mm armoured, stranded aluminium conductor, pvc insulated and pvc sheathed cable ( ii ) 3.5 core 240 sq. mm armoured, stranded aluminium conductor, pvc insulated and pvc sheathed cable ( iii ) 3.5 core 185 sq. mm armoured, stranded aluminium conductor, pvc insulated and pvc sheathed cable ( iv ) 3.5 core 150 sq. mm armoured, stranded aluminium conductor, pvc insulated and pvc sheathed cable ( v ) 3.5 core 70 sq. mm armoured, stranded aluminium conductor, pvc insulated and pvc sheathed cable ( vi ) 3.5 core 35 sq. mm armoured, stranded aluminium conductor, pvc insulated and pvc sheathed cable ( vii ) 2 core 16 sq. mm armoured, stranded aluminium conductor, pvc insulated and pvc sheathed cable ( viii ) 1 core 120 sq. mm unarmoured, stranded aluminium conductor, pvc insulated and pvc sheathed cable ( ix ) lt pvc cable 3.5 core 95 mm2 ( armoured ) ( x ) lt pvc cable 3.5 core 10 mm2 ( armoured ) ( xi ) lt pvc cable 3.5 core 6 mm2 ( armoured ) ( xii ) lt pvc cable 2 core 16 mm2 ( armoured ) ( xiii ) lt pvc cable 2 core 10 mm2 ( armoured ) ( xiv ) lt pvc cable 2 core 6 mm2 ( armoured ) ( xv ) lt pvc cable 2 core 4 mm2 ( armoured ) ( xvi ) lt pvc cable 1 core 16 mm2 ( armoured ) ( xvii ) lt pvc cable 1 core 50 mm2 ( armoured ) ( xviii ) lt pvc cable 1 core 70 mm2 ( armoured ) ( xix ) lt pvc cable 1 core 150 mm2 ( armoured ) ( xx ) lt pvc cable 1 core 300 mm2 ( armoured ) ( xxi ) pvc single phase service cable 3.5 core 25 mm2 ( amoured ) ( xxii ) 2.5 sq mm twin core pvc service cable ( armoured ) ( xxiii ) 4 sq mm twin core pvc service cable ( unarmoured ) ( xxiv ) pvc single phase service cable 2 core 2.5 mm2 ( unamoured ) ( xxv ) pvc single phase service cable 2 core 6 mm2 ( unarmoured ) ( xxvi ) pvc three phase service cable 4 core 6 mm2 ( armoured ) ( xxvii ) pvc three phase service cable 4 core 8 mm2 ( armoured ) ( xxviii ) pvc three phase service cable 4 core 10 mm2 ( armoured ) ( xxix ) pvc three phase service cable 4 core 16 mm2 ( armoured ) ( xxx ) pvc three phase service cable 4 core 25 mm2 ( armoured ) ( xxxi ) pvc three phase service cable 4 core 10 mm2 ( unarmoured ) aerial bunched cables ( i ) 11 kv xlpe ht ab cable 3cx185mm2+240mm2 bare messenger ( ii ) 11 kv xlpe ht ab cable 3cx185mm2+150mm2 bare messenger ( iii ) 11 kv xlpe ht ab cable 3cx150mm2+120mm2 bare messenger ( iv ) 11kv xlpe ht ab cable 3cx120 mm2 + 95mm2 bare messenger ( v ) 11 kv xlpe ht ab cable 3cx95mm2+80mm2 bare messenger ( vi ) 11 kv xlpe ht ab cable 3cx70mm2+70mm2 bare messenger ( vii ) 11 kv xlpe ht ab cable 3cx50mm2+70mm2 bare messenger ( viii ) 11 kv xlpe ht ab cable 3cx35mm2+70mm2 bare messenger ( ix ) 11 kv xlpe ht ab cable 3cx35mm2+35mm2 bare messenger ( x ) lt xlpe ab cable 3cx120+1cx70+1cx16 mm2 ( xi ) lt xlpe ab cable 3cx95 sqmm + 1x70 sqmm+1x70 sq mm ( xii ) lt xlpe ab cable 3cx95+1cx70+1cx16 mm2 ( xiii ) lt xlpe ab cable 3x70+1x50+1x16 ( street light ) mm2 ( xiv ) lt xlpe ab cable 3cx50 sqmm + 1x35 sqmm+1x16 sq mm ( xv ) lt xlpe ab cable 3x50+1x25+1x35 mm2 ( xvi ) lt xlpe ab cables 1x16 ( ph ) + 1x25 ( bare condustor + 1x16 ( insulated street lighting ) mm2 ( xvii ) lt xlpe ab cable 3cx120+70mm2 ( xviii ) lt xlpe ab cable 3cx95+70mm2 ( xix ) lt xlpe ab cable 3cx50+35mm2 ( xx ) lt xlpe ab cable 3cx35+25mm2 ( xxi ) lt xlpe ab cable 3cx25+25mm2 ( xxii ) lt xlpe ab cable 3cx16+25mm2 ( xxiii ) lt xlpe ab cable 1cx16+25mm2 single phase ab cable accessories ( i ) 11 kv ab cable straight thru joint kit suitable for 35 70 sqmm ( ii ) 11 kv ab cable straight thru joint kit suitable for 95 120 sqmm ( iii ) 11 kv abc termination kit 35 70 sqmm ( iv ) 11 kv abc termination kit 95 120 sqmm ( v ) lt pre insulated mid span joint suitable 25 mm2 phases ( vi ) lt pre insulated mid span joint suitable 35 mm2 phases ( vii ) lt pre insulated mid span joint suitable 50 mm2 phases ( viii ) lt pre insulated mid span joint suitable 70 mm2 phases ( ix ) lt pre insulated mid span joint suitable 95 mm2 phases ( x ) lt pre insulated mid span joint suitable 120 mm2 phases ( xi ) pre insulated mid span joint suitable for 25 mm2 neutral messenger ( xii ) pre insulated mid span joint suitable for 35 mm2 neutral messenger ( xiii ) pre insulated mid span joint suitable for 50 mm2 neutral messenger ( xiv ) insulation piercing connector for db charging ( xv ) insulation piercing connector branching suitable for t joints ( xvi ) piercing connector for lt ab cable ( xvii ) insulation piercing connector type i ( main 16 95 mm2 & tap 4 50 mm2 ) ( xviii ) insulation piercing connector type ii ( main 16 120 mm2 & tap 16 120 sq mm ) ( xix ) satellite connector ( xx ) lt ab cable accessory, 1.1mtr. stainless steel strap if207 ( 20x0.7 ) ( xxi ) buckle for strap ( xxii ) suspension clamp with eyehook ( xxiii ) suspension clamp suitable for 25 70 sqmm baremessenger ( including 1 no. suspension clamp with bracket + 1.5 mtr ss strap + 2 nos. ss buckle ) ( xxiv ) suspension clamp suitable for 35 95 sqmm bare messenger ( including 1 no. suspension clamp with bracket + 1.5 mtr ss strap + 2 nos. ss buckle ) ( xxv ) suspension clamp suitable for 95 150 sqmm bare messenger ( including 1 no. suspension clamp with bracket + 1.5 mtr ss strap + 2 nos. ss buckle ) ( xxvi ) dead end clamp with eyehook ( xxvii ) dead end clamp suitable for 25 70 sqmm bare messenger ( including 1 no. dead end bracket + 1 no. dead end + 1.5 mtr ss strap + 2 nos. ss buckle ) ( xxviii ) dead end clamp suitable for 70 95 sqmm bare messenger ( including 1 no. dead end bracket + 1 no. dead end + 1.5 mtr ss strap + 2 nos. ss buckle ) ( xxix ) dead end clamp suitable for 95 150 sqmm bare messenger ( including 1 no. dead end bracket + 1 no. dead end + 1.5 mtr ss strap + 2 nos. ss buckle ) ( xxx ) dead end clamp assembly suitable upto 25 sq.mm bare messenger ( 01 dead end clamp with bracket, 2 mtr. stainless steel straps, 02 nos. buckles ) ( xxxi ) suspension clamp assembly suitable for 95 mm2 bare messenger ( 01 nos. suspension clamp with bracket, 2 mtr. stainless stell straps 02 nos. buckles ( xxxii ) service main anchor clamp for proper support of service cable ( 4mm2 and 10 mm2 ) ( xxxiii ) eye hook ( xxxiv ) stainless steel strip of 20mmx1mmx1000mm with buckle clip fabricated items ( i ) hot dip galvanized fabricated iron material for 33 kv line, lt line & dss ( ii ) 33 kv pole top bracket 50x10 mm flat [ galvanized ] ( 2.5 kgs. ) ( iii ) 33 kv pole top bracket 65x65x6 mm [ galvanized ] ( 3.58 kgs. ) ( iv ) 33 kv pole top bracket [ non galvanized ] ( 2.9 kgs. ) ( v ) 11kv pole top bracket 50x8 mm [ galvanized ] ( 2.2 kgs. ) ( vi ) 11 kv pole top bracket 50x8 mm ( f type ) [ non galvanized ] ( 2.2 kgs, ) ( vii ) 11 kv f clamp / bracket ( 2.1 kgs. ) ( viii ) 11 kv fish plate ( 1.6 kgs. ) ( ix ) 33 kv fish plate ( for st pole 13 mtr. ) ( 3 kgs, ) ( x ) 33kv v cross arm for ( 100x50x6 mm ) [ galvanized ] ( 19.7 kgs. ) ( xi ) 33 kv v cross arm ( 100x 50x 6 mm ) [ non galvanized ] ( 19.7 kgs. ) ( xii ) 33 kv dp special type v cross arm [ galvanised ] ( 21 kgs. ) ( xiii ) 11kv v cross arm ( 100x50x6 mm ) , [ galvanized ] ( 16 kgs. ) ( xiv ) 11kv v cross arm ( 75x40x6 mm ) , [ galvanized ] ( 14.6 kgs. ) ( xv ) 11 kv v cross arm ( 75 x 40 x6 mm ) [ non galvanized ] ( 14.6 kgs. ) ( xvi ) ms angle ( 65x65x6 mm ) for guarding of 33 kv [ galvanized ] ( 16 kgs. ) ( xvii ) ms angle ( 65x65x6 mm ) for guarding of 11 kv [ galvanized ] ( 13.6 kgs. ) ( xviii ) ms angle ( 65x65x6 mm ) for guarding of 33 kv, 11 kv, l.t line [ non galvanized ] ( 13.6 kgs. ) ( xix ) top channel set ( 100x50x6 mm ) 3200 mm length [ galvanized ] ( 66.2 kgs. ) ( xx ) top channel set ( 100x50x6 mm ) [ non galvanized ] ( 66.2 kgs. ) ( xxi ) ms channel for ab switch ( 100x50x6 mm ) [ galvanized ] ( 28.16 kgs. ) ( xxii ) ms channel ab switch ( 100x50x6 mm ) [ non galvanized ] ( 28.16 kgs. ) ( xxiii ) 33kv d p channel ( 100x50x6 mm ) 3150 mm long [ galvanized ] ( 65.2 kgs. ) ( xxiv ) 33kv d p channel ( 100x50x6 mm ) 2200 mm long [ galvanized ] ( 45.5 kgs. ) ( xxv ) 33kv d p channel ( 100x50x6 mm ) 1.3 meter long [ galvanized ] ( 26.9 kgs. ) ( xxvi ) 33 kv d.p channel ( 100x50x6 mm ) 1.3 meter [ non galvanized ] ( 26.9 kgs. ) ( xxvii ) 11kv d p channel ( 75x40x6 mm ) [ galvanized ] ( 41.3 kgs. ) ( xxviii ) 11kv d.p channel ( 75x40x6mm ) [ non galvanized ] ( 41.3 kgs. ) ( xxix ) transformer base channel ( 100x50x6 mm ) [ galvanized ] ( 52.63 kgs. ) ( xxx ) transformer base channel ( 100x50x6 mm ) [ non galvanized ] ( 52.63 kgs. ) ( xxxi ) transformer belting ( 50x50x6 mm ) & belting support ( 40x40x6 mm ) [ galvanized ] ( 52.3 kgs. ) ( xxxii ) transformer belting ( 50x50x6 mm ) & belting support ( 40x40x6 mm ) [ non galvanized ] ( 52.3 kgs. ) ( xxxiii ) belting angle a ( 65x65x6 mm ) [ galvanized ] ( 31 kgs. ) ( xxxiv ) belting angle b ( 65x65x6 mm ) [ galvanized ] ( 28 kgs. ) ( xxxv ) back clamp ( 50x6 mm ) for v xrm & & top bracket for 13 mtr. stp [ galvanized ] ( 3.2 kgs. ) ( xxxvi ) back clamp ( 50x8 mm ) for guarding angle for 13 mtr. stp [ galvanized ] ( 3.2 kgs. ) ( xxxvii ) back clamp ( 50x8 mm ) for guarding angle for 9 mtr. psc pole [ galvanized ] ( 3 kgs. ) ( xxxviii ) back clamp ( 50x6 mm ) for 60kg rail pole [ galvanized ] ( 3.2 kgs. ) ( xxxix ) back clamp ( 50x6 mm ) for 60kg rail pole [ non galvanized ] ( 3.2 kgs. ) ( xl ) back clamp ( 50x8 mm ) for v xrm & top bracket for 9 mtr 400kg psc pole [ galvanized ] ( 3 kgs. ) ( xli ) back clamp ( 50x6 mm ) for v arm & top bracket 9 mtr 400kg psc pole [ galvanized ] ( 3 kgs. ) ( xlii ) back clamp ( 50x6 mm ) for 9mtr 400kg psc pole [ non galvanized ] ( 3 kgs. ) ( xliii ) back clamp ( 50x6 mm ) for 8 mtr 200kg psc pole [ galvanized ] ( 2.8 kgs. ) ( xliv ) back clamp ( 50x6 mm ) for 8 mtr 200kg psc pole [ non galvanized ] ( 2.8 kgs. ) ( xlv ) back clamp ( 50x6 mm ) for tublar pole [ galvanized ] ( 2 kgs. ) ( xlvi ) back clamp ( 50x6 mm ) for tublar pole [ non galvanized ] ( 2 kgs. ) ( xlvii ) support clamp for v cross arm for 60kg rail pole [ galvanized ] ( 1.6 kgs. each ) ( xlviii ) support clamp for v cross arm for 60kg rail pole [ non galvanized ] ( 1.6 kgs. each ) ( xlix ) support clamp for v cross arm for 9 mtr 400kg psc pole [ galvanized ] ( 1.2 kgs. each ) ( l ) support clamp for v cross arm for 9 mtr 400kg psc pole [ non galvanized ] ( 1.2 kgs. each ) ( li ) support clamp for v cross arm for 8 mtr 200kg psc pole [ galvanized ] ( 1.08 kgs. each ) ( lii ) support clamp for v cross arm for 8 mtr 200kg psc pole [ non galvanized ] ( 1.08 kgs. each ) ( liii ) support clamp for v cross arm for tublar pole [ galvanized ] ( 1.4 kgs. each ) ( liv ) support clamp for v cross arm for tublar pole [ non galvanized ] ( 1.4 kgs. each ) ( lv ) back clamp a for belting angle ( 50x8 ) ( 1.872 kgs. each ) ( lvi ) back clamp b for belting angle ( 50x8 ) ( 1.872 kgs. each ) ( lvii ) back clamp for 33 kv dp special type v cross arm [ galvanised ] ( 3 kgs. each ) ( lviii ) back clamp ( 50x6 mm ) jointing / packing piece for 60kg rail pole [ galvanized ] ( 3.7 kgs. ) ( lix ) back clamp ( 50x6 mm ) jointing / packing piece for 60kg rail pole [ non galvanized ] ( 3.7 kgs. ) ( lx ) clamp for top channel 50x6 mm flat for 60kg rail pole [ galvanized ] ( 2.8 kgs. ) ( lxi ) clamp for top channel 50x6 mm flat for 60kg rail pole [ non galvanized ] ( 2.8 kgs. ) ( lxii ) clamp for top channel 50x6 mm flat for 9 mtr 400kg psc pole [ galvanized ] ( 3 kgs. ) ( lxiii ) clamp for top channel 50x6 mm flat for 9 mtr 400kg psc pole [ non galvanized ] ( 3 kgs. ) ( lxiv ) clamp for top channel 50x6 mm flat for 8 mtr 200kg psc pole [ galvanized ] ( 2.8 kgs. ) ( lxv ) clamp for top channel 50x6 mm flat for 8 mtr 200kg psc pole [ non galvanized ] ( 2.8 kgs. ) ( lxvi ) clamp for top channel 50x6 mm flat for tublar pole [ galvanized ] ( 2 kgs. ) ( lxvii ) clamp for top channel 50x6 mm flat for tublar pole [ non galvanized ] ( 2 kgs. ) ( lxviii ) clamp for ab switch base channel ( 50x6 mm ) for 60kg rail pole [ galvanized ] ( 2.4 kgs. ) ( lxix ) clamp for ab switch base channel ( 50x6 mm ) for 60kg rail pole [ non galvanized ] ( 2.4 kgs. ) ( lxx ) clamp for ab switch base channel ( 50x6 mm ) for 9 mtr 400kg psc pole [ galvanized ] ( lxxi ) clamp for ab switch base channel ( 50x6 mm ) for 9 mtr 400kg psc pole [ non galvanized ] ( lxxii ) clamp for ab switch base channel ( 50x6 mm ) for 8 mtr 200kg psc pole [ galvanized ] ( lxxiii ) clamp for ab switch base channel ( 50x6 mm ) for 8 mtr 200kg psc pole [ non galvanized ] ( lxxiv ) clamp for ab switch base channel ( 50x6 mm ) for tublar pole [ galvanized ] ( lxxv ) clamp for ab switch base channel ( 50x6 mm ) for tublar pole [ non galvanized ] ( lxxvi ) ms channel ( 75x40x6 mm ) for supporting h.g fuse & l.a [ galvanized ] ( 19.3 kgs. ) ( lxxvii ) ms channel ( 75x40x6 mm ) for supporting h.g fuse & l.a [ non galvanized ] ( 19.3 kgs. ) ( lxxviii ) clamp ( 50 x 6 mm ) for transformer base channel [ galvanized ] ( 3.2 kgs. ) ( lxxix ) clamp ( 50 x 6 mm ) for transformer base channel [ non galvanized ] ( 3.2 kgs. ) ( lxxx ) clamp ( 50 x 6 mm ) for transformer belting [ galvanized ] ( 1.872 kgs. ) ( lxxxi ) clamp ( 50 x 6 mm ) for transformer belting [ non galvanized ] ( 1.872 kgs. ) ( lxxxii ) clamp ( 50 x 6 mm ) for lt bus & h.g fuse set [ galvanized ] ( 1.872 kgs. ) ( lxxxiii ) clamp ( 50 x 6 mm ) for lt bus & h.g fuse set [ non galvanized ] ( 1.872 kgs. ) ( lxxxiv ) d p channel support clamp ( 50x6 mm ) feet ( 1 pair = 1 set ) for 60kg rail pole [ galvanized ] ( 2.25 kgs. each ) ( lxxxv ) d.p channel support clamp ( 50x6 mm ) ) for 60kg rail pole [ non galvanized ] ( 2.25 kgs. each ) ( lxxxvi ) d p channel support clamp ( 50x6 mm ) feet ( 1 pair = 1 set ) for 9 mtr 400kg psc pole [ galvanized ] ( 1.5 kgs. each ) ( lxxxvii ) d.p channel support clamp ( 50x6 mm ) for 9 mtr 400kg psc pole [ non galvanized ] ( 1.5 kgs. each ) ( lxxxviii ) d p channel support clamp ( 50x6 mm ) feet ( 1 pair = 1 set ) for 8 mtr 200kg psc pole [ galvanized ] ( 1.1 kgs. each ) ( lxxxix ) d.p channel support clamp ( 50x6 mm ) for 8 mtr 200kg psc pole [ nongalvanized ] ( 1.1 kgs. each ) ( xc ) d p channel support clamp ( 50x6 mm ) feet ( 1 pair = 1 set ) for tublar pole [ galvanized ] ( 4.5 kgs. each ) ( xci ) d p channel support clamp ( 50x6 mm ) feet ( 1 pair = 1 set ) for tublar pole [ non galvanized ] ( 4.5 kgs. each ) ( xcii ) d p channel clamp ( 40x6 mm ) flat for 60 kg rail pole [ galvanized ] ( 1.92 kgs. ) ( xciii ) d p channel clamp ( 40x6 mm ) flat for 60 kg rail pole [ non galvanized ] ( 1.92 kgs. ) ( xciv ) d p channel clamp ( 40x6 mm ) flat 9 mtr 400kg psc pole [ galvanized ] ( 1.92 kgs. ) ( xcv ) d p channel clamp ( 40x6 mm ) flat 9 mtr 400kg psc pole [ non galvanized ] ( 1.92 kgs. ) ( xcvi ) d p channel clamp ( 40x6 mm ) flat 8 mtr 200kg psc pole [ galvanized ] ( 1.08 kgs. ) ( xcvii ) d p channel clamp ( 40x6 mm ) flat 8 mtr 200kg psc pole [ non galvanized ] ( 1.08 kgs. ) ( xcviii ) d p channel clamp ( 40x6 mm ) flat for tublar pole [ galvanized ] ( 1.8 kgs. ) ( xcix ) d p channel clamp ( 40x6 mm ) flat for tublar pole [ non galvanized ] ( 1.8 kgs. ) ( c ) 33kv cross bracing for d p structure ( 50x50x6 ) [ galvanized ] ( 64.3 kgs. ) ( ci ) 33 kv cross bracing for dp channel [ non galvanized ] ( 64.3 kgs. ) ( cii ) 11 kv cross bracing for d p structure [ galvanized ] ( 51.7 kgs. ) ( ciii ) 11 kv cross bracing for d p structure [ non galvanized ] ( 51.7 kgs. ) ( civ ) clamp for cross bracing set of 2 pair for 60kg rail pole [ galvanized ] ( 1.872 kgs. each ) ( cv ) clamp for cross bracing set of 2 pair for 60kg rail pole [ non galvanized ] ( 1.872 kgs. each ) ( cvi ) clamp for cross bracing set of 2 pair for 9 mtr 400kg psc pole [ galvanized ] ( 1.3 kgs. ) ( cvii ) clamp for cross bracing set of 2 pair for 9 mtr 400kg psc pole [ non galvanized ] ( 1.3 kgs. ) ( cviii ) clamp for cross bracing set of 2 pair for 8 mtr 200kg psc pole [ galvanized ] ( 1.2 kgs. ) ( cix ) clamp for cross bracing set of 2 pair for 8 mtr 200kg psc pole non [ galvanized ] ( 1.2 kgs. ) ( cx ) clamp for cross bracing set of 2 pair for tublar pole [ galvanized ] ( 1.75 kgs. ) ( cxi ) clamp for cross bracing set of 2 pair for tublar pole [ non galvanized ] ( 1.75 kgs. ) ( cxii ) support clamp for cross bracing for 60kg rail pole [ galvanized ] ( 2.5 kgs. each ) ( cxiii ) support clamp for cross bracing for 60kg rail pole [ non galvanized ] ( 2.5 kgs. each ) ( cxiv ) support clamp for cross bracing for 9 mtr 400kg psc pole [ galvanized ] ( 2.33 kgs. each ) ( cxv ) support clamp for cross bracing for 9 mtr 400kg psc pole [ non galvanized ] ( 2.33 kgs. each ) ( cxvi ) support clamp for cross bracing for 8 mtr 200kg psc pole [ galvanized ] ( 1.68 kgs. each ) ( cxvii ) support clamp for cross bracing for 8 mtr 200kg psc pole [ non galvanized ] ( 1.68 kgs. each ) ( cxviii ) support clamp for cross bracing for tublar pole [ galvanized ] ( 2.1 kgs. each ) ( cxix ) support clamp for cross bracing for tublar pole [ non galvanized ] ( 2.1 kgs. each ) ( cxx ) angle / side stay clamp ( 50x8 mm ) for 13 mtr. stp pole [ galvanized ] ( 2.1 kgs. ) ( cxxi ) angle / side stay clamp ( 50x6 mm ) for 60kg rail pole [ galvanized ] ( 1.92 kgs. ) ( cxxii ) angle / side stay clamp ( 50x6 mm ) for 60kg rail pole [ non galvanized ] ( 1.92 kgs. ) ( cxxiii ) angle / side stay clamp ( 50x10 mm ) for 9 mtr 400kg psc pole [ galvanized ] ( 1.92 kgs. ) ( cxxiv ) angle / side stay clamp ( 50x10 mm ) for 9 mtr 400kg psc pole [ non galvanized ] ( 1.92 kgs. ) ( cxxv ) angle / side stay clamp ( 50x6 mm ) for 8 mtr 200kg psc pole [ galvanized ] ( 1.08 kgs. ) ( cxxvi ) angle / side stay clamp ( 50x6 mm ) for 8 mtr 200kg psc pole [ non galvanized ] ( 1.08 kgs. ) ( cxxvii ) angle / side stay clamp ( 50x6 mm ) for tublar pole [ galvanized ] ( 1.92 kgs. ) ( cxxviii ) angle / side stay clamp ( 50 x 6 mm ) for tublar pole [ non galvanized ] ( 1.92 kgs. ) ( cxxix ) clamp for g.i. pipe ( 2.02 kgs. ) ( cxxx ) gi flat ( 75x6 mm ) [ galvanized ] ( 1.1 kgs. ) ( cxxxi ) ms flat ( 75x6 mm ) [ non galvanized ] ( 1.1 kgs. ) ( cxxxii ) earth clamp for earthwire ( 50 x 6 mm ) [ galvanized ] ( 1.8 kgs. ) ( cxxxiii ) earth clamp for earthwire ( 50 x 6 mm ) [ non galvanized ] ( 1.8 kgs. ) ( cxxxiv ) ms angle for lt distribution bus ( 50x50x6 mm ) [ galvanized ] ( cxxxv ) ms angle for l t distribution bus ( 50x50x6 mm ) [ non galvanized ] ( cxxxvi ) lt bracket vertical formation ( cxxxvii ) lt bracket for tapping point ( cxxxviii ) lt angle bracket ( 50x50x6 mm ) [ galvanized ] ( cxxxix ) lt angle bracket ( 50x50x6 mm ) [ non galvanized ] ( cxl ) pole clamp for i hook b type ( 0.8 kgs. each ) ( cxli ) lt back clamp ( 50 x 6 mm ) for lt angle [ galvanized ] ( 0.55 kgs. each ) ( cxlii ) lt back clamp ( 50 x 6 mm ) for lt angle [ non galvanized ] ( 0.55 kgs. each ) ( cvliii ) u clamp ( 40 x 6 mm ) [ galvanized ] ( 1.46 kgs. ) ( clxiv ) u clamp ( 40 x 6 mm ) [ non galvanized ] ( 1.46 kgs. ) ( clxv ) 50 x 6 mm galvanized gi flat ( risers ) ( clxvi ) 25 x 3 mm galvanized gi flat ( risers ) fuse ( i ) 11 kv d.o. fuse unit ( polymer type ) ( ii ) 33 kv d.o. fuse unit ( polymer type ) ( iii ) 33 kv h.g. fuse unit ( polymer type ) ( iv ) 11 kv h.g. fuse unit ( polymer type ) electrical conduit ( pipes ) ( i ) gi pipe 4 medium duty ( b class ) ( ii ) gi pipe 6 medium duty ( b class ) ( iii ) gi pipe 8 medium duty ( b class ) ( iv ) hume pipe rcc pipe 100 mm ( np2 class ) ( v ) hume pipe rcc pipe 150 mm ( np2 class ) ( vi ) hume pipe rcc pipe 200 mm ( np3 class ) ( v ) hdpe pipe 110 mm / 4 pe 63 grade ( vi ) hdpe pipe 160 mm / 6 pe 63 grade ( vii ) hdpe pipe 200 mm / 8 pe 63 grade heat shrinkable kit ( i ) 33 kv 3 core xlpe ug cable heat shrinkable straight through jointing kit suitable for 400 mm2 ( ii ) 33 kv 3 core xlpe ug cable heat shrinkable straight through jointing kit suitable for 300 mm2 ( iii ) 33 kv 3 core xlpe ug cable heat shrinkable straight through jointing kit suitable for 240mm2 ( iv ) 33 kv 3 core xlpe ug cable heat shrinkable straight through jointing kit suitable for 185 mm2 ( v ) 33 kv 3 core heat shrikable straight through cable jointing kit for 150 95 mm2 ( vi ) 33 kv 3 core heat shrikable straight through cable jointing kit for 70 35 mm2 ( vii ) 33 kv termination kit for 1core x 400mm2 ( viii ) 33 kv 3 core heat shrinkable out door type cable termination kit for 400mm2 ( ix ) 33 kv 3 core heat shrinkable out door type cable termination kit for 300 mm2 ( x ) 33 kv 3 core heat shrinkable out door type cable termination kit for 240 mm2 ( xi ) 33 kv 3 core heat shrinkable out door type cable termination kit for 185 mm2 ( xii ) 33 kv 3 core heat shrinkable out door type cable termination kit for 120 mm2 ( xiii ) 33 kv 3 core heat shrikable out door cable termination kit for 95 70 mm2 ( xiv ) 33 kv 3 core heat shrikable indoor cable termination kit for 400mm2 ( xv ) 33 kv 3 core heat shrikable indoor cable termination kit for 300 mm2 ( xvi ) 33 kv 3 core heat shrikable indoor cable termination kit for 240 mm2 ( xvii ) 33 kv 3 core heat shrikable indoor cable termination kit for 185 mm2 ( xviii ) 33 kv 3 core heat shrikable indoor cable termination kit for 120 mm2 ( xix ) 33 kv 3 core heat shrikable indoor cable termination kit for 95 70 mm2 ( xx ) 33 kv 3 core heat shrikable indoor cable termination kit for 50 25 mm2 ( xxi ) in door heat shrink type cable termination kit 11kv ht xlpecable 1cx 630 sqmm ( armoured ) ( xxii ) out door heat shrink type cable termination kit 11kv ht xlpecable 1cx 630 sqmm ( armoured ) ( xxiii ) 11 kv 3 core heat shrinkable straight through cable jointing kit 400 mm2 ( xxiv ) 11 kv 3 core heat shrinkable straight through cable jointing kit 300 mm2 ( xxv ) 11 kv 3 core heat shrinkable straight through cable jointing kit 240 mm2 ( xxvi ) 11 kv 3 core heat shrinkable straight through cable jointing kit 185 mm2 ( xxvii ) 11 kv 3 core heat shrinkable straight through cable jointing kit 95 150 mm2 ( xxviii ) 11 kv 3 core heat shrinkable straight through cable jointing kit 70 35 mm2 ( xxix ) 11 kv 3 core heat shrinkable indoor cable jointing / termination kit 400 mm2 ( xxx ) 11 kv 3 core heat shrinkable indoor cable jointing / termination kit 300 mm2 ( xxxi ) 11 kv 3 core heat shrinkable indoor cable jointing / termination kit 240 mm2 ( xxxii ) 11 kv 3 core heat shrinkable indoor cable jointing / termination kit 120 185 mm2 ( xxxiii ) 11 kv 3 core heat shrinkable indoor cable jointing / termination kit 95 50 mm2 ( xxxiv ) 11 kv 3 core heat shrinkable outdoor cable jointing / termination kit 400 mm2 ( xxxv ) 11 kv 3 core heat shrinkable outdoor cable jointing / termination kit 300 mm2 ( xxxvi ) 11 kv 3 core heat shrinkable outdoor cable jointing / termination kit 240 mm2 ( xxxvii ) 11 kv 3 core heat shrinkable outdoor cable jointing / termination kit 120 185 mm2 ( xxxviii ) 11 kv 3 core heat shrinkable outdoor cable jointing / termination kit 95 50 mm2 ug cables related material ( i ) pillar box cum consumer service distribution box one time lock system ( 1 no. 3 ph 4 wire incoming and 5 nos. 3ph 4 wire outgoing ) ( ii ) cable marker ( metal ) ab switch contact ( i ) male female contact of 33 kv ab switch 600 630 amp ( ii ) male female contact of 33 kv ab switch 400 amp ( iii ) male female contact of 33 kv ab switch 200 amp ( iv ) male female contact of 11 kv ab switch 800 amp ( v ) male female contact of 11 kv ab switch 600 amp ( vi ) male female contact of 11 kv ab switch 400 amp ( vii ) male female contact of 11 kv ab switch 200 amp testing equipment ( i ) accuchek meter high accuracy ( 0.2% in director mode / 0.5% in clamp on mode ) for kwh, kvarh and kvah maximum current up to 6a in direct mode and up to 500a in clamp on mode. lt+ : to test lt whole current single phase meters up to 60a ( ii ) accuchek meter high accuracy ( 0.2% in director mode / 0.5% in clamp on mode ) for kwh, kvarh and kvah maximum current up to 6a in direct mode and up to 500a in clamp on mode. lt+ : to test lt 3 phase & ct operated energy meters ( iii ) accuchek meter high accuracy ( 0.2% in director mode / 0.5% in clamp on mode ) for kwh for ht+ : to test meters suitable for ht, 3 phase, 3 wire and 4 wire systems ( iv ) eh ii chain electric hoist ( capacity 1 ton, standard lift 3 mtr ) with 1.5 hp motor ( v ) electronic weighing machine with 1.2x1.2 mtr. platform, suitable for weighing limit upto 2 tons ( vi ) electronic weighing machine with 2x2 mtr. platform, suitable for weighing limit upto 4 tons ( vii ) earth tester 200 amp. 2000 ohm ( digital ) ( viii ) 500 v megger ( ix ) 2.5 / 5 kv megger ( mannual ) ( x ) digital clamp meter ( meco 3150 ) ( xi ) digital tong tester ( 1000 amp., 500 v ) with associated accessories. ( xii ) digital multi meter ( 10 amp along with ma range ) ( xiii ) 2.5 kv motorised with range up to 20000 mega ohms ( xiv ) 2.5 kv motorised cum manual with range up to 20000 mega ohms ( xv ) 5 kv motorised with range up to 100000 mega ohms ( xvi ) 5 kv motorised cum manual with range up to 100000 mega ohms tool kit ( i ) adhesive insulation tape ( ii ) high temperature tape ( iii ) dicharge rod for 33 kv / 11kv ( iv ) screw driver set 840 ( v ) screw driver set 935 ( vi ) neon tester 813 ( vii ) hammer 200 gm ( viii ) hack saw frame ( ix ) hack saw blades ( x ) adjustable spanner ( xi ) wire stripper ( xii ) combinational plier ( xiii ) side cutting plier ( xiv ) measuring tape ( xv ) hand drill machine ( xvi ) punch ( xvii ) knife ( xviii ) spanner set ( xix ) tool bag ( xx ) nose plier ( xxi ) drill bit 3 / 10 concrete ( jk ) ( xxii ) chain pulley 5ton with 15 meter chain ( xxiii ) max pulley 10 ton civil works ( i ) opc cement scada related materials ( a ) scada server ( i ) fep server with interface switches for rtus and frtus ( ii ) isr server { data server } ( iii ) nms server { dms server } ( iv ) dts server ( only at ranchi ) ( v ) developmental server ( vi ) communication server ( vii ) web / directory server ( viii ) workstation with dual tft monitors ( ix ) led based video projection system with 2x3 module configuration with each module at least 67 diagonal with common projector ( x ) 33 kv or 11 kv control and relay panel, scada compatable for feeder protection ( 1f ) ( xi ) 33 kv or 11 kv control and relay panel, scada compatable for transformer protection ( it ) with o / c +e / f + diff relay ( xii ) 33 kv or 11 kv control and relay panel, scada compatable for feeder protection ( 2f ) ( xiii ) buchholz relay contact ( xiv ) minimum oil gauge ( xv ) scada compatible winding temp. indicator ( xvi ) scada compatible oil temp. indicator ( xvii ) rtu base equipment comprising panels, racks, sub racks, powe suppy modules, cpu, analog and digital input control output modules, interfacing mft using rs 485 modbus protocol and 2 ethernet ports + 4 serial ports ( rs232 / 485 ) , required a d converters and all other accessories required ( xviii ) dc voltage transducer ( xix ) rtu base and foundation ( base should be capable of withstanding 200 kg. load ) ( xx ) multi function transducers ( 5 amps, 110 v with rs 485 modbus communication protocol ) ( xxi ) type a frtu for 5 way rmus ( xxii ) type a frtu for 4 way rmus ( xxiii ) type b frtu for 3 way rmus ( xxiv ) type c frtu for 2 way rmus ( xxv ) routers 230 v ac, 2 ge ports, 48xfe, wan speed 200 mbps ( xxvi ) ethernet switch ( xxvii ) 2 mbps vpn link for connectivity for s / s with scada control center ( xxviii ) ldms ( xxix ) 2 kva ups ( for ldms ) with 160 ah battery, 72 v battery set ( xxx ) gsm / gprs modem along with accessories ( xxxi ) b / w laser printer for ldms ( xxxii ) 48 v dc power supply system based on smps for rtu & comm. equipment with 80 ah battery ( xxxiii ) cat 6 cable ( xxxiv ) ldms software ( xxxv ) numerical relay scada compatible for power transformer protection ( xxxvi ) numerical relay scada compatible for 33kv and 11 kv feeder protection ( xxxvii ) mcu module card ( xxxviii ) power module card ( xxxix ) di card ( xl ) do card ( xli ) ai card ( xlii ) com 6 card ( xliii ) rmu 3 way ( 1 incomer, 1 outgoing and 1 breaker ) scada compatible ( xliv ) rmu 5 way ( 1 incomer, 1 outgoing and 3 breakers ) scada compatible ( xlv ) 11 kv sectionalizer ( xlvi ) 11 kv auto reclosure ( xlvii ) gprs / cdma / edge / 3g modem ( xlviii ) heavy duty relay for cb trip / close ( 48 v dc, 2 no, 1 nc ) ( xlix ) 48 v dcps at rtu locations along with vrla batteries ( l ) 11 kv stand alone fault passage indicator complete with gprs enabled modem ( scada compatible ) ( li ) 33 kv stand alone fault passage indicator complete with gprs enabled modem ( scada compatible ) ( b ) storage & backup devices ( i ) external raid mass storage device ( for 2 months online backup ) ( ii ) external dat drive ( c ) switches ( i ) layer ii switch ( scada / dms lan ) ( 48 ports ) ( ii ) layer switch ( planning & development system lan ) ( 24 ports ) ( d ) other active devices ( i ) gps time synchronization system ( ii ) time, day & date digital displays ( e ) printers ( i ) a3 color inkjet printer ( ii ) b / w laser printer ( iii ) color laser printer ( f ) security system ( dmz ) ( i ) web server with load balancing ( ii ) firewall & network ids / ips in pair ( 2 nos. ) ( g ) cabling system ( i ) cable, jacks, hubs, etc. ( ii ) acdb for control centre ( iii ) kvm switch ( iv ) panels ( h ) software for control centre ( i ) scada software ( ii ) isr software ( iii ) dms software ( iv ) dts software ( v ) developmental software ( vi ) network management software ( viii ) gis adaptor / engine for importing data from gis system under it system ( i ) form: f 4: rtu:rtu type b 33 / 11 kv sub stations ( i ) rtu base equipment comprising panels, racks, sub racks, power supply modules, cpu, analog and digital input control output modules, interfacing equipments for interfacing mfts using rs 485 modbus protocol and 2 eathernet ports, required a d converters & all other required items / accessories including complete wiring for all modules for locations mentioned for type b rtus ( ii ) multifunction transducers ( mfts ) ( iii ) contact multiplying relays ( cmrs ) ( iv ) heavy duty relays ( hdrs ) for cb trip / close and rise and lower of oltc ( v ) weather transducer wind speed ( vi ) weather transducer rainfall ( vii ) weather transducer humidity ( viii ) weather transducer temperature ( ix ) weather transducer wind direction ( x ) router for rtus at dc power supply ( xi ) oltc transducers ( xii ) dc current transducer ( xiii ) dc voltage transducer ( xiv ) acdb with sufficient mccbs ( j ) test equipments for rtu ( i ) rtu database configuration & maintenance software tool ( ii ) master station cum rtu simulator & protocol analyzer software tool ( iii ) laptop pc for above software tools along with interfacing hardware including hub ( k ) form: f 5:frtu / frtus ( i ) type a frtu for 5 way rmus ( ii ) type a1 frtu for 4 way rmus ( iii ) type b frtu for 3 way rmus ( iv ) type c frtu for sectionalizers ( v ) mfts ( vi ) contact multiplying relays ( cmrs ) ( vii ) heavy duty relays for cb trip / close ( l ) test equipments for frtu ( i ) frtu database configuration & maintenance software tool ( ii ) master station cum frtu simulator & protocol analyzer software tool ( iii ) laptop pc for above software tools along with interfacing hardware including hub ( m ) f4: gprs / cdma / edge / 3gmodems ( i ) gprs ( n ) form: f 7: auxiliary power supply system ( aps ) ( i ) 20 kva ups ( 1+1 ) with vrla batteries to give 4 hrs back up ( ii ) dc power supply ( dcps ) system based on smps ( for 20 a load plus charging current@10% capacity ) with vrla batteries to give 4 hrs back up. ( iii ) 2 kva ups for rtu locations / ldms ( iv ) 48 v dcps at rtu locations along with vrla batteries ( v ) 24 / 48 v dcps for frtu locations along with vrla batteries safety equipment ( i ) rechargeable led hand torch ( ii ) safety helmet pvc ( iii ) safety shoes ( electrical safety ) ( iv ) rubber hand gloves ( 1.1kv ) commander ( v ) safety double adjustable belts ( karam ) ( vi ) safety items as per the requirement of electrical inspector as under first aid box, shock treatment chart, rubber matts 8 mm thick, 4 fire buckets with sand & m.s. hooks / stand, helmet, hand gloves and, fire extinguisher ( 2 nos ) fire extinguishers ( i ) i kg dry chemical powder ( map 50% ) ; fire rating : 1a, 8b ( ii ) 2 kg dry chemical powder ( map 50% ) ; fire rating: 2a, 8b ( iii ) 4 kg dry chemical powder ( map 50% ) ; fire rating : 2a, 21b ( iv ) 6 kg dry chemical powder ( map 50% ) ; fire rating: 3a, 34b ( v ) 9 kg dry chemical powder ( map 50% ) fire rating: 4a, 55b ( vi ) 6 ltr water type; fire rating : 2a ( vii ) 9 ltr water type, fire rating: 3a ( viii ) 6 ltr mechanical foam type, fire rating: 2a, 21b ( ix ) 9 ltr mechanical foam type, fire rating: 4a, 34b ( x ) 2 kg carbon dioxide type, fire rating: 8b ( xi ) 3 kg carbon dioxide type, fire rating: 13b ( xii ) 4.5 kg carbon dioxide type, fire rating: 21b ( xiii ) 6.5 kg carbon dioxide type, fire rating: 55b ( xiv ) 9 kg carbon dioxide type, fire rating: 70b ( xv ) 22.5 kg carbon dioxide type, fire rating: 70b ( xvi ) gas pressure ctc fire extinguisher ( xvii ) fire buckets ( capacity 10 ltrs. ) feeder pillar / smdb / distribution board ( i ) lt mini feeder pillar ( simple with fuse arrangement ) ( aluminium bus ) ( ii ) smdb ( 1 in, 3 out ) with housing 5 nos 20 amp spn mcb, ( iii ) tpn distribution board 12 way, 50 amp tpn mcb, ( iv ) tpn distribution board 12 way, 100 amp tpn mcb, ( v ) tpn distribution board 12 way, 150 amp tpn mcb, ( vi ) lt feeder piller box for 1 phase 8 connection made of m.s.sheet. ( vii ) lt feeder piller box for 1 phase 12 connection made of m.s.sheet. ( viii ) lt feeder piller box for 3 phase 4 connection made of m.s.sheet. ( ix ) lt feeder piller box for 3 phase 8 connection made of m.s.sheet. ( x ) lt feeder pillar ( simple with fuse arrangement ) ( aluminium bus ) aluminium end terminal lugs 10 sq mm 16 sq mm 25 sq mm 32 sq mm 50 sq mm 70 sq mm 95 sq mm 120 sqmm 150 sq mm 185 sq mm 225 sq mm 240 sq mm 300 sqmm 400 sq mm other misc. equipment ( i ) earthing g.i.strip ( 65x6 ) mm2 ( ii ) rain coat ( iii ) rubber mat along length of pannel ( iv ) aluminium pipe 40 mm dia ( v ) 400 watt / 250 v hpsv lamp fitting complete for 33 / 11 kv pss yard lightining ( vi ) 30 v 80 ah battery charging unit complete with battery and stand ( vii ) 30 volts 100 ah lead acid battery with battery charger and stand ( viii ) 30v, 40 amp. float cum boost battery charger with full wave rectification for 230 v, 1 phase, 50 hz ac input supply as per technical specifications. ( ix ) polycarbonate seal bit ( x ) sticker seal with hologram ( xi ) earth knob ( xii ) ms earth mat for switch yard ( xiii ) rail piece 44.64kg / m 6.92 meter long for power transformer ( xiv ) aluminium binding wire ( xv ) gi wire no. 6 / 8 / 10 ( xvi ) t / c fuse wire 12 / 14 / 16 / 18 / 22 / 28 / 32 swg ( xvii ) m s nuts & bolts of different size ( xviii ) galvanised nuts & bolts ( assorted size ) ( xix ) jointing sleeves ( alumnium ) suitable for 34 / 55 sq.mm ( xx ) jointing sleeves ( alumnium ) suitable for 70 100 sq.mm ( xxi ) jointing sleeves ( alumnium ) suitable for 150 232 sq.mm ( xxii ) anticlimbing device ( barbed wire ) 2x12 swg ( xxiii ) al paint ( xxiv ) red oxide paint ( xxv ) lt phase seperator ( xxvi ) 3 mm thick ms plate with weight of 0.36 kg asset tag ( xxvii ) transformer oil ( ehv grade ) ( xxviii ) natural ester oil ( xxix ) c wedge connector for 0.2sq panther conductor ( nominal aluminum area 200mm2 ) ( xxx ) fault locator machine for ug cables ( flc ) without vehicle ( xxxi ) transformer oil testing kit ( 220 / 230 ac ) ( xxxii ) transformer oil filter machine ( 500 gph ) ( xxxiii ) supply & installation of battery bank of 2 volt 300 ah vrla cells mounted on rack with insulated copper terminal connectors & nut boly ( each set of battery bank consist of 204 nos. vrla cells ) ( b ) furniture ( i ) thrive mid back revolving chair size:75cm ( w ) x 75cm ( d ) x 100cm 109cm ( h ) x 45cm 54cm ( seat height ) . ( ii ) thrive non revolving visitor chair size:63.5cm ( w ) x 59.5cm ( d ) x 97.5cm ( h ) x 42.5cm ( seat height ) . ( iii ) regency non revolving visitor chair with armrest size:59cm ( w ) x 63cm ( d ) x 81.5cm ( h ) x 45cm ( seat height ) . ( iv ) regency mid back revolving chair size:76.3cm ( w ) x 76.3cm ( d ) x 78.5cm 90.5cm ( h ) x 44.2cm 54.2cm ( seat height ) . ( v ) bravo mid back revolving chair size:76.3cm ( w ) x 76.3cm ( d ) x 85.5cm 97.5cm ( h ) x 42.5cm 54.5cm ( seat height ) . ( vi ) high back revolving chair size:76.1cm ( w ) x 76.1cm ( d ) x 114.5cm 131.5cm ( h ) x 44.5cm 54.5cm ( seat height ) . ( vii ) non revolving visitor chair size:60.9cm ( w ) x 64.7cm ( d ) x 98.2cm ( h ) x 46.2cm ( seat height ) . ( viii ) very high back revolving chair size:77cm ( w ) x 77cm ( d ) x 134.9cm 143.9cm ( h ) x 49.9cm 58.9cm ( seat height ) . ( ix ) non revolving visitor chair size:59cm ( w ) x 68.5cm ( d ) x 89.5cm ( h ) x 46.5cm ( seat height ) . ( x ) unlearn single seater cpu / laptop table for computer training hall size: 90cm ( w ) x 60cm ( d ) x 68cm ( h ) ( xi ) unlearn 2 seater laptop table for meeting hall size:135cm ( w ) x 60cm ( d ) x 68cm ( h ) ( xii ) unlearn 4 seater laptop table for meeting hall size:270cm ( w ) x 60cm ( d ) x 68cm ( h ) ( xiii ) talk unitised 4 seater round table size:120cm dia x 75cm ( h ) ( xiv ) talk modular conference table size:67.5cm ( w ) x 60cm ( d ) x 75cm ( h ) ( xv ) enterprise table with cpu hanger size:165cm ( w ) x 90cm ( d ) x 72.8cm ( h ) ( xvi ) insight table for library size:180cm ( w ) x 90cm ( d ) x 74cm ( h ) ( xvii ) versatila v2 table for faculty sitting area size:150cm ( w ) x 89.4cm ( d ) x 75cm ( h ) ( xviii ) executive table with right unit and pedestal size:180cm ( w ) x 210cm ( d ) x 75cm ( h ) ( xix ) main desk table size: 180cm ( w ) x 90cm ( d ) x 75cm ( h ) ( xx ) back unit for impress desk table size: 221.5cm ( w ) x 41cm ( d ) x 200cm ( h ) ( xxi ) display unit tv cabinet walnut color size: 140cm ( w ) x 40cm ( d ) x 75.4cm ( h ) ( xxii ) time out 4 seater pu coated dining table size: 113.5cm ( w ) x 117.5cm ( d ) x 75cm ( h ) ( xxiii ) café chair without armrest size: 52.5cm ( w ) x 55.8cm ( d ) x 84.5cm ( h ) x 45cm ( seat height ) ( xxiv ) apple dining table 6 seater glass top size: 160cm ( w ) x 90cm ( d ) x 75cm ( h ) ( xxv ) silver dining chair size: 44.5cm ( w ) x 41.5cm ( d ) x 96cm ( h ) ( xxvi ) dark walnut dining chair size: 45cm ( w ) x 45cm ( d ) x 95cm ( h ) ( xxvii ) coffee table walnut color size: 100cm ( w ) x 65cm ( d ) x 45cm ( h ) ( xxviii ) 3 seater leatherite sofa size: 205.5cm ( w ) x 92cm ( d ) x 82cm ( h ) ( xxix ) 2 seater leatherite sofa size: 100cm ( w ) x 92cm ( d ) x 82cm ( h ) ( xxx ) single seater leatherite sofa size: 86cm ( w ) x 92cm ( d ) x 82cm ( h ) ( xxxi ) plain almirah size: 91.6cm ( w ) x 48.6cm ( d ) x 198cm ( h ) ( xxxii ) glass door storwel almirah size: 91.6cm ( w ) x 48.6cm ( d ) x 198cm ( h ) ( xxxiii ) single sided wood & steel book rack base unit size:90cm ( w ) x 30cm ( d ) x 189cm ( h ) ( xxxiv ) all steel periodical display rack size:90cm ( w ) x 45cm ( d ) x 183cm ( h ) ( xxxv ) 4 door bookcase ( without top ) size:91.4cmw x 32cm ( d ) x 174.2cm ( h ) ( xxxvi ) white board 4ft. x 3ft. with stand ( xxxvii ) l shaped workstation made of 19mm thk white mdf board with pvc edges.size:1800mm ( l ) + 1200mm ( l ) x 600mm ( d ) x 1200mm ( h ) meter box ( i ) poly carbonate weather proof outdoor type meter cover boxes for single phase meter size 315mm x 265mm x 130mm along with zinc plated clamps ( ii ) poly carbonate weather proof outdoor type meter cover boxes for three phase meters 445mm x 345mm x 170mm along with zinc plated clamps ( iii ) deep drawn m.s. sheet weather proof outdoor type meter cover box for single phase meter size 300mm x 250mm x 160mm along with zinc plated clamps ( iv ) deep drawn m.s. sheet weather proof outdoor type meter cover box for three phase meter size 500mm x 300mm x 160mm along with zinc plated clamps ( v ) metal box of ct 800 / 5 amp ( vi ) meter box made of m / s sheet etc. crca metal sheet each fitted with 4no. racing cost ct ratio 400 / 5a ( vii ) meter box ( viii ) meter box made of m / s sheet etc. crca metal sheet each fitted with 4no. racing cost ct ratio 800 / 5a ( ix ) metal box of ct 400 / 5 amp gas insulated switchgear s / s ( i ) 30kv, 10ka, metal oxide, station class, surge arrester ( scada compliant ) ( for 33kv incoming line, ht side of 2nos. power transformers and 33 / 0.433kv station transformer ) outdoor type with surge counter. ( ii ) 33kv indoor gas insulated switchgear panel ( scada compliants ) with: breaker: 36kv, 1250 a, ( 25ka s.c. rating ) , 3 ph, indoor type breaker ( with 30v dc tripping / closing coil and associated control ) along with marshalling box, terminal connectors and required accessories complete as per applicable ts ct:36kv, 1 ph, 25ka ( 800^00 200 / 1 1 1 a ) indoor type current transformer, having three secondary cores ( protection & metering & current differential protection ) along with terminal connectors, junction box and required accessories etc. complete as per applicable ts ( 1 set = 3 nos. ) pts: 36kv, 1 ph, 33kv / 110 v, single core outdoor type potential transformer along with terminal connectors, junction box and required accessories etc. complete as per applicable ts ( 1 set= 3 nos. ) and digital ammeter / voltmeter / energy meter, o / c and e / f relay etc. the cable chamber shall have 3 nos., 20kv, 10 ka distribution class valve type lightning arresters and isolators of capacity given in ts. for feeder protection ( iii ) 33kv indoor gas insulated switchgear panel ( scada compliants ) consisting of 36 kv breaker 630a, 25 ka for 3 sec, 3 phase single busbar 1250a ( copper ) , 36 kv single phase, ( 800 400 200 / 1 1 a ) 3 nos of indoor type cts, 33 kv / 110volts potential transformers, indoor mounting type control panel, control cabelling between gis and indoor control panel and required accessories, bi metalic clamps, ammeter , voltmeter, modem compatible dlms compliant class 1 meter static tri vector energy meter, relays and accessories complete for bus coupler protection. ( iv ) 33kv indoor gas insulated switchgear panel ( scada compliants ) consisting of 36 kv breaker 630a, 25 ka for 3 sec, 3 phase single busbar 1250a ( copper ) , 36 kv single phase, ( 800 400 200 / 1 1 1a ) 3 nos of indoor type cts, 33 kv / 110volts potential transformers, indoor mounting type control panel, control cabelling between breakers and indoor control panel and required accessories, bi metalic clamps, ammeter , voltmeter, modem compatible dlms compliant class 1 meter static tri vector energy meter, relays and accessories complete for power transformer protection. ( v ) 11 kv indoor gas insulated switch gear panel ( scada compliants ) consisting of 1250 a, 25ka for 3 seconds, 3 ph, indoor type breaker along with 12 kv, 1 phase, 600 300 / 1 1 1 1 amp 3 nos indoor type current transformer, 11 kv / 110 volts potential transformers, indoor mounting type control panel for transformer breaker, control cabling between breaker and indoor control panel and required accessories, bi metallic clamps, a meter, volt meter, modem compatible dlms complaint class a static tri vector energy meter, relay & accessories complete for transformer protection ( vi ) 12 kv, 1250 a, 25ka for 3 seconds, 3 ph, indoor gas insulated switch gear panel ( scada compliants ) along with 12 kv, 1 phase, 600 300 / 1 1 1 1 amp 3 nos indoor type current transformer, 11 kv / 110 volts potential transformers, indoor mounting type control panel for transformer breaker, control cabling between breaker and indoor control panel and required accessories, bi metallic clamps, a meter, volt meter, modem compatible dlms complaint class a static tri vector energy meter, relay & accessories complete for bus coupler protection ( vii ) 12 kv, 1250 a, 25ka for 3 seconds, 3 ph, indoor gas insulated switch gear panel ( scada compliants ) along with 12 kv, 1 phase, 600 300 / 1 1 1 1 amp 3 nos indoor type current transformer, 11 kv / 110 volts potential transformers, indoor mounting type control panel for transformer breaker, control cabling between breaker and indoor control panel and required accessories, bi metallic clamps, a meter, volt meter, modem compatible dlms complaint class a static tri vector energy meter, relay & accessories complete for feeder protection ( viii ) remote terminal unit ( rtu ) & accessories with pc & connections with 30 nos. analog points for voltage, frequency, mw, mvar ; 3 positional analog points for oltc and 28 digital points for breaker and isolator status. ( ix ) flexible cu. earth bond 1cm dia & 500mm long, both end provision of socket suitable for m 16 bolts. ( x ) g 3 gi beam ( 5.05mtr long, consisting of 2 nos 150x75 x5.7mm ) for 33kv incoming line ( 2 nos. beam one for surge arrester and other for isolator, nominal unit wt 0.2 mt ) ( xi ) gi spikes with cone and gi ( 2 nos ) base plate 10mm ( 50x2500 mm gi pipe ) ( unit wt=0.04 mt ) ( xii ) 12 kv, 630 a, 25ka for 3 seconds, 3 ph double break centre rotating type ( dbcr ) , gang operated isolator along with earth switch and support insulators, operating mechanism, base channel, down pipe and all required accessories complete as per technical specifications, without earth switch for substation transformers. ( xiii ) 60 kg / mtr rail pole pieces 5.4 mts ( 2.7x2 ) 44.62 kg per mtr / transformer ( unit wt=0.240 mt ) ( xiv ) 2 tier 2 rows cable trench ( internal width 1500 mm, depth 680 mm, width 75x75x6 mm support angles fixed rcc column of 250 x 250 mm & with ladder type cable tray ( 45x45x5mm two angles at both side having welded flats of 25x5 mm at a gap of 150mm ) for power & control cable ( xv ) chequerred plate 1000x300x5.6mm thick for cable trench in side control room 12 mtr ( xvi ) overhead hoist beam mounted remote opertated for lifting of equipment of control room, capacity 5 tonnes ( xvii ) 36kv, 800 a, 25ka for 3 seconds, 3 ph double break centre rotating type ( dbcr ) , motorised indoor floor mounted off load isolator along with all required accessories complete as per technical specifications, scope of works and approved ( xviii ) external electrification in switch yard area including power receptacles, station yard lighting with 6 nos lighting pole ( fitted with 2x100 watts led flood light ) made of 11 meters high steel tubular poles ( is 2713 part i, ii iii ) of designation 410 – sp 60 and 6 nos light ( 1 x 250 w led ) on structure & control room complete as per technical specifications, approved drawings and scope of the work. ( xix ) internal electrification works of control room comprising of main distribution board, sub distribution boards, copper flexible multi conductor 2.5 sqmm wiring ( for light & fan ) / 4 sqmm wiring ( for power points ) , power and light points, conduits, fan / led lamps / tube fittings, exhaust fans, switches, sockets, 2mm thick, pvc 25mm dia conduits pipes in recess, plugs, miniature circuit breakers, seperate independent earthing ( 2 nos of 40mm gi pipe / 3 m long ) etc as required including dc emergency lighting and auto change over switch as per technical specifcations, approved drawings and scope of work. over head distance to fault locator ( offline ) with signature analyser. a ) accessories & laptop as per latest technical specifications tower line for river crossings ( i ) d type tower for 33kv, 11kv ( double circuit line ) ( 13.56mt each ) with all related nuts and bolts including foundation nuts and bolts ( g i type ) ( ii ) d type tower for 33kv, 11kv ( four circuit line ) ( 15.14mt ) ( double circuit tower +3meter extension each ) with all related nuts and bolts including foundation nuts and bolts ( g i type ) ( iii ) compression type tension hardware fitting for earth wire ( iv ) vibration damper suitable for 7 / 3.15 mm gi earth wire ( v ) 25x500 mm flexible cu. earth bond. covered conductor & accessories ( i ) acsr covered panther conductor ( 200 sq. mm ) ( ii ) acsr covered wolf conductor ( 150 sq. mm ) ( iii ) acsr covered dog conductor ( 100 sq. mm ) ( iv ) mid span joint ( 150 sq mm & 200 sq mm ) ( v ) suspension ties ( ( 150 sq mm & 200 sq mm ) ) ( vi ) tension clamp ( wedge type ) ( ( 150 sq mm & 200 sq mm ) ) ( vii ) insulation piercing connector ( bare to covered ) ( ( 150 sq mm & 200 sq mm ) ) ( viii ) insulation piercing connector ( covered to covered ) ( ( 150 sq mm & 200 sq mm ) ) ( ix ) insulation piercing connector with alumunium bail for earthing ( ( 150 sq mm & 200 sq mm ) ) ( x ) mid span joint ( 100 sq mm & 50 sq mm ) ( xi ) suspension ties ( ( 100 sq mm & 50 sq mm ) ) ( xii ) tension clamp ( wedge type ) ( ( 100 sq mm & 50 sq mm ) ( xiii ) insulation piercing connector ( bare to covered ) ( 100 sq mm & 50 sq mm ) ( xiv ) insulation piercing connector ( covered to covered ) ( 100 sq mm & 50 sq mm ) ( xv ) insulation piercing connector with aluminium bail for earthing ( 100 sq mm & 50 sq mm ) led lights and related items ( i ) led light 190w ( ii ) led light 120w ( iii ) led light 75w ( iv ) led light 40w ( v ) 18 watt led panel bulb with outer 205x205x25 mm sq. and 180x180 mm inner diesel generator sets ( three phase ) with amf panel ( i ) 10kva ( ii ) 20kva ( iii ) 30kva ( iv ) 40kva ( v ) 50kva ( vi ) 62.5kva ( vii ) 82.5kva ( viii ) 100kva ( ix ) 160kva trw related items ( i ) 1 / 2 l.t. brass studs ( ii ) 1 / 2 h.t. brass studs ( iii ) l.t bushing 3347 250 amp ( iv ) l.t. bushing 250 amp ( v ) kraft paper 4 mile ( vi ) insulating paper tap 2.0 mm ( vii ) press board 1 mm ( viii ) bakelite tube 3 / 8x1 / 2 ( ix ) empire sleeving size 4 mm ( x ) r.c. sheet 3 x2x1 / 2 mm ( xi ) inline connector 6 mm ( xii ) cotton tap 1 ( xiii ) r.c. strip ( xiv ) r.c. washer 50x28x2 ( xv ) silicagel breather 200 kva ( xvi ) m.seal ( xvii ) c.i.cap 1 8 1 / 2 ( xviii ) insulating paper top 2.5 mil 20 mm ( xix ) crap paper ( xx ) g.p. thinner ( xxi ) d.a. gray paint ( xxii ) white paint ( xxiii ) nylon washer 3 / 4 ( xxiv ) m.s. plug ( xxv ) l.t. al.strip 6.50x4.50 mm ( xxvi ) dpc aluminum winding wire ( xxvii ) dpc aluminum winding strip ( xxviii ) transformer testing bench panel for 10 kva to 500 kva distribution transformer with its installation & commissioning transformer repairing items ( i ) l.t bushing rod assembly of 750 kva transformer. ( ii ) h.t bushing rod assembly of 750 kva transformer. ( iii ) l.t bushing insulator of 750 kva transformer. ( iv ) h.t bushing insulator of 750 kva transformer. ( v ) l.t bushing gasket set of 750 kva transformer. ( vi ) h.t bushing gasket set of 750 kva transformer. ( vii ) tank gasket set of 750 kva transformer. ( viii ) silica gel breather of 750 kva transformer. ( ix ) arching horn of 750 kva transformer, ( x ) l.t bushing rod assembly of 500 kva transformer ( xi ) h.t bushing rod assembly of 500 kva transformer ( xii ) l.t bushing insulator of 500 kva transformer ( xiii ) h.t bushing insulator of 500 kva transformer ( xiv ) l.t bushing gasket set of 500 kva transformer ( xv ) h.t bushing gasket set of 500 kva transformer ( xvi ) tank gasket set of 500 kva transformer ( xvii ) silica gel breather of 500 kva transformer ( xviii ) arching horn of 500 kva transformer ( xix ) l.t bushing rod assembly of 400 kva transformer ( xx ) h.t bushing rod assembly of 400 kva transformer ( xxi ) l.t bushing insulator of 400 kva transformer ( xxii ) h.t bushing insulator of 400 kva transformer ( xxiii ) l.t bushing gasket set of 400 kva transformer ( xxiv ) h.t bushing gasket set of 400 kva transformer ( xxv ) tank gasket set of 400 kva transformer ( xxvi ) silica gel breather of 400 kva transformer ( xxvii ) arching horn of 400 kva transformer ( xxviii ) l.t bushing rod assembly of 315 kva transformer ( xxix ) h.t bushing rod assembly of 315 kva transformer ( xxx ) l.t bushing insulator of 315 kva transformer ( xxxi ) h.t bushing insulator of 315 kva transformer ( xxxii ) l.t bushing gasket set of 315 kva transformer ( xxxiii ) h.t bushing gasket set of 315 kva transformer ( xxxiv ) tank gasket set of 315 kva transformer ( xxxv ) silica gel breather of 315 kva transformer ( xxxvi ) arching horn of 315 kva transformer ( xxxvii ) l.t bushing rod assembly of 250 kva transformer ( xxxviii ) h.t bushing rod assembly of 250 kva transformer ( xxxix ) l.t bushing insulator of 250 kva transformer ( xl ) h.t bushing insulator of 250 kva transformer ( xli ) l.t bushing gasket set of 250 kva transformer ( xlii ) h.t bushing gasket set of 250 kva transformer ( xliii ) tank gasket set of 250 kva transformer ( xliv ) silica gel breather of 250 kva transformer ( xlv ) arching horn of 250 kva transformer ( xlvi ) l.t bushing rod assembly of 200 kva transformer ( xlvii ) h.t bushing rod assembly of 200 kva transformer ( xlviii ) l.t bushing insulator of 200 kva transformer ( xlix ) h.t bushing insulator of 200 kva transformer ( l ) l.t bushing gasket set of 200 kva transformer ( li ) h.t bushing gasket set of 200 kva transformer ( lii ) tank gasket set of 200 kva transformer ( liii ) silica gel breather of 200 kva transformer ( liv ) arching horn of 200 kva transformer ( lv ) l.t bushing rod assembly of 100 kva transformer ( lvi ) h.t bushing rod assembly of 100 kva transformer ( lvii ) l.t bushing insulator of 100 kva transformer ( lviii ) h.t bushing insulator of 100 kva transformer ( lix ) l.t bushing gasket set of 100 kva transformer ( lx ) h.t bushing gasket set of 100 kva transformer ( lxi ) tank gasket set of 100 kva transformer ( lxii ) silica gel breather of 100 kva transformer ( lxiii ) arching horn of 100 kva transformer ( lxiv ) l.t bushing rod assembly of 63 kva transformer ( lxv ) h.t bushing rod assembly of 63 kva transformer ( lxvi ) l.t bushing insulator of 63 kva transformer ( lxvii ) h.t bushing insulator of 63 kva transformer ( lxviii ) l.t bushing gasket set of 63 kva transformer ( lxix ) h.t bushing gasket set of 63 kva transformer ( lxx ) tank gasket set of 63 kva transformer ( lxxi ) silica gel breather of 63 kva transformer ( lxxii ) arching horn of 63 kva transformer ( lxxiii ) l.t bushing rod assembly of 25 kva transformer ( lxxiv ) h.t bushing rod assembly of 25 kva transformer ( lxxv ) l.t bushing insulator of 25 kva transformer ( lxxvi ) h.t bushing insulator of 25 kva transformer ( lxxvii ) l.t bushing gasket set of 25 kva transformer ( lxxviii ) h.t bushing gasket set of 25 kva transformer ( lxxix ) tank gasket set of 25 kva transformer ( lxxx ) silica gel breather of 25 kva transformer ( lxxxi ) arching horn of 25 kva transformer ab switch repairing item ( i ) jaw of air break switch 600a ( ii ) blade of of air break switch 600a ( iii ) post insulator of air break switch 600a ( iv ) bearing of air break switch 600a ( v ) phase coupling pipe of air break switch 600 a ( vi ) down pipe of air break switch 600 a ( vii ) operating handle of air break switch 600 a ( viii ) operating leaver of air break switch 600 a ( ix ) connector of air break switch 600 a ( x ) arching horn of air break switch 600 a ( xi ) jaw of air break switch 400a ( xii ) blade of of air break switch 400a ( xiii ) post insulator of air break switch 400a ( xiv ) bearing of air break switch 400a ( xv ) phase coupling pipe of air break switch 400 a ( xvi ) down pipe of air break switch 400 a ( xvii ) operating handle of air break switch 400 a ( xviii ) operating leaver of air break switch 400 a ( xix ) connector of air break switch 400 a ( xx ) arching horn of air break switch 400 a ( xxi ) jaw of air break switch 200a ( xxii ) blade of of air break switch 200a ( xxiii ) post insulator of air break switch 200a ( xxiv ) bearing of air break switch 200a ( xxv ) phase coupling pipe of air break switch 200 a ( xxvi ) down pipe of air break switch 200 a ( xxvii ) operating handle of air break switch 200 a ( xxviii ) operating leaver of air break switch 200 a ( xxix ) connector of air break switch 200 a ( xxx ) arching horn of air break switch 200 a vcb repairing item ( i ) trip coil of 33kv vcb ( ii ) trip coil of 11kv vcb ( iii ) closing coil of 33kv vcb ( iv ) closing coil of 11kv vcb ( v ) push button switch 5a ( vi ) test terminal block 5a ( vii ) 33 kv indoor current transformers of ratio as required suitable for metering and protection. ( viii ) 33 kv outdoor current transformers of ratio as required suitable for metering and protection. ( ix ) 11 kv indoor current transformers of ratio as required suitable for metering and protection. ( x ) 11 kv outdoor current transformers of ratio as required suitable for metering and protection. ( xi ) 33000 / 110 volts single phase voltage transformer indoor. ( xii ) 33000 / 110 volts single phase voltage transformer outdoor. ( xiii ) 11000 / 110 volts single phase voltage transformer indoor. ( xiv ) 11000 / 110 volts single phase voltage transformer outdoor. ( xv ) flush type switchboard mounting pattern 96x96 sq.mm m.i. voltmeter ( xvi ) voltmeter phase selector switch. ( xvii ) indicating lamps coloured red, amber and blue, white, green, etc. ( xviii ) auxiliary switch having minimum of 8 contacts, 4 normally open and 4 normally closed ( xix ) flush mounting pattern 96x96 sq.mm m.i. ammeter ( xx ) ammeter selector switch to indicate phase current ( xxi ) over current and earth fault numerical relay ( xxii ) automatic door illuminating lamps with switch ( xxiii ) 240 v, 100 w, ac single phase anti / condensation heaters, with thermostat ( 0 60 deg. c ) and switch. ( xxiv ) operation counter for vcb ( xxv ) bus bar spout epoxy casted r phase of 33kv indoor vcb ( xxvi ) bus bar spout epoxy casted y phase of 33kv indoor vcb ( xxvii ) bus bar spout epoxy casted b phase of 33kv indoor vcb ( xxviii ) circuit spout epoxy casted of 33kv indoor vcb ( xxix ) housing for vacuum interrupter of 33kv indoor vcb ( xxx ) drive insulator 33kv vcb ( xxxi ) release coil of 33kv indoor vcb ( xxxii ) bus bar spout epoxy casted r phase of 11kv indoor vcb ( xxxiii ) bus bar spout epoxy casted y phase of 11kv indoor vcb ( xxxiv ) bus bar spout epoxy casted b phase of 11kv indoor vcb ( xxxv ) circuit spout epoxy casted of 11kv indoor vcb ( xxxvi ) housing for vacuum interrupter of 11kv indoor vcb ( xxxvii ) drive insulator of 11kv vcb ( xxxviii ) release coil of 11kv indoor vcb ( xxxix ) vacuum interrupter of 33kv outdoor type ( xl ) vacuum interrupter of 33kv indoor type ( xli ) vacuum interrupter of 11kv outdoor type ( xlii ) vacuum interrupter of 11kv indoor type ( xliii ) buzzer / hooter ( xliv ) t n c switch mrt related items ( i ) fully automatic energy meter test bench with 0.02 class, 10 position, for testing of 1 ph & 3 ph energy meters with 5 years maintenance, accreditation from nabl and software updation. ( ii ) instrument transformer ( ct pt ) test system ( iii ) transformer turn ratio meter and measurement test kit ( iv ) transformer oil filtering machine 500 gph ( v ) circuit breaker operational analyzer ( vi ) 3 ph relay test kit with all necessary accessories ( vii ) primary injection kit 1000 a with relay testing facility ( viii ) ht coil winding machine its installation, testing & commissioning ( ix ) lt coil winding machine its installation, testing & commissioning ( x ) 03 ( three ) phase transformer winding resistance meter ( xi ) digital multimeter, 750v ( xii ) capacitance tan delta test set for transformer, motor and switchgear ( xiii ) capacitance tan delta test set for cables ( xiv ) vaccum interrupter tester ( xv ) secondary injection kit ( xvi ) digital ht earth tester ( xvii ) 3 ph power quality analyser ( xviii ) 05 kv insulation tester ( manual ) ( xix ) 10 kv insulation tester ( motarized ) ( xx ) digital clamp meter; 20 1000a, 200 v dc ( xxi ) digital clamp meter; 20a ( 1ma 20a ) ( xxii ) discharge rod ( make fibre ) ( xxiii ) thermal imaging camera ( xxiv ) single phase & three phase meter automatic testing bench for 20 positions ( 0.02s class rsm ) frp fencing ( i ) fiber reinforced plastic ( frp ) fencing for 11 / 0.433kv, 63 / 100 / 200 / 500 kva substation etc...

Drinking Water And Sanitation Department - Jharkhand

31897243 e quotation for seeking firm rates for non schedule items for preparing estimates. gr c repairing of electro mechanical assets and all their associate works like repairing of motors, pumps, starters, panel, cables etc. at rinpas, kanke, ranchi , c / f pump sets , cost towards dismantling of 100 hp wpil make single stage c / f pump and taking out its rotating unit assembly with changing of damaged parts by new making s / f neck ring as per sample size 2 nos, c.i shaft sleeve as per sample size – 2nos, making s / f shaft sleeve check nut as per sample size – 2 nos , s / fball bearing skf 6309 2 nos and repairing of bearinghousing by welding turning machining as per bearing size 2 nos, c.i gland tightner as per sample size – 2nos including cost of reassembling of rotating unit assembly balancing rotating unit assembly and fitting the pump with supply of grease gland packing oil packing paper with transporting cost of rotating unit from p / plant to workshop and back , cost toward supplying fitting & changing of 100 hp jyoti make motor ball bearing skf 6316 at de side 1 no. and sk 6314 nde 1 no. with grease. , cost towards repairing of 100 hp l & t make f.a.s.d starter with s / f contactor set 2 sets ) , relay unit ( 85 135a ) 1set, timer unit 1 set, making new connection etc all complete. , supplying and fitting 6”dia tyre coupling complete set with nut bolt washer and tyre of reputed make for 100 hp pump set. , cost towards supplying and fitting mccb 630 amp. for bus bar make l&t schneider / bch , cost towards supplying and fitting mccb 250 amp. for bus bar make l&t schneider / bch , cost toward supplying fitting & changing 100mm dia cidf sluice valve ( pn 1 ) 1 set & cidf nr valve ( pn 1 ) 1 no. including fitting charge , cost toward supplying fitting & changing 150 mm dia ci foot valve hiding single leather flat and gun metal seating all complete. , cost towards providing all labours tools & techniciansfor dismantling and disconnecting of 40 hp kirloskar make motor and taken out rotor from motor stator cutting removing burnt and damaged coil and after repairing refitting the same etc all complete. , cost towards full rewinding of 40 hp motor stator with supplying of super enameled round copper conductor suitable gauge class f insulating materials making all connection taping, varnishing with dr beck varnish all complete with deducting the cost of taken out scrap materials ( wt. of wire is 18.5kg approx ) . , s / f ball bearing skf make 6312&6309 at de&nde side of 40 hp kirloskar make motor including proper greasing all complete. , cost towards providing all labour tools and tackles for dismantling of 40 hp single stage kirloskar make c / f pump with changing damaged parts such as gm neck ring as per size and sample 2 nos. shaft sleeve 2 nos. shaft sleeve check nut 2 nos. making ci bearing housing as per size and sample 2 nos. supplying and fitting ball wearing skf make 6309 2nos. making supplying and fitting ms gland tightner as per size and sample 2 pair making citric motion of rotating unit assembling on lathe m / c etc all complete , cost towards repairing of 40 hp l&t motor starter by supplying and fitting l&t make 3 core ml 4 power contactor 45 amp. with auxiliary contractor complete set 2nos. supplying and fitting timer type lt 100 1nos., over load relay suitable range 1nos.etc all complete. , cost towards providing all labours tools & technicians for taking out damaged 250amp. tpn hrc fuse type disconnector main switch replacing new disconnector fuse unit with hrc fuse 1 set doing electrical connection and testing on full load after deducting the cost of taken out scrap materials , supplying and fitting 6”dia tyre coupling complete set with nut bolt washer and tyre of reputed make for 40 hp pump set. , cost towards providing all labour tools and tackles for dismantling and taken out damaged nr valve and s / f 4”dia c.i df nr valve heavy duty rating pn 1 isi marked on delivery pipe line with all work including cost of labour charge all complete testing on full load with deducting the cost of scrap materials. , cost towards supplying and laying 50 mm² x 3.5 core aluminium armoured cable from main switch to industrial panel. ( both sets ) . , cost towards supplying and laying 16 mm² x 3 core copper cable from panel to starter and starter to motor in bunch of two. ( both sets ) . , cost towards replacing damaged suction pipe by making supply & fitting 100 mm dia heavy duty m.s. suction pipe 10feet long both and 100 mm dia m.s. flange welding, 100mm dia long bend 1 no with nut bolt rubber insertion etc required for the job. , transportation charge of above p / set from work site to work shop and vice versa including loading and unloading charge. , submersible pump sets , cost towards providing all labour tools and technicians for dismantling and taken out 5hp submersible p / set with column pipe for bore well. , cost towards for rewinding and repairing of5 hp submersible motor with s / f 1.2 swg round copper winding wire 24 slot, gun metal bush, thrust plate, thrust bearing, diapharm, oil seal, etc with lathe work. all complete. after the deduction of cost of scrape materials. , cost towards repairing of5 hp submersible pump with s / f norylimpeller as per size and sample, diffuser, s.s. shaft, s.s. coupling, s.s. sleeve, nut, c.i. suction casing, c.i nrv etc. all complete ( 23 stage ) after the deduction of cost of scrape materials. , cost towards s / f and changing of 2”dia upvc column pipe with heavy duty socket ( make supreme / paras ) for both sets. , cost towards replacement of damaged submersible cable by supplying and fitting 4 mm2x 3 core flat submersible cable including cable jointing all complete. after the deduction of cost of scrape materials. dwsd m1062 , providing all labour, tools tackles& technicians for lowering of 5hp submersible pump set with all accessories in the bore well , cost towards supplying and fitting ( 1 ) 50 mm dia g.m. full way valve – 1 no ( 2 ) 40 mm dia nr valve – 1 no ( 3 ) 40 mm dia g.i. bend ( 4 ) 2” dia m.s. clamp with nut bolt 2 pair after the deduction of cost of scrape materials. , supplying and installation suitable size panel board for 5 hp submersible pump including fixing on wall comprising of following points such as ( 1 ) d.o.l starter 1no. ( 2 ) hrc fuse – 3 no. ( 3 ) voltmeter with selector switch – 1 set ( 4 ) ammeter with selector switch – 1 set ( 5 ) phase indicating neon lamp – 3 nos. etc. all complete after the deduction of cost of scrap materials. , supplying all material such as 40 mm dia g.i. pipe medium quality 15 ft. long, charcoal salt etc. for making earthing station as per i.e. rule , supplying and laying ground and on wall 10 swg, g.i. wire for doing continuous earthing for all electrical equipments , cost towards replacement of old and damaged underground service line by supplying new overhead line 10 mm² 3core copper wire after the deduction of cost of scrap materials. , supplying and laying ( under and over ground ) 2 dia aqua gold weather proof pvc pipe from bore well to main rising pipe line ( damaged pipe replacement ) make supreme / isi mark ( both sets ) , supplying and laying 1.5 dia under and over ground supreme aqua gold / any reputed make weather proof upvc pipe from bore well to dharamshala over head tank. , supplying and fitting union 1.5 dia , supplying and fitting elbow 1.5 dia , supplying and fittingtee 1.5 dia , supplying and fitting socket 1.5 dia , supplying and fitting upvc valve 1.5 dia , transportation charge of above p / set from work site to work shop and vice versa including loading and unloading charge....

South Eastern Railways - Jharkhand

31789061 supply of 2 hp submersible pump, single phase with dol er ith voltmeter, ammeter2 hp submersible pump, single phase with dol er ith voltmeter, ammeter,2 hp submersible pump, single phase with dol starter ith voltmeter, ammeter, overload relay, head 214 247 mtr. discharge: 0.5 0.9 m3/hrs, discharge pipe dia 32 mm, make: kirloskar, cri,ksb or similar....

South Eastern Railways - Jharkhand

31788389 supply of 15 hp open well submersible pump monoblock rating 15 hp with er.15 hp open well submersible pump monoblock rating 15 hp with er.,15 hp open well submersible pump monoblock rating 15 hp, head 25 to 30 mtrs,discharge 30 50 lps, rpm:2900, stage 1, phase 3(three), voltage 380+/ 23%, 50 hz with suitable starer for 15 hp openwell submersible pump with protection relay, ammeter, voltmeter, selector switch, indicators, make kirloskar, ksb, cri or similar...

South Eastern Railways - Jharkhand

31578354 supply of 15 hp open well submersible pump monoblock rating 15 hp15 hp open well submersible pump monoblock rating 15 hp,15 hp open well submersible pump monoblock rating 15 hp, head 25 to 30 mtrs,discharge 30 50 lps, rpm:2900, stage 1, phase 3(three), voltage 380+/ 23%, 50 hz with suitable starer for 15 hp openwell submersible pump with protection relay, ammeter, voltmeter, selector switch, indicators, make kirloskar, ksb, cri or similar...

Central Coalfields Limited - Jharkhand

31577202 bids are invited for insulators complete set for unitized s,station , vacuum bottle 800 amp 20ka , breaker charging handle , trip coil , push button with contact block , limit switch , spring charging motor 110v ac,dc , auxiliary switch,6 no,plus 6 nc , ammeter, selector switch , ammeter , voltmeter , closing coil , auxiliary contactor with2 no,plus 2 nc ,voltmeter, selector, switch , support insulator for isolator ,master trip relay , copper busbars incoming for unitizeds,station , epoxy,resign,moulded cbct id 110 , h.d resincast current transformer 400,200,5,5a , heavy duty epoxyresin cast potential transformer ratio 11kv,110v total quantity : 64...

Central Coalfields Limited - Jharkhand

31506889 repair of acb and starter 2 supply & fixing of copper terminal bushing with stud, nut, washer complete for incoming / outgoing / through going & isolator chamber to control circuit chamber. 3 supply & fixing of copper lug / socket 120 sq mm for connecting of copper cable 300 amp grade. 4 supply & fixing of 12 way / 30 amps. close connector std. make. 5 supply & fixing of copper strip 25mm x 12mm for isolator bus bar. 6 supply & fixing of male & female bushing with brass stud nut with washer 550v grade. 7 supply & fixing of ferules, lugs, clips, socket, wiring bolts etc. for circuit wiring. 8 supply & fixing of 2.5 sqmm ( 1.1 kv grade ) flexible copper wire std. quality. 9 supply & fixing of led indicator lamp set with resistance fitted complete set. 10 supply & fixing of cbct for earth leakage relay 750ma. 11 supply & fixing of electronic type sensitive e / l relay 750 ma with time delay second. 12 supply & fixing of hrc fuse with carrier 30 amps. 13 supply & fixing relay & base with 11 pin, 12 volt. 14 supply & fixing of l.t., c.t. for metering. 15 supply & fixing of lead incoming round copper stud type for 300 amps. 16 supply & fixing of fixed contact carrier assembly for 300 amps. 17 supply & fixing of moving contact carrier assembly for 300 amps. 18 supply & fixing of mechanism latch lever set. 19 supply & fixing of shunt relay. 20 part b ( enter zero for this row ) 21 supply & fixing of 200 / 5 ammeter 22 supply & fixing of 600 v voltmeter 23 supply & fixing of hr fuse with carrier 30 amp 24 supply & fixing of electronic type sensitive e / l relay 750ma with time delay second 25 supply & fixing of cbct for earth leakage relay 750 ma 26 supply & fixing of pneumatic time delay relay range 3 to 60 second. 27 supply & fixing of lt ct for overload protection. 28 supply & fixing of lt ct element 1no + 1nc push switch. 29 supply &fixing of copper terminal bushing with stud, nut, washer completed for incoming / outgoing / through going & isolator chamber to control circuit chamber. 30 supply & fixing of copper lug / socket 120 sq mm for connecting of copper cable 300a grade. 31 supply & fixing of led indicator lamp set with resistance fitting complete set for 3nos of phase & 1no. of e / l relay 32 supply & fixing of single phase preventor 550v 33 supply & fixing of tc contactor 550v. 34 supply & fixing of p.t 550v / 220v / 110v / 24v / 12v. 35 supply & fixing of 12way / 30amp close connector standard make. 36 supply &fixing of copper strip 25mm x 12mm for isolator busbar. 37 total impact of gst for the purpose of ctc...

Central Coalfields Limited - Jharkhand

31383444 bids are invited for insulators complete set for unitized s,station , vacuum bottle 800 amp 20ka , breaker charging handle , trip coil , push button with contact block , limit switch , spring charging motor 110v ac,dc , auxiliary switch,6 no,plus 6 nc , ammeter, selector switch , ammeter , voltmeter , closing coil , auxiliary contactor with2 no,plus 2 nc ,voltmeter, selector, switch , support insulator for isolator ,master trip relay , copper busbars incoming for unitizeds,station , epoxy,resign,moulded cbct id 110 , h.d resincast current transformer 400,200,5,5a , heavy duty epoxyresin cast potential transformer ratio 11kv,110v total quantity : 64...

Drinking Water And Sanitation Department - Jharkhand

31336207 karimati and adjoining village rural pipe water supply scheme under drinking water and sanitation division hazaribag karimati and adjoining village rural pipe water supply scheme under drinking water and sanitation division hazaribag , esrcapacity with staging 24 m 400 kl. , doing geotechnical survey, collecting field data, designing aesthetically, getting it approved by competent authority and providing all labours andequipment for designing & construction ofesr all complete job. , designing ( aesthetically ) , and constructing rcc elevated service reservoirs of following capacity with rcc staging consisting of columns, internal and external bracings spaced vertically not more than 4.5 metres centre to centre for esr having capacity upto 500 cum and not more than 6m c / c for esr shaving capacity above 500 cum including excavation in all types of strata, foundation concrete, cement plaster with water proofing compound to the in side and outside face of the container and also plaster with plastic paint in all columns and bracingsincluding refilling disposing off the surplus stuff with in a lead of 50 metres, all labour and material charges including lowering, laying, erecting, hoisting and jointing of pipe assembly of inlet, outlet, washout, overflow and bypass arrangements as per departmental design, providing and fixing accessories such as m.s. ladder, outside, stainless steel ladder in contenor, c.i. manhole frame and covers, water level indicators, l ightening conductor, g.i. pipe railing around walk way and top slab, providing stair case from ground level to roof level , ms grill gate of 2m height with locking arrangement of approved design, b.b. masonary chambers for all valves ventilations shafts, providing and applying three coats acrylie emulsion with silicon edditives paint to the structure including roof slab, epoxy painting to internal surface and anti termite treatment for underground part soft the structure and giving satisfactory water tightness test as per is code. the job to include painting then ame of the scheme and other details on the reservoir as per the directions of engineer in chief. , providing spiral stair case from ground level to roof level, m.s. grill gate of 2m height with locking arrangement of approved design, b.b. masonry chambers for all valves, providing and applying three coats of cement paint to the structure including roof slab, epoxy painting to internal surface and anti termite treatment forunder ground part soft he structure and giving satisfactory water tightness test as per i.s. code. the job to include painting then ameof the scheme and other details on there servoir as per the directions of engineer in charge. , notes , the design of the structure be in accordance with relevant i.s. specification ( i.s. 3370 2009 or revised. ) , the design shall satisfy the stipulations as per i.s. 1893 1984 and i.s.13920 / 1993 for seismic force and i.s. 11682 / 1985 for r.c.c. staging of over head tanks. , for design having more than 6 columns, provision of internal bracing is obligatory. external bracings is also obligatory. , the entire structure shal be m / 250 mix only .however concrete in contract with water such as container base slab, walls, roofs slab & putting in water base area shall be in m300 , plain round mild steel bars grade i conforming to i.s.432 part i orhigh yield strength deformed bars conforming to i.s. 1786 or i.s. 1139 shall beused, grade i imildsteel bars will not be allowed , irrespective of the type of foundation proposed in the design, one set of bracing be provided at the ground level. , these rates include providing m.s. ladder for e.s.r.s upto 2 lakh litres capacity and providing spiral stair case for e.s.r. above 2 lakh litres capacity. , staging shall have to bede signed with stresses of m 200 concrete for esr. however all rcc construction should be donein m 250. structures in contact with water shall be designed & casted in m 300 , these rates are including the cost of up lift pressure if any and entire dewatering during execution. incase of water logging are a where water is struck at shallow depth, extra provision of dewatering shall be made as per site condition. , all conditions given in the member secretarys circular no. mjp / ts i / 350 / 1668 dt. 2 8 97 and mjp / s i / 350 / 2127 dt. 13 7 99 shall be strictly followed and additional cost, if any, due to these conditions is included in the rates mentioned below. , 75 % part rate shall be payable for reinforcement concrete and plastering items of containers of e.s.r. till satisfactory hydraulic testing for water tightness is given; and till that work shall be treated as incomplete. , the rates indicated in the table are excluding the cost of pipes, specials and valves required for inlet, outlet, washout, overflow and bypass arrangement. the scope of work, however, includes cost of erecting, laying and jointing of pipe sand valves including cost of jointing materials upto 5 m beyond outer face of outer most column. , for esr upto 500 cum capacity c.i. double flanged pipes upto 300 mm dia shall be provided and c.i. specials shall be used. for esr above 500 cum capacity c.i. / m.s. pipe assembly with minimum 8 mm thickness upto 500 mm dia and minimum 10 mm thickness above 500 mm dia can be used with proper anti corrosive epoxy treatment from in side and out side. , below mentioned rates are for foundation swith individual footing with bearing capacity of 20 tonnes per square metre. for raft foundations, these rates shall be increased by 7.5% where safe bearing capacity ( sbc ) is 5 mt per sqm and by 5 % where sbc is more than 5mt / sqm and upto 10 mt / sqm. this % of5 % or 7. 5 % is applicable for estimation of amount of lumpsum item of esr. for extra item due to change from individual foundation to raft, actual increase in concrete and steel be paid as per relevant dsr item. , the rate shall be increased by 30 % for bearing piles upto depth of 10 m and for further increased in depth by 5 m each, it shall be increased by another 10%. these rates are applicable where raft is not feasible. for pile foundations sulphate resistant cement shall only beused. single pile for the column is not permitted, group of piles shall be designed with pile cap for each column of esr. , esr ( capcity 400 kl ) with staging 24m , , construction of 1.5 mld wtp , doing geotechnical survey, collecting field data, designing aesthetically, getting it approved by competent authority and providing all labours and necessary equipment for designing & construction ofunconventional wtp .with all complete job. , designing ( aesthetically ) , providingconstructinghigh rate unconventionalwatertreatmentplant i.e. simplified water treatment plant consisting of civilworks includingcostofprovidingandapplyingepoxypainttoinsidesurfaceofwaterretainingstructuresincontactwithchlorineandprovidinganti termitetreatmenttoentirestructurebelowgroundlevel, ceramic tiles for floring, acrylic emulsion with silicon additives paint from outside stainless steel railing, mechanicalandelectricalcomponentsofvarioussub worksasgivenbelow, includingnecessaryhydraulic testing, structuraltesting, andtrial fora periodof3 months, etc. completeas directedbyengineer in charge ( turn key job ) works. , aeration fountain , inlet arrangements , mixing channel with ventury flume and flow measuring arrangement , inlet channel , flocculator conforming to i.s. 7208 1974 ( type c ) with detention period of 30 minutes , tube settlers designing, fabricating and constructing tube settlers with square or any other shaped tube like circular, cheveron, hexagonal etc .having proven performance , rapid sand gravity filters , filter house , chemical house , alum tanks 2nos. with mixing, carrying and dosing arrangements with piping. , gravity feed gas chlorinator with 100% standby. , tcl solution tank with mixing, carrying and dosing arrangement with piping. , bypass arrangement , external and internal electrification , laboratory equipments , wash water tanks of capacity equal to 12 minutes to wash specified numbers of filter beds at time at 600 liters / m2 / m under head of 12 m at under drain. , wash water pumps with 100% standby , air blowers capable of delivering 600 lmp per square metre of free air of filter area at 0.4 kg / sqcm at the under drains ( 100 % standby ) . air blowers shall be adopted for wtp having capacity more than 3 mld only . below 3 mld capacity, air blower shall not be adopted. , pure water sump of capacity equal to 1 hourpumping capacity. , pure water pump house over the sump / by the side of sump. , drainage arrangements , alum store , sanitary block with necessary water supply and drainage arrangements and internalwbm roads. , these rates are applicable for seismic zones 2, 3 and 4. , rates given below are inclusive of uplift pressure if any and dewatering during the entire work. , all rcc structures shall be constructed in m 250. structures in contact with water shall be in m 300. , unconventional treatment plants less than 1 mld capacity shall not be constructed. , 1.5 mld un conventional wtp capacity , construction of r.cc intake well cum pump house with dia of well 5.00 m, steining wall 8.65 m, and hieght of pump house 5m. , doing geotechnical survey, collecting field data, designing aesthetically, getting it approved by competent authority and construction of r.c.c intake well with pump house all complete job. , earth work in excavation offoundationtrenches of toe wall , spillway, head regulator, outlet, intake well etc as per designed section in all kindsof soil including , moorum soil, mixed with kankar, pebbles and bouldersupto 300 mm sizeand disposalof thesame ( beyond50m awayfrom the edge of the trenches ) initial lift of 1.5 mtr as per specification and direction of e / i. , initial lift , 1st lift , earth work in excavation offoundationtrenches of toe wall , spillway, head regulator, intake well and outlet etc as per designed section in ordinary rock or soft rock ( where blasting is not needed ) ( vide classification of soil item c ) with disposal of soil ( beyond50m away from the edge of the trenches ) withinitial lift of 1.50 mtr as per specification and direction of e / i. ( soft rock where blasting is not required and approved by the concerned chief engineer. ) , 1st lift , 2nd lift , 3rd lift , providing and laying p.c.cm 150 with nominal mix ( 1:2:4 ) in foundation with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of f.m 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specificationanddirection ofengineer incharge. , foundation , providing and laying in situ cement concrete of trap / granite / quartzite / gneiss metal for rcc work in foundation like raft, grillage, strip foundation and footing of rcc columns and steel sanchions including normal dewatering, plywood form work, bully / steel propups, compaction, finishing and curing, etc, complete. ( by weigh batching and mix design for m 250 and m 300 only. ( excluding m.s or tor reinforcement ) . , r.c.c m 300 in foundation , providing and casting in situ cementconcrete of trap / granite / quartzite / gness metal of approved quilty for r.c.c work as per detailed drawing and designs or as directed by engineer in charge including narmol dewatering, sentering plywood, formwork bully / steel prop ups, compaction finishing the formed surface with 1:3 sufficeint minimoum thickness if special finish is to be provided and curing etc. complete. ( excluding the cost of reinforcement.for rcc m 300 grade slabes / landings / vertical walls / waist slabs / steps for staircase in foundation stain wall of intake well. , providing and casting in situ cement concrete of trap / granite / quartzite / gneiss metal of approved quilty for r.c.c work as per detailed drawing and designs or as directed by engineer in charge including narmol dewatering, centeringplywood, formwork bully / steel prop ups, compaction finishing the formed surface with 1:3 sufficeint minimum thickness if special finish is to be provided and curing etc. complete ( by weighbacthing and mix design for m 250 only .excluding the cost of reinforcement. , rccm 250 floor slab beam , rccm 250 pump house roofslab beam , providingand costing in situ cementconcrete of trap / granite / quartzite / gness metal of approved quilty for r.c.c work as per detailed drawing and designs or as directed by engineer in charge including narmol dewatering, sentering plywood, formwork bully / steel prop ups, compaction finishing the formed surface with 1:3 sufficeint minimoum thickness if special finish is to be provided and curing etc. complete ( by weighbacthing and mix design for m 250 & 300 only . ( excluding the cost of reinforcement. , for rcc slabs / landings / vertical walls / waist slabs / steps / staircase for floor slab. , providing r.c.c m 250 in nominal mixin columns with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of f.m 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing ( but excluding the cost of reinforcement ) taxes and royalty all complete as per building specificationanddirection ofengineer incharge. , columns up to roof level , providing r.c.c m 250 in nominal mix in lintel with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of f.m 2.5 to 3.0 excluding screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing ( but excluding the cost of reinforcement ) taxes and royalty all complete as per building specificationanddirection ofengineer incharge. , band at lintel level , providing r.c.c m 250 in nominal mix in roof slab of all types with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of f.m 2.5 to 3.0 excluding screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing ( but excluding the cost of reinforcement ) taxes and royalty all complete as per building specificationanddirection ofengineer incharge. , pump house roof , providing 63 mm average thick rcc m 250 with nominal mix ofin chhajja with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of fm 2.5 to 3 including, taking drip course in concrete screening, centering, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, 6 mm thick cement plaster ( 1:4 ) in ceiling and sides of chhajja with sand offm 1.5, curing ( but excluding the cost of reinforcement ) taxes and royalty all complete asper building specification and direction of e / i. , providing tor steel reinforcement of8mm to 12 mm dia.rodsas per approved design drawing excluding carriage of m.s rods ( straight or in coils ) to work site, cutting, bending, binding including supplying an nealed wire placing ms rods in position all complete job as per specification and direction of e / i. , providing designation 75a brick work in c.m. ( 1:6 ) in superstructure with approved quality of clean coarse sand of f. m. 2 to 2.5 including providing 10 mm thick mortar joints, costs of screening, materials, scaffolding, ranking out joints to 15mm depth curing, taxes & royalty all complete as per building specification & direction of e / i. , providing 25 mm thick . first class patent stone flooring ( 1:2:4 ) with stone chips in two layers , bottom layer 19 mmthick ( 1:2:4 ) with 12 mm to 6 mm size graded stone chips and top layer 6 mm thick ( 1:3 ) with 6 mm down stone chips in pannels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes & royalty with all complete as per building specification & direction of e / i. , supplying fitting and fixing fully glazed steel door window or ventilators of standard rolled z and mullion section and sizes as per i.s. 1038 joints met and welded with 100x16x3 mm ms lugs fixed in cement concrete ( 1:2:4 ) blocks 15x10x10 cm size including cost of oxidized iron fitting with hinges, handle per teps, catch springs 3mm thick plain glass panes with aluminium beads and inner frame fixed with lugs of 20 mm long 6.3mm g.i.counter sunk machine screw and nuts and applying a coat of red lead paint, carriage to work site hoisting and placing in position in all storey and taxes all complete as per building specification and direction of e / i , supplying fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20x10x2 mm at 100 mm.centers and braced with m.s. flat diagonals 20x3mm with top & bottom rails of t iron 40x40x6 mm with 38 mm dia steel pulleys complete with bolts, nuts locking arrangement stoppers handles including applying a priming coat of red lead paint, carriage hoisting and taxes all complete as per building specification and direction of e / i. , providing 12 mm thick cement plaster ( 1:6 ) with approved quality ofcleancoarse sandoffm1.5 with 5% cico or any other water proofing compound including screening, curing with all leads andliftsofwaterscaffolding taxes and royaltyall complete as per building specification and direction of e / i. , providing 12 mm thick water proof cement plaster ( 1:3 ) with clean coarse sand of fm 1.5 with 5%cico or any otherwater proofing compound including screening curing, with all leads and lifts of water, scaffolding taxes and royalty all complete as per buildingspecification and direction of e / i. , providing 6 mm thick cement plaster ( 1:4 ) in ceiling with approved quality ofclean coarse sand of fm 1.5 including screening, curing with all leads and lift of water , scaffolding taxes and royalty all complete as per building specification and direction of e / i. , providing 2 coats of snowcem of approved shade and make over a coat of cement primer on new surfaceincluding preparing the plastered surface smooth with sand paper, curing, scaffolding & taxes all complete as per building specification & direction of e / i , providing one coats of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of e / i. , providingr.s.joist ismb350 x 140 mm ) size fitting fixing in position including cutting to reacquired in shape & size, its carriage applying a primer coat of red lead paint etc all complete as per building specification and direction of e / i. ( below roof slab for base of v.t.pump ) ( as per ( c ) ( iii ) 5.50 m @ 52.40 kg per meter ) 0.34 mt, , providing and fixing gi pipe railing having 1.0m height consisting 50 x 50 x 6 mm thick m.s angles as vertical at 1.5 m c / c, and additional posts at every corner 3 rows of 25 mm dia g.i pipes fo medium class variety as horizontal and painting 3 coats of oil paint over 1 coats of anticorrosive paint of approved colour and shade including cost all labour, transporting bends to curved shape, etc complete. , providing double flanged sluice gate confirming for is 2906 / 14846 including worn gear arrangement as per test pressure stainless steel spindle, caps including all transportation etc.complete. , providing and fixing in position c.i. / m.s. rose pieces in intake well including cost of all materials and labour, painting with three coats of anti corrosive all paints, etc complete as directed by engineer in charge , supplying materials and labour for fixing 20mm dia m.s bar steps in steining wall of 0.30 m internal and staggered in ( 1:2:4 ) cement concrete including scaffolding and curing etc.all complete as per specification and direction of e / i. , carriage of construction materials to work site including loading, unloading & stacking etc. all complete. , cement10km lead , steel10km lead , sand36km lead , bricks6km lead , stone / stone chips11km lead , construction of gang way 50 m long and 3.00 m wide , doing geotechnical survey, collecting field data, designing, getting it approved by competent authority construction of gang way 40 m long and 3.0 m wide etc. all complete job. , e / w in excavation in foundation trenches in foundation trenches in all kinds of soil as below & disposal of excavated earth obtained to a distance up to 50m including all lift leveling, ramming the foundation trenches removing root of trees, shrubs all complete as per approved design. , e / w in soil item , e / w in soil item ( soft rock ) , providing p.c.c m 150 in nominal mix of ( 1:2:4 ) in foundation and plinth with approved quality of stone chips ( 30mm to 6mm size ) graded and clean coarse sand of f.m 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per specification and direction of e / i. , providing and casting in situ cement concrete of trap / granite / quartzite / gneiss metal of approved quality for rcc work in foundation like raft, grillage, strip foundation and footing of rcc columns and steel stanchions including normal dewatering, plywood formwork, bully / steel prop ups, compaction, finishing and curing, etc. complete. ( by weigh batching and mix design for m 300 only. ( excluding m.s, or tor ln rcc ) , total r.c.c in foundation , providing and casting in situ cement concrete of trap / granite / quartzite / gneiss metal for rcc work as per detailed drawing and designs or as directed by engineer in charge including normal dewatering, plywood formwork, bully / steel prop ups, compaction, finishing and curing, etc. complete. ( by weigh batching and mix design for m250 and m 300 only. ( excluding m.s, or tor ln rcc m 300 ) for columns , providing r.c.c.m – 250 with normal mix ofin beam of all types with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of f.m. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating , striking , curing , taxes and royalty all completed as per specification and direction of engineer in charge. , r.c.c in beam , providing r.c.c.m – 250 with normal mix ofin roof slab with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of f.m. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating , striking , curing , taxes and royalty all completed as per specification and direction of engineer in charge. , r.c.c in roof slab , providing and fixing gi pipe railing having 1.0m height consisting 50 x 50 x 6 mm thick m.s angles as vertical at 1.5 m c / c, and additional posts at every corner 3 rows of 25 mm dia g.i pipes fo medium class variety as horizontal and painting 3 coats of oil paint over 1 coat of anticorrosive paint of approved colour and shade including cost all labour, transporting bends to curved shape, etc.complete. , providing 12mm cement plaster ( 1:4 ) with clean coarse sand of f. m 1.5 including screening curing with cell leads and lifts of water b scaffolding taxes and royalty all complete as per building speciation and direction of e / i . , providing 2 coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, curing, scaffolding & taxes all complete as per building specification & direction of e / i. ( , providing t.m.t. reinforcement ( tor steel ) do as per specification and direction of e / i12mm tmt fe 500 , carriage of construction materials to work site including loading, unloading & stacking etc. all complete. , cement10km lead , steel10km lead , sand36km lead , stone / stone chips11km lead , coffer dam for intake and gangway , providing, constructing coffer dam in river basin / dam storages as per type design including excavation, fillingthe middle portion with b.c.soil ( in gunny bags if required ) .providing impervious / semimperviousmaterialson bothsideofb.c.soil ( in gunny bags if required ) including ramming, compacting to satisfaction of engineer in charge, till the completion of work including dismantling coffer dam after completionofworksand disposing offmaterialas directed by the engineer in charge. , for gangway , for intake well , dewatering the excavated trenches and pools of water in the building trenches / pipeline trenches, well works by using pumps and other devices including disposing off water to safe distance as directed by engineer in charge , for gangway , for intake well , mechanical & electrical work at intake well , doing geotechnical survey, collecting field data, designing, getting it approved by competent authority and rawwater pumping machinery with all complete job. , supply, installation, testing and commisssioning of vertical turbine pumpsets with allied equipment as under , supplying , erecting and commissioning of single / multi stage vertical turbine pump sets ( make: kirloskar / wpil / mather & platt ) as per is 1710, capable of discharging 16.62 lps against a head of 80m, consisting of bowl assemblies, bronze impellers, column assembly 60 ft hanged type stainless steel pump shaft, line shaft, etc. with all accessories coupled with energy efficient ( ie3 ) tefc squirrel cage induction motor confirming to is:325 and is:12615, having 15% more bhp than that of pump, operating on 1500 rpm, 415v, 3 ph, 50 hz [ make: kirloskar / abb / marathon / cgl ] all complete withrequired size of sluice valve and non return valve standard fitting, strainers, foot valve, reducer, pressure gauge, ms delivery, common header, nuts & bolts, packings, fitting & fixing, labour & technician, etc. all complete job as per site requirement and direction of e / i. ( note: contractor will have to check the design of pump & motor and get it approved by the department ) , discharging 16.62 lps, head 80m ( 1w + 1s ) 15 hp , providing , erecting and commissioning lt motor control panel board fabricated with ms sheet and painted, dust vermin proof. floor mounted cubical panel board shall be consisting of proper power distribution 250 a copper busbar 4 pole, 1 no. 250 a mccbas incoming feeder and 2 nos. 100a mccb as outgoing feeders for motors, 1 no. 100a mccb as spare feeder ( for motor ) , 2 no.32a & 63a mcb for lighting and other loads. includingselector switches, switch disconnector isolator, voltmeters, ampere meters, mfm, indicator lamps, internal wiring, danger board, protection units & relay, capacitor banks / apfc , suitable earthing set etc. all complete and as per is and direction of e / i . , supplying and erecting, assembled fully automatic star delta starter, in a provided cubical panel to operate squirrel cage induction motor working on 380 440 volt, 3 phase, 50 hz with no volt coil, over load relay and on / off push buttons, with necessary material and connected to supply, etc complete. , 40 hp , power wiring with required 120 sq mm 3.5 core 1.1 kv grade armoured aluminium cables, xlpe / pvc insulated armoured cable from transformer to mcp at raw water pump house.laying, jointing and making proper terminations, etc.all complete. , power wiring with required 25 sq mm 3 core 1.1 kv grade armoured copper cables, xlpe / pvc insulated armoured cable from power distribution panel ( mcp ) to motors, including laying on wall or on floor as where required, jointing and making proper terminations, etc.all complete. , providing, erecting for each motor with all required materials, etc.all complete. , providing / erecting servo controlled automatic voltage stebilizer suitable for out put voltage of 415 volt+ / 1% 3 phase 50 hz, with copper wound input ( 280 450 ) volt transformer ( oil cooled ) as mentioned below.the stabilizer shall function satisfactorily even if incoming supply is unbalanced between phases within range of 10%.the stabilizer should be constructed in cubical box, with bi directional wheels for easy handling, necessary monitors and users controls on front panel such as indication, alarm, voltmeter and selector switch for measuring input and ouput voltage, auto / manual selector switch, raise / low push buttons etc.suitable capacity termination strips and bus bars for incoming and out going cable should be provided.all three phases shall be independently monitored and corrected.following protections and indications shall be incorporated etc.all complete job, including change over switch, t oil, etc.all complete with required accessories and materials. , 75 kva , providing, erecting and commissioning3t triple type chain pully block suitable as below with 6m lift complete with laoad chain and hand chain suitable for avove lift, tested 50% over load as per is 3832 carry isi mark with travelling trolley etc. all complete job as per the site requirement and indian standard , lighting doinginternal and external lighting by doing wiring and installing lumenaries e.g. suitable wattage led light fittings with standard lumen in pump house, gangway etc all complete for raw water pumping plant, including lightening arrester, fire extingusher, first aid box, rubber matting panel, shoes, gloves, helmet etc.as per the direction of e / i. , ( mechanical & electrical part at wtp ) , doing geotechnical survey, collecting field data, designing, getting it approved by competent authority and clear waterc.f. pump with all complete job , suply, installation, testing and commisssioning of horizontal casing centrifugal pumpsets with alied equipment as ( please refer to section 5, sl.2.5of sbd ) , providing , erecting and commissioning of horizontal split casing / multi stage centrifugal pump ( make: kirloskar / wpil / mather & platt ) as per is:5120, capable for discharging 16.62 lps against a head of 40m , consisting of bronze impellers, stainless steel pump shaft, etc. with all accessoriescoupled with energy efficient ( ie3 ) tefc squirrel cage induction motor confirming to is:325 and is:12615, having 20% more bhp than that of pump, operating on 1500rpm, 415v, 3 ph, 50 hz [ make: kirloskar / abb / cgl / marathon ] all complete withrequired size of sluice valve and non return valve standard fitting, strainers, reducer, foot valve, pressure gauge, ms delivery & suction pipe, common header, nuts & bolts, packings, fitting & fixing, labour & technician, etc. all complete job as per site requirement and direction of e / i. ( note: contractor will have to check the design of pump & motor and get it approved by the department ) , discharge16.62 lps and head 40 m ( 1w+1s ) , , providing , erecting and commissioning lt motor control panel board fabricated with ms sheet and painted, dust vermin proof. floor mounted cubical panel board shall be consisting of proper power distribution 100 a copper busbar 4 pole, 1 no. 100 a mccbas incoming feeder and 2 nos. 63a mccb as outgoing feeders for motors, 1 no. 63a mccb as spare feeder ( for motor ) , 2 no.32a & 63a mcb for lighting and other loads.2 no.100a mccb for wtp equipments. includingselector switches, switch disconnector isolator, voltmeters, ampere meters, mfm, indicator lamps, internal wiring, danger board, protection units & relay, suitable earthing set etc. all complete and as per is and direction of e / i , supplying and erecting, assembled fully automatic star delta starter, in a provided cubical panel to operate squirrel cage induction motor working on 380 440 volt, 3 phase, 50 hz with no volt coil, over load relay and on / off push buttons, with necessary material and connected to supply, etc complete. , 20 hp , power wiring with required 50 sq mm 3.5 core 1.1 kv grade armoured aluminium cables, xlpe / pvc insulated armoured cable from transformer to mcp at clear water pump house.laying, jointing and making proper terminations, etc.all complete , power wiring with required 10 sq mm 3 core 1.1 kv grade unarmoured copper cables, xlpe / pvc insulated armoured cable from power distribution panel ( mcp ) to motors, including laying on wall or on floor as where required, jointing and making proper terminations, etc.all complete.. , providing, erecting earthing for each motor with all required materials, etc.all complete.as per is 3043. , providing / erecting servo controlled automatic voltage stebilizer suitable for out put voltage of 415 volt+ / 1% 3 phase 50 hz, with copper wound transformer ( air cooled ) as mentioned below.the stabilizer shall function satisfactorily even if incoming supply is unbalanced between phases within range of 10%.the stabilizer should be constructed in cubical box, with bi directional wheels for easy handling, necessary monitors and users controls on front panel such as indication, alarm, voltmeter and selector switch for measuring input and ouput voltage, auto / manual selector switch, raise / low push buttons etc.suitable capacity termination strips and bus bars for incoming and out going cable should be provided.all three phases shall be independently monitored and corrected.following protections and indications shall be incorporated etc.all complete job, including change over switch, earthing, etc. , 50kva , providing, erecting and commissioning 3ttriple spur type chain pulley block suitable as below with 6m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per is 3832 carry isi mark with travelling trolley etc. all complete job as per the site requirement. , providing erecting fire extingusher andfirst aid box, lightening arrester for pump house, rubber matting ( 2nos. ) for electrical equipments, tools & tackles, etc.complete job. , raw water rising main. , doing geotechnical survey, collecting field data, designing, getting it approved by competent authority and laying of raw water rising main. , di pipe for water works with socket & spigot ends in standard working lengths of 4.5, 5.5 & 6 m for classification k 9 suitable for push on joint ( rubber gasket d jointing ) with cement mortar lining inside the pipes with outside zinc and bituminous coating ( including cost of one no gasket for each pipe ) note:the rates are for jharkhand at ranchi but exclusive of gst & cp , 200mm dia , earth work in excavation ( as per is. 3114 / 1965 ) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of engineer in charge , soil item class b , soil item class c , earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of engineer in charge ( for classification for soil item a&b ) , providing and supplying of isi standard d.i specials & fitting with sealing rubber gasket of s.b.r complete with cast iron follower gland and m.s nutbolts coated or otherwise protected from rusting and suitable for d.i pipescomplete as per is 9523 class k 12 ( ex factory rates ) inspection charge transportation, cp extra. , labour charge for one cutting of cast iron pipe and specials including supplying necessary tools and plants, chipping of filling the surface finish as per specification and direction of e / i. , 200mm dia pipe , supplying labour tools and tackles for testing of laid ci or upvc or hdpe or ac pressure pipe up to 60meter head of water all complete as per specification and direction of engeneer in charge. water to supplied free of cost departmentally. , 200mm dia pipe , providing double flanged sluice valve confirming to is 2906 / 14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all taxes transportation etc. complete. ( without by pass arrangement pn 1.6 ) , 200 mm dia , 150 mm dia scour valve , providing and supplying air valve as per is 14845 2000 and mjps standard specification of approved make & quality of following diameters including all taxes ( central and local ) , railway freight, insopection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores / sites unloading and stacking etc. complete.depatmental. ( single ball double flanged pn: 1.6 ) , 40mm dia air valve , lowering, laying and fixing in proper alignment and position all type of c.i air valves as directed by engineer in charge including cost of conveyance from store to site of work, cost of all materials and giving satisfactory hydraulic testing etc. complete ( for all class of valves ) .air valve singe ball ( pn 1 and pn 1.6 ) 40 mm dia , supplyng labour and tools for fixing c.i. sluice valve in trenches with a pair of c.i tail pieces incluidng making lead caulked joints and flenged joints as per i.s specification, including supplying all jointing materials ( pig lead confirming to i.s.s 782 1978, yarn confirming to i.s.s 6587 1972 and nuts and volts confirming to i.s.s 1364 1983 ) including drillig holes in flanges if required as per specification and direction of e / i. , 150 mm dia scour valve , 250 mm dia s.v. , construction of brick masonary valve chamber of size ( 1.20 m x 0.90 m x 1.50 m ) ( sluice valve + air valve ) and deatil attched analysis , construction of thrust blocks for rising main , supplying labours, tools, tackles, lubricant etc. for laying and jointing d.i / c.i. s / s tyton pipes ( class la ) trenches withoutsupplying rubber gasket and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete . laying of pipe is to be done as per i.s.s 3114 1985 as per deisgn, specification and direction of e / i. , 200mm dia , clear water rising main. , doing geotechnical survey, collecting field data, designing, getting it approved by competent authority and laying of clear water rising main. , di pipe for water works with socket & spigot ends in standard working lengths of 4.5, 5.5 & 6 m for classification k 9 suitable for push on joint ( rubber gasket d jointing ) with cement mortar lining inside the pipes with outside zinc and bituminous coating , 200 mm dia , earth work in excavation ( as per is. 3114 / 1965 ) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of engineer in charge , soil item class b , earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of engineer in charge. ( for classification for soil item a&b ) , providing and supplying of isi standard d.i specials & fitting with sealing rubber gasket of s.b.r, complete with cast iron follower gland and m.s nut & bolts coated or otherwise protected from rusting and suitable for d.i pipescomplete as per is 9523 class but excluding freight. , labour charge for one cutting of cast iron pipe and specials including supplying necessary tools and plants, chipping of filling the surface finish as per specification and direction of e / i. , 200mm , supplying labour tools and tackles for testing of lead ci or upvc or hdpe or ac pressure pipe up to 60meter head of water all complete as per specification and direction of engeneer in charge. , 200 mm , providing double flanged sluice valve confirming to is 2906 / 14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all taxes transportation etc. complete. ( without by pass arrangement pn 1.6 ) , 200 mm , construction of thrust blockfor rising main pipe ( analysis attached ) , supplyng labour and tools for fixing c.i sluice valve in trenches with a pair of c.i tail pieces incluidng making lead caulked joints and flenged joints as per i.s specification, including supplying all jointing materials ( pig lead confirming to i.s.s 782 1978, yarn confirming to i.s.s 6587 1972 and nuts and volts confirming to i.s.s 1364 1983 ) including drillig holes in flanges if required as per specification and direction of e / i. , 200 mm dia , construction of brick masonary sluice valve chamber of size ( 1.20 x0.90 x 1.50 ) m ( sluice valve + air valve +n.r valve ) and deatil attached. , supplying labours, tools, tackles, lubricant etc. for laying and jointing d.i / c.i. s / s tyton pipes ( class la ) trenches without supplying rubber gasketand making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete ( pipe to be supplied departmentally free of cost and laying of pipe is to be done as per i.s.s 3114 1985 as per deisgn, specification without rubber gasket and direction of e / i. , 200 mm , providing installing and giving satishfactory field testing of bulk water meter, horizontal inferential multijet type with magnetic device and dry dial suitable for ambient 500 c temperature duly seeled against tempering complete with flenges at both ends and confirming to class b as per iso 4064 along with manufacture is test cartificate and guarantee certificate, including cost of all materials and labour etc.with oiml.mld certification for abroad meter and fcri for india including 36 months guarantee etc.all complete. ( removable mechanism type bulk water meter ) , 200 mm dia , distribution system , doing geotechnical survey, collecting field data, designing, getting it approved by competent authority and providing all labour, materials, equipment to procure and laying of pipes for distribution main . , di pipe for water works with socket & spigot ends in standard working lengths of 4.5, 5.5 & 6 m for classification k 7 suitable for push on joint ( rubber gasket d jointing ) with cement mortar lining inside the pipes with outside zinc and bituminous coating ( including cost of one no gasket for each pipe ) , 100 mm dia pipe , 150 mm dia pipe , 200 mm dia pipe , 250 mm dia pipe , providing and supplying high density polythene pipe ( hdpe pipe ) of 20mm to 500mm outer dia suitable for water supply which is avaliable in all standards like isi 4984, iso 4427, din 8074 and various grades like pe 63, pe 80, pe 100 and newly invented pe 100+materials ( b hdpe pipe of materials grade pe 100 pn 10 ( dia in mm ) , id 52.4 / 63 mm od , id 62.4 / 75 mm od , providing and supplying isi standard d.i specials & fitting with sealing rubber gasket of s.b.r, complete with cast iron follower gland and m.s nutbolts coated or otherwise protected from rusting and suitable for d.i pipescomplete as per is 9523. , for 100 mm to 250 mm dia pipe , earth work in excavation ( as per is. 3114 / 1965 ) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of engineer in charge ( classification soil item b ) , e / w in excavation of cut off trenches as per designed section in soft rock or ordinary rock ( where blasting is not needed ) ( vide classification of soil item c with disposal of spoil ( beyond 50m away from the toe of dam in country side ) with initial lead of 60m and lift of 1.5m, including making the section in profile, dressing sides in proper slope and bed in proper grade etc. all complete as per specifictaion and direction of e / i. , supplying labours, tools, tackles, lubricant etc. for laying and jointing d.i / c.i. s / s tyton pipes ( class la ) trenches supplying rubber gasket and making gasket joints including providing night guard, barrier and red light to safe guard against accident, all complete and laying of pipe is to be done as per i.s.s 3114 1985 as per deisgn, specification and direction of e / i. ( without rubber gasket ) , 100 mm , 150 mm , 200 mm , 250 mm , 63 mm , 62.4 / 75 mm hdpe , supplyingtool and cutting road as well restoring the same as per specification and direction of e / i , pucca road ( except black top only taken out materials to be used ) , water bound macadam road ( taken out materials to be used ) , dismentaling plain cement or lime concrete work including stacking , providing pcc m 150 in nominal mix of ( 1:2:4 ) in road with approved quality of stones chips 20 mm 6mm size graded and clean coarse sand fm 2.5 to 3.0 including screening shuttering mixing cmenet concrete in mixer and placing in position vibrating striking curing taxes and royalty all complete as per building specification and direction of e / i. , labour charge for one cutting of cast iron / di pipe and specials including supplying necessary tools and plants, chipping of filling the surface finish as per specification and direction of e / i. , 100mm , 150mm , 200mm , 250mm , id 52.4 / 63 mm od , id 62.4 / 75 mm od , providing double flanged sluice valveconfirming to is 2906 / 14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. all complete ( pn 1 without bypass arrangement ) , 100 mm , 150 mm , 200 mm , 250 mm , supplyng labour and tools for fixing c.i sluice valve in trenches with a pair of c.i tail pieces incluidng making lead caulked joints and flenged koints as per i.s specification , including supplying all jointing materials ( pig lead confirming to iss 782 1978, yarn confirming to is.s 6587 1972 and nuts and volts confirming to i.s.s 1364 1983 ) including drillig holes in flanges if required as per specification and direction of e / i. , 100mm , 150mm , 200mm , 250 mm , earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of engineer in charge. ( for classification for soil item a & b ) , construction of b.w. masonary valve chamber of size 1.20 m x 0.90 m x 1.50 m ( sluice valve ) and detailed attched , supplying tools and tackles for testing of laid c.i or upvc or hdpe or ac or di pressure pipe up to 60 meter head of water all complete as per specification and direction of engeneer in charge. , 100 mm , 150mm , 200mm , 250mm , id 52.4 / 63 mm od , id 62.4 / 75 mm od , boundary / compound wall ( boundary wall =196.40 m ) , doing geotechnical survey, collecting field data, designing, getting it approved by competent authority construction of compound wall. etc. all complete job. , earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item b ) and disposal of excavated earth so obtained to a distance upto 50 m including all lifts, levelling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of e / i. excavation qty. , providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of e / i. ( mode of measurement compacted volume ) . , providing designation of 75a one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of e / i. , providing p.c.c m 150 in nominal mix of ( 1:2:4 ) in foundation with approved metal grade iii ( 20mm to 6mm size ) quality of stone clean course sand of f.m 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of e / i.qnty in foundation: , providing r.c.c m 200 in nominal mix of ( 1:1.5:3 ) in foundation with approved stone aggregate ( 20mm to 6mm size ) quality of stone clean course sand of f.m 2.5 to 3 including screening, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of e / i.qnty in foundation: , centering and shuttering , providing r.c.c m 200 in nominal mix of ( 1:1.5:3 ) instiffners with approved stone aggregate ( 20 mm to 6mm size ) quality of stone clean course sand of f.m 2.5 to 3 excluding screening, mixing cement concrete in mixer and placing in position, vibrating, striking, curing ( but excluding the cost of reniforcement , taxes and royalty all complete as per building specification and direction of e / i. , qnty , centering and shuttering , providing r.c.c m 200 in nominal mix of ( 1:1.5:3 ) in bond at plinth level with approved stone aggregate ( 20 mm to 6mm size ) quality of stone clean course sand of f.m 2.5 to 3 excluding screening, mixing cement concrete in mixer and placing in position, vibrating, striking, curing ( but excluding the cost of reniforcement , taxes and royalty all complete as per building specification and direction of e / i. , centering and shuttering , providing r.c.c m 200 in nominal mix of ( 1:1.5:3 ) inband at lintel level with approved stone aggregate ( 20 mm to 6mm size ) quality of stone clean course sand of f.m 2.5 to 3 including screening, mixing cement concrete in mixer and placing in position, vibrating, striking, curing ( but excluding the cost of reniforcement , taxes and royalty all complete as per building specification and direction of e / i. , centering and shuttering , providing designation 75 a brick work in cm ( 1:6 ) in super structure with approved quality of clean coarse sand of fm 2 to 2.5 including, providing 10mm thick mortar joints cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of e / i. , qnty. wall , providing 12mm thick cement plaster ( 1:6 ) with clean coarse sand of fm 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direction of e / i. , qnty.wall , providing two coats of snow cerm of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper , scaffolding, curing and taxes all complete as per building specification & direction of e / i. . , providing tor steel reinforcement of 10 mm , 12 mm , &16 mm dia bars as per approved design and drawing excluding carriage of m.s bars to work site , cutting , bending and binding with annealed wire with cost of wire , removal of rust , placing the rods in position all complete as per building specification and direction of e / i , qty , filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with lead of 50m and lift of 1.5 m all complete as per building specification & direction of e / i , carriage of construction materials to work site including loading, unloading & stacking etc. all complete. , cement10km lead , steel10km lead , sand36km lead , bricks6km lead , stone / stone chips11km lead , cost of gate ( 1 nos ) , earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item b ) and disposal of excavated earth so obtained to a distance upto 50 m including all lifts, levelling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of e / i. excavation qty. , providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of e / i. ( mode of measurement compacted volume ) . , providing designation of 75a one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of e / i. , providing p.c.c m 150 in nominal mix of ( 1:2:4 ) in foundation with approved stone aggregate ( 20mm to 6mm size ) quality of stone clean course sand of f.m 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of e / i.qnty in foundation: , providing r.c.c m 200 in nominal mix of ( 1:1.5:3 ) in foundation with approved stone aggregate ( 20mm to 6mm size ) quality of stone clean course sand of f.m 2.5 to 3 including screening, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of e / i. , centering and shuttering , providing r.c.c m 200 in nominal mix of ( 1:1.5:3 ) in column with approved stone aggregate ( 20mm to 6mm size ) quality of stone clean course sand of f.m 2.5 to 3 including screening, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of e / i. , centering and shuttering , providing r.c.c m 200 in nominal mix of ( 1:1.5:3 ) in band at plinth level with approved stone aggregate ( 20mm to 6mm size ) quality of stone clean course sand of f.m 2.5 to 3 excluding screening, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of e / i. , centering and shuttering , providing tor steel reinforcement of 10 mm , 12 mm , &16 mm dia bars as per approved design and drawing excluding carriage of m.s bars to work site , cutting , bending and binding with annealed wire with cost of wire , removal of rust , placing the rods in position all complete as per building specification and direction of e / i , filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with lead of 50m and lift of 1.5 m all complete as per building specification & direction of e / i , supplying fitting & fixing m.s grill gate with m.s grills made 20x6mm m.s flat or 16mm m.s square bars fitted 25x25x6mm m.s angle farme of size 60x60x6 mm including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in p.c.c ( 1:2:4 ) blocks of required size, applying a priming red lead paint over steel work , taxes all complete as per direction of e / i. , qnty. , providing two coats of painting with ready mixed paint of approved shade and make over steel surface , carriage of construction materials to work site including loading, unloading & stacking etc. all complete. , cement10km lead , steel10km lead , sand36km lead , bricks6km lead , stone / stone chips11km lead , staff quarters , doing geotechnical survey, collecting field data, designing aesthetically, getting it approved by competent authority and provision of twin type staff quarter etc. all complete job. , e / w in excavation in foundation trenches in hard soil ( vide classification of soil item a ) and includingall lift leveling, rammingthe foundation trenches removing roots of trees, shurbs all complete as per approved design, building specification and direction of e / i. , providing, coarse clean sand in filling in foundation trenches / in plinth including ramming & watering in layers not exceeding 150mm thick with all leads, including cost of materials, labour, royalty & taxes all complete as per building specification & direction of e / i. ( mode of measurement compacted volume ) . , providing designation 75 a one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of e / i. , providing p.c.c.m 100 in nominal mix of ( 1:3:6 ) in foundation with approved quality of stone metal grade iii ( 50 mm to 25 mm size ) graded andclean coarse sand of f.m.2.5 to 3 including screening, shu ttering , mixing cement concrete in mixer & placing in position, vibrating, striking, curing, taxes & royalty all complete as per building specification & direction of engineer in charge. , providing designation 75a brick work in c.m. ( 1:6 ) in foundation & plinth with approved quality of clean coarse sand of f.m. 2 to 2.5 including providing 10 mm thick mortar joints, costs of screening, materials, scaffolding, raking out joints to 15 mm depth curing, taxes & royalty all complete as per building specification & direction of e / i. , providing 50 mm thick damp proof coarse with cement concrete m 150 with nominal mix of ( 1:2:4 ) with approved quality of stone chips of 20 mm to 6 mm size graded and clean coarse sand of f.m.2.5 to 3 including screening, shuttering, mixing cement concrete in mixer with 5 %cico or any other approved water proofing compound and placing in position, striking, curing, taxes & royalty all complete as per building specification & direction of e / i. , providing designation 75 a brick work in c.m. ( 1:6 ) in superstructure with approved quality of clean coarse sand of f.m. 2 to 2.5 including providing 10mm thick mortar joints, costofscreening, materials scaffolding, raking out joints to 15 mm depth curing, taxes & royalty all complete as per building specification & direction of e / i. , providing r.c.c.m 200 with nominal mix of ( 1:1.5:3 ) in lintel with approvedquality of stone ships 20 mm to 6 mm size graded & clean coarse sand of f.m. 2.5 to 3 excluding screening, centering, shuttering, mixing cement concrete in mixer & placingin position vibrating, striking, curing ( but excluding the cost of reinforcement ) , taxes & royalty all complete, as per building specification and direction of e / i. , centering and shuttering , providing average 63 mm thick r.c.c.m 200 with nominal mix of ( 1:1.5:3 ) chajja & in shelves with approved quality of stone chips 20mm to 6mm size graded & clean coarse sand of f.m. 2.5 to 3 including making drip course in concrete, screening, centering, shuttering& mixing cement concrete in mixer & placing in position vibrating, striking, 6 mm cement plaster ( 1:4 ) in ceiling & sides of chajja with sand of f.m. 1.5, curing ( but excluding the cost of reinforcement ) taxes and royalty all complete as per building specification of e / i. , centering & shuttering doors window , centering & shuttering shelves , providing r.c.c. m 150 with nominal mix of ( 1:2:4 ) in roof slab with approved quality of stone chips 20 mm to 6 mm size graded & clean coarse sand of fm 2.5 to 3 excluding screening, centering, mixing cement concrete in mixer & placing in position, vibrating, striking, curing ( but excluding the cost of reinforcement ) taxes & royalty all complete as per building specification & direction of the e / i. , centering & shuttering shelves , supplying, fitting & fixing good quality, well dressed & well seasoned sal wood work in chaukhat in doors, windows, skylights, fanlights and c / w celestial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls & lintels all complete as per building specification & direction of the e / i. , supplying fitting and fixing 250 x 20 x 6 mm l type m.s. clamp properly fish tailed, including making holes and setting the same in 375 x 125 x 75 mm cement concrete block ( 1:2:4 ) with cost ofall labour and materials and taxes as per building specification and direction of e / i . , supplying all material, labour, fitting & fixing 38mm thick good quality well dressed and well seasoned sal wood battened shutter ledged & braced in doors and windows with oxidized iron fitting such as hinges, sliding door bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand block as per schedule, taxes & royalty all complete as per building specification & direction of e / i. , supplying, fitting & fixing m.s. grill made of 20 x 6mm m.s. flat as per approved design & drawing properly fabricated with joints continuous fillet welded and finishedsmooth, carriage of grill to work site, hoisting as per the building specification and direction of e / i. ( wherematerialsisnot supplied by the deptt. ) , 40kg / sqm ( 40x7.56m2 ) , providing 40 mm thick precast r.c.c. m 150 with nominal mix of ( 1:1.5:3 ) in jali with approved quality of stone chips of 6 mm nominal size and clean coarse sand of fm 2.5 to 3 with 1.6 mm thick m.s. wire as per approved design and drawing and placing the same in position true to plumb and level and properly grouted with cement mortar ( 1:3 ) including cost of curing, scaffolding and finishing all complete as per building specification and direction of e / i. , providing and fixing fan hook of 16 mm dia m.s. bar 1 meter long bent to required size and shape, placed in position and fixing in r.c.c. slab / beam at thetimeofcasting allcomplete as per building specification anddirection of e / i. ( where material is not supplied by deptt. ) . , supplying fitting and fixing m.s. grill gate with m.s. grills made of20 x 6 mm m.s. flat fitted on 25 x 25 x 6mm. m.s. angle frame as per approved design & drawing, properly fabricated with joints continuous fillet welded & finished smooth, providing necessary locking arrangement with haskal and domny duly fixed in p.c.c. ( 1:2:4 ) blocks of required size, applying priming red lead paint over steel work, taxes all complete as per drawing specification and direction of e / i. ( when steel is not supplied by the deptt. ) , providing 6 mm thick cement plaster ( 1:4 ) in ceiling with clean coarse sand of f.m. 1.5 includingscreening, curing with allleads&liftsofwater, scaffolding, taxes & royalty all complete as per building specification & direction of e / i. , providing 12 mm thick cement plaster ( 1:6 ) withcleancoarse sand of f.m.1.5including screening, curing with all leads & lifts of water, scaffolding, taxesand royalty all complete as per buildingspecification& direction of e / i. , providing 12mm cement mortar ( 1:3 ) with clean coarse sand of f.m. 1.5 with floating coat of neat cement punning in skirting including rounding of junction with floor, curing with all leads & lifts of water , scaffolding , taxes and royaltyall completeas per buildingspecification & direction of e / i , filling in foudation trenches & plinth in layersnot exceeding 150 mm thick well watered , rammed , fully compacted & finedressed with earth obtained fromexcavation of foundationtrencheswithin a lead of 50 m & lift of 1.5 m all complete as per building specification & direction of e / i ( mode of measurementcompacted volume ) , providing 25 mm thick . first class patent stone flooring ( 1:2:4 ) with stone chips in two layers , bottom layer 19 mmthick ( 1:2:4 ) with 12 mm to 6 mm size graded stone chips and top layer 6 mm thick ( 1:2 ) with 6 mm down stone chips in pannels including cost of curing , finishing the surface smooth by rubbing with carborandum stone taxes & royalty with all completeas per building specification & direction of e / i , providing designation 75 a one brick on edge flooring in c.m ( 1:4 ) with top surface flush pointed in cm ( 1:4 ) approvedquality of clean coarsesand of f.m 2 to 2.5 including the cost of screening , raking outjointsto 15 mm depth , curing taxes, royalty all complete as per building specification and direction ( e / i ) , providing two coated of snowcem of approved shade and make over a coat of cement primer on new surface including cost of cleaningsurface, scaffolding etc.all complete. , color washing two coats over a coats over a coat of white wash over new surface with approved quality of lime in approved shade including the cost of cleaning surface thoroughly and removing the scales of smoke & mosh marks with jhama rubbing, scaffolding washing of floors and taxes all complete as per building specification and direction of e / i. , providing two coats of painting with ready mix paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt, scales, smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification & direction of e / i. , providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning , removing rust , dirt , scales , smokes and grease and cleaningthe surface thouroughly including cost of scaffolding and taxes all complete as per building specification and direction of e / i , providing two coats of painting with ready mix paint of approved shade & make over steel surface including cleaning the surface thoroughly, scaffolding & taxes all complete as per building specification & direction of e / i. , providing tor steel reinforcement of 8mm dia as per approved design and drawing excluding carriage of bars to work site , cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per specification and direction of e / i.tmt fe 500 ( only validfor sail and tata ) , carriage of construction materials to work site including loading, unloading & stacking etc. all complete. , cement10km lead , steel10km lead , sand36km lead , bricks6km lead , stone / stone chips11km lead , water supply sanitation installation ( plumbing work ) , supplying and laying gi pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes in size and threading ends where necessary including carriage of materials up to work site etc. all complete as per specification and direction of e / i. , i ) 25mm gi. pipe. , ii ) 15 mm gi. pipe. , supplying materials labours and tools for fixing gi pipes with red lead paints and yarn with screwed and sockted joints on wall, celling and floor including supplying of wall hooks of pipe clamp, wooden plugs, cutting pipe to size and threading ends where necessary all complete as per specification and direction of e / i. , i ) 15 mm gi. pipe , supplying, fitting and fixing of gm ferrule of approved make in di / ci main including drilling and tapping ci / di main etc. all complete as per specification and direction of e / i. , supplying and fixing gi fittings of approved make all complete as per direction of e / i. , ( a ) elbow 15 mm dia , ( b ) tee plane 15mm dia , ( c ) nipple 15mm dia. , ( d ) union socket 25mm dia , ( e ) union socket 15mm dia , ( f ) brass bib cock15mm dia , ( g ) c.i stop cock 15mm dia , ( h ) c.i. stop cock 25mm dia , ( i ) reducing socket 25x15mm , ( j ) tee 25x25x15mm dia , supplying, fitting and fixing vitreous white glazed earthen were i w c of parry hindustan or any other i.s.s approved make with 100 mm hci ‘p’ trap, 15 liters ci pull and let go flushing cistern of names or otheriss equivalent make complete with all fittings c.i. or c.c brackets, 32 mm, alkathene / pvc telescopic flush pipe about 2 mtrs. long with one brass coupling and clamps, gi chain and pull including supplying and fixing a pair of vitreous white glazed earthen were footrest to be fixed in floor, 15 mm .ci body brass spindle, stop cock of weight not less than 50 grams, 15 mm. pvc connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of e / i. ( 510mm.long with 12.5 liter low level pvcsystem ) . , septic tankand soak pit , earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item b ) and disposal of excavated earth as obtained to a distance up to 50 m including all lifts, leveling, ramming the foundation trenches, removingrootsoftrees, shrubsall complete as per approved design, building specification and direction of e / i. , providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of e / i. , providing designation 75a one brick flat soling, joints filled with local sand including cost of watering, tax, royalty all complete as per building specification and direction of e / i. , providing p.c.c m150 with nominal mix of ( 1:2:4 ) in foundation with approved stone chips 20mmto 6mm size well graded andclean course sand of fm 2.5to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of e / i. , providing water proof cement plaster ( 1:3 ) with clean course sand of f.m 1.5mm with 5% cico or any other approved water proofing compound including taxes and royalty all complete as per buildingspecification and directions of e / i. , ( a ) 19 mm thick , ( b ) 12 mm thick , providing designation 75a bricks work in c.m. in foundation and plinth with approved quality of clean coarse sand of f.m. 2 to 2.5 including providing 10mm. thick mortar joints, cost of screening materials racking out joints to 15 mm. depth, curing taxes and royalty all complete as per building specification and direction of e / i. , ( a ) b / win c.m ( 1:4 ) , ( b ) b / w 75 b in ( 1:6 ) for soak pit , ( c ) brick work in dry masonry for soak pit. , providing pre cast r.c.c.m 150 with nominal mix of ( 1:2:4 ) slab of desired sizewith approved quality of stone chipsand clean coarse sand of fm 2.5 to 3 including curing, shuttering, carrying the slab manually to site and laying in position all complete ( but excluding the cost of reinforcement ) , taxes and royalty etc. all complete as per building specification and direction of e / i. , providing tor reinforcement as per approved design and drawing excluding carriage of tor rod to work site including cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per specification and direction of e / i. , 10 mm dia , supplying fitting and fixing h.c.i. pipe / h.c.i. fitting of approved make confirming to i.s.s 1729 including supplying nails and bobbins lead andyarn from making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of e / i. , ( a ) 100mm dia h.c.i. tee. , ( b ) 100mm dia h.c.i. band , ( c ) 50mm dia h.c.i. cowel , ( d ) 50mm dia h.c.i. vent pipe , ( e ) 100mm h.c.i. pipe , supplying materials and labours and fixing20mm dia m.s bar steps in wall of 0.3 m interval and staggeredin ( 1:2:4 ) cement concrete including scaffolding and curing etc. all complete as per specification and direction of e / i. , supplying all materials, labours, tools and tackles and 100mm dia r.c.c hume pipe and laying jointing, testing, earth work including carriage of materials etc. all complete. , supplying 50mm size brick bats and filling in soak pit including carriage and labours etc. all complete as per direction of e / i. , supplying materials and labours for constructing inspection chamber of designation class 75 b bricks size 750mm deep, 600x450mm internal dimension having 250mm wall thickness in cement mortar ( 1:6 ) including 12mm cement plaster ( 1:4 ) with punning on inside and cement plaster ( 1:6 ) with 600x475 mm g.i. cover with frame ( weight not less than 36 kg. ) along with earth work in excavation and 80mm thick p.c.c. ( 1:3:6 ) in foundation and refilling all complete as per specification and direction of e / i , carriages of materials , ( a ) brick –6 km lead , ( b ) sand 36 km lead , ( c ) stone chips 11 km lead , ( d ) steel 10 km , ( d ) cement 10 km lead , electrical works , point wiring in pvc conduit with modular type switch wiring for light point / fan point with 1.5sqmm f.r. pvc insulated copper conductor single core cable in surface / recessed pvc conduit with modular switch modular plate, suitable g.i. box and the point with sqmm fr pvc insulated copper conductor single core cable etc as required , wiring for twin control light point with 1.5 sqmmf.r. pvc insulated copper conductor single core cable in surface / recessed pvc conduit with two way modular switch modular plate, suitable g.i. box and the point with sqmm fr pvc insulated copper conductor single core cable etc as required , wiring for light / power plug point with 2 x 4 sqmm f.r. pvc insulated copper conductor single core cable in surface / recessed pvc conduit along with one no 4 sqmmfr pvc insulated copper conductor single core cable for loop earthing etc as required , coppersub main wiring in pvc conduit wiring for sub main wiring withpvc insulated copper conductor single corein surface / recessed pvc conduitas required , 2 x 1.5 sqmm + 1 x 1.5 sqmm earth wiring , 2 x 2.5 sqmm + 1 x 2.5 sqmm earth wiring , supplying and fixing following way three pole and neutral sheet mcb distribution board 415 volts on surface / recessed complete with tinned copper bush bars , neutral link, earth bar, din bar, detachable gland plate inter connection phosphatised and power painted including earthing etc as required ( but with out mcb / rccb / isolator ) ( 4 +12 ) double door horizontal type , supplying and fixing 5 amp to 32 amp, rating 240 volts, b series miniature circuit breaker of single poles in existing mcb db complete with connecting , testing, and commissioning etc as required , earthing with g.i. earth pipe 4.5 m long 40mm diaincluding accessories and providing masonry enclosure withcopperplate having locking arrangement and watering pipe etc with charcoal , salt all complete as per electrical rule , supplying , fitting and fixing following sizes of pvc conduct along with accessories in surface / races including cutting the wall and making good the same in case of recessed conduit as required , pvc con 20 mm pvc pipe , pvc con 25 mm pvc pipe , installation commissioning and testing ceiling fan , carriage of ceiling fan and regulator , supplying , fitting and fixing 5 amp ceiling rose on the existing junction , supplying , fitting and fixing breas batten / angle holder including connection etc. , supplying , fitting and fixing g.i. box with modular plate and cover in front of surface or in recess including providing and fixing 3pin 5 / 6 amp modular type switch, connection, painting etc as required. , supplying , fitting and fixing g.i. box with modular plate and cover in front of surface or in recess including providing and fixing 6pin 5 / 6 amp and 15 / 16 amp socket outlet and 15 / 16 amp modulartype switch, connection, painting etc as required. , supplying and drawing co axial t.v. cable rg 06 grade 0.7 nn solid copper conductor pe insulated seilded with fine tinned cover braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , supplying and fixing modular switch / socket on the existing modular plate and switch box including connection but excluding modular plate etc, as required. tv antenna socket out put , supplying , fitting and fixingmodular base andcover plate on existing modular metal boxes etcas required. , cost ofearthing with g.i. earth pipe 4.5 m long 40mm diag.i.pipe 600mm x 600mm x 6mm thick copper earth plate, and 8 swg copper wire including cost of making 1.2x1.2x3m deep pit and filling with charcoal , salt all complete as per electrical rule , house connection 1628 no. of house + 12 no. of school and anganwadi =1640 , earth work in excavation exacavation in foundation trenches in hard soil vide classification item b and disposal of exacavated earth as obtained to a dist. upto 50m including all lifts, levelling, ramming the foundation trenches, removing roots of tree, shrubs all complete as per approved design, building specification and direction of e / i. , providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labours.royality and taxes all complete as per building specification and direction 0f e / i. ( mde of measurement compacted volume ) , providing a pcc m 150 in nominal mix of ( 1:2:4 ) in foundation with approved quality of stone chips 20mm to including screening, shutteing, mixing cement concrete in mixer and placing a position, vibrating, striking, curing, taxes and loyality complete all as per building specification and direction of e / i , centering & shuttering ( below gl ) , centering & shuttering ( above gl ) , earth work in backfilling the trenches after laying different types and size of pipes with earth removed during exacavation within initials leads and lifts as per building specification and direction of e / i , providing 12 mm thick cement plaster ( 1:3 ) with clean coarse sand of f.m 1.5with 1.5 mm thick ceme punning over it including screenig, curing, wit all leads and lifts of as per building specification and direction of e / i. , providing and supplying blue mdpe pipes confirming to iso 4427:1996 manufactured from vrgin resin pe 80 food grade compounded raw materials having blue colour only assurance certificate from quality agencies lke wrc / cipet ( india ) / dvm / kwa / spgn etc for usage in drinking water with quality system. this cost shall include testing of all materials all taxes central, state, municipal, inspection charges transportation up to site, transit insurance, loading, unloading, stacking etc complete as specified and directed. pn16 ( sdr 9 ) with ed ( 20mm ) , providing and supplying g.i. pipes ( tata and equivalent make ) for usage in drinking water with quality system. the cost shall include testing of al materials all taxes central state, municipal , inspection charges transportation up to site, transit insurance, loading, unloading, stacking etc complete as specified and directed. ( 15mm ) , lowering laying and jointinghdpe / mdpe pipes in proper position including all specials by compression fitting / electrofusion and but fusion jointing procedure including hydroulic testing as per relevent is code complete with all materials for jointing procedures like electrofusion c30machine, electric mirror / heater / but fusion welding machine with hydraulic jack, top loading clamp etc. pump and accessories fro hydraulic testing and all labours as direted by e / i as per is 7634 part 2 ( 20mm ) , supplying labours and tools fro fixing g.i. pipes with red lead and yarn of following nominal bore with screwed and socketed joints on wall, celling and floor including supplying and fittings of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if required etc. all complete as per specification and direction of e / i. , supplying and fixing of g.m. ferrule of approved make in existing c.i / d.i. main including drilling and taping c.i. / d.i. main all complete as per specification and direction of e / i ( 3mm dia ) , providing and fixing of g.m. fullway valve of approved quality all complete as per specification and direction of e / i ( 20mm dia ) , providing and fixing of male ended c.i. body brass spindle valve and seat bib cock of approved quality with extra socket all complete as per specification and direction of e / i ( 20 mm dia ) , supplying and fixing g.i. fitting of approved make all complete as per specification and direction of e / i , 20mm dia elbow , 15mm dia elbow , 20mm dia reducing socket , 20 mm dia nipple , 15 mm dia nipple , 20mm dia union socket , 15mm dia socket , 20mm dia socket , carriages of materials , ( b ) sand 36 km lead , ( c ) stone chips 11 km lead , ( d ) cement 10 km lead , operation & maintenance for five years ( excludingenergy charge ) , o / m work with labour component & materials for 1st year , as per sbd section 5 clouse 9.10 , o / m work with labour component & materials for 2nd year , as per sbd section 5 clouse 9.10 , o / m work with labour component & materials for 3rd year , as per sbd section 5 clouse 9.10 , o / m work with labour component & materials for 4th year , as per sbd section 5 clouse 9.10 , o / m work with labour component & materials for 5th year , as per sbd section 5 clouse 9.10 , add @ 6% cgst , add @ 6% sgst , add @ 1% labour cess...

Directorate Of Employment And Training - Jharkhand

31243649 bids are invited for portable drill , wattmeter multirange , diagonal cutter ,service oscillator , welding table , ring spanner , scissor,gasket , pipe tube bender , spanner double , lapping plate, stop watch , refrigerant , heating kit with , tachometerdigital , micron vacuum , fin straightenedfin , filler gauge ,dial thermometer , compressors testers , digitalthermometer , instrumentation , cylinder 134 a , portableair lpc brazing , refrigerator 165l carrying , frost freerefrigerator , threefour door refrige , two stage rotaryvacuum , air compressor, two , reciprocating compressor ,dry n2 in cylinder , window a c 1 ton , duct able split ,recovery unit , cassette air conditioner , de scaling pumpset , fan coil unit , shell and tube , circulating water ,rotary hermetic , screw compressor , bottle cooler , deepfreezer , water cooler , ice candy plant , airconditioning ,package ac , car a c componentsfull , car ac tutorial ,chart stand , plumb bob , small crimping , conduit pipe ,conduit pipe bending , crimping tool , rule four fold wood ,set of wall , hot wire ammeter , voltmeter centre zero ,field regulator , watt meter , personal computer , singlephasing preventer , transformer single phase , ss and sccentre , radial drill , universal milling machine , cnc lathecnc turn centre , lcd projector , cylindrical external ,lapping machine , scroll compressor , air compressor , airconditioning , four stroke petrol engine , tube tyre , twopost car lift , tyre changer machine , wheel alignmen ,working condition , moulding machine , core oven ,induction furnace cap , pigeon hole cabinet , printer table ,storage cabinet , steel almirah , soft board for iti equipments total quantity : 805...

South Eastern Railways - Jharkhand

31180545 supply of 2 hp submersible pump, single phase with dol2 hp submersible pump, single phase with dol,2 hp submersible pump, single phase with dol starter with ammeter, voltmeter and single phase protection relay, 214 247 mtr head, discharge:0.5 0.9 m3/hrs, discharge pipe dia 32 mm. make kirloskar, cri, ksb or similar as per attached details specification....

South Eastern Railways - Jharkhand

31064008 supply of 2 hp submersible pump, single phase with dol2 hp submersible pump, single phase with dol,2 hp submersible pump, single phase with dol starter with ammeter, voltmeter and single phase protection relay, 214 247 mtr head, discharge:0.5 0.9 m3/hrs, discharge pipe dia 32 mm. make kirloskar, cri, ksb or similar as per attached details specification....

Drinking Water And Sanitation Department - Jharkhand

31001818 supplying, installation, testing and commissioning submersible pump set for rural water supply scheme manushmudya, pumping plant. under d.w & s mechanical division, jamshedpur 1 supply of submersible pump set suitable for 6 dia bore well running with 3 phase415± 10% volts50 c / s 2900 rpm having discharging capacity 2600 gph against total head of 60 meters with noryl / g.m impeller consists of following accessories ( a ) 2½ dia g.i column pipe 200 ( 10 long both end threaded one end fitted socket and other end covered by plastic ) ( b ) 3 core flat copper cable 4 mm² 1 coil ( c ) m.s clamp 2½ dia 2 pairs ( d ) c.i.d.f sluice valve 2½dia 1no. ( e ) ) c.i.d.freflexvalve 2½dia 1no. 2 supplying and fitting cubical type duly painted control panel boardconsisting 32 amps. tpn mccb inbuilt single phase preventor and suitable forstar delta automatic starter water level guard with suitable length and size of wire phase indicating bulb in three different colour suitable voltmeter and ampere meterwith selector switch make l&t / havell;s 3 chemical earthing3 metersand80 mm hole size with electrode and chemical compound etc. with watering pipe and locking arrangement including soldering, riveting, jointing g.i flat 50 mm x 6 mm to all equipments. 4 supplyingtriple spur gear type 3 tonne capacitychain pulley block suitable for capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per is 3832 carrying isi mark. 5 renovation of light wiring inside & out side pump chamber by doing short point light wiring 4 point long point light wiring 4 points, 150 watt led street light complete set 2 nos., 36 watt cfl 4 nos. etc. all including labour charges all complete 6 supplying and making tripod ( 14x 65 mm c.i pipe ) hanging chain pulley block 7 supplyingxlpe / pvc insulated, armoured cable 1100 v grade with isi mark 25 mm² x 3½ core, solid / stranded copper conductor with 6 mm thick 25 mm width m.s. spacer with g.i. earth wire 6 sq mm, completein an approved. from transformer to p / house via gangway. 8 supplying installation testing and commissioning of 30 kva servo controlled automatic voltage stabilizer oil cooled power line / ipc / servokon make suitable for output voltage of 415 volt ± 1% under input voltage range of 280 450 volts ( phase to phase ) 3 phase, 50 hz, with copper wound transformer. the stabilizer shall function satisfactory even if incoming supply is unbalanced between phases within range of 10%. the stabilizer should have indicator, alarm, voltmeterand auto / manual selector switch for measuring input and output voltage, raise / low push buttons etc. suitable capacity terminationstrip and bus bars for incoming and outgoing cable should be provided. all three phase shall be independently monitored and corrected. following protections and indications shall be incorporated :over voltage / under voltage single phasing cut off conductor with electronic output sensing unit. 9 supplying and fixing 100 amp. 415± 15% voltage change over switch, havells / l & t make 10 transformer oil for the above stabilizer of best make up to mark. 11 supplying, installation, testing & commissioningof outdoor type 63 kva 11 / 0.433 kva copper wound distribution transformer with off load tap changer 12.5% to 2.5% in step of 2.5%, continuously rated for three phase, 50 hz, full load and temperature rise not exceeding 45 degree centigrade by thermometer in oil and 50 degree centigrade by the resistance in winding after continuous, run atfull load rating, the transformer should have oil immersed winding having vector group of 0.4 / 11, ht side connected in delta & lt side connected in star with neutral brought out connected. the transformer should have power terminal bushing arrangement on ht side & cable box in lt side with standard fitting for mounting of transformer with first filling of transformer oil including all accessories etc. all complete with all materials make – indian transformer / synergy / banglabijulee / kirloskar for ruralwatersupply p / pmanushmudia....

South Eastern Railways - Jharkhand

30874643 supply of voltmeter o 800 v ac 1.5. size 72 sq.mm ( square type) make ae or similar. accepted make as per bom of rdso spec. no. rdso/pe/spec/ac/0184 2015 (rev 0) ae/mullerzeigler/rishabh/lt/yokins.voltmeter o 800 v ac 1.5. size 72 sq.mm ( square type) make ae or similar. accepted make as per bom of rdso spec. no. rdso/pe/spec/ac/0184 2015 (rev 0) ae/mullerzeigler/rishabh/lt/yokins.,voltmeter o 800 v ac 1.5. size 72 sq.mm ( square type) make ae or similar. accepted make as per bom of rdso spec. no. rdso/pe/spec/ac/0184 2015 (rev 0) ae/muller+zeigler/rishabh/l&t/yokins....

Drinking Water And Sanitation Department - Jharkhand

30349803 e quotation for seeking firm rates of non schedule items for preparing estimates for renovation of e and m items of namkum rural water supply scheme. e quotation for seeking firm rates of non schedule items for preparing estimates for renovation of e and m items of namkum rural water supply scheme. , raw water pumping plant supplying, installation, testing and commissioning of vertical turbine pump set with ss impeller capable of discharge 126 m³ per hour against total head of 50m. with heavy duty m.s column assembly with ss line shaft approx. 20 feet long and each column of 5 feet length [ make kirloskar / jyoti / wilo mather & platt / wpil ] coupled with suitable capacity vertical hollow shaft / solid shaft squirrel cage induction motor of [ make kirloskar / cgl / abb / siemens ] operated on 415±10% volt, 3 phase, 50 c / s, a.c supply, ie3 type as per is: 325 and iec: 63400 1 having speed 1450 rpm including cost of supplying fitting and fixing of all required accessories such as dldf sluice valve 2 set, didf nr valve 1 set, pressure gauge, strainer, m.s. channel base plate etc. all complete including cost of dismantling of existing pump sets. , supplying & installation of fasd starter suitable for above vhs – sci motors ( make l&t / bch / siemens / schneider ) . , supplying and laying of 25 mm², 1.1 kv, 3core pvc insulated and pvc sheathed copper armoured cable conforming to is:1554 / ii [ make polycab / kei / v guard / havells ] from starter to motor. [ 2x ( 8+10 ) ] =36 , cost towards supplying and fitting 200 amp 4 pole main switch offload type with side handle [ make l&t / bch / siemens ] , cost towards light wiring of pump house including supplying and fitting 2 nos. t / light set, 2 nos. 30 watt led light luminaries complete set – 1 no etc. all complete. , cost towards dismantling of old damaged and rusted ms flooring and making new ms sheet floor over intake well of diameter 19 feet by supplying all labour, tools and tackles, welding rods and machine at site by supplying, fitting & fixing of chequered ms plate quantity: 6 nos. of ( 4x16 ) ms plate weight of each 4 x 16 x 5mm ms plate= 265 kg total weight required = 6x265 = 1590 kg total cost @rs.87.0 per kg = 1590x87 = rs. 138330.00 deduction for scrap: 400 kg ( approx. ) @ 32 = ( ) rs. 12800.00 rs. 125530.00 cost of cutting, welding, fixing and transportation =rs. 30000.00 rs. 155530.00 , supplying and fitting 5 ton capacity triple spur gear type chain pulley block suitable for capacity with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per is 3832 carrying isi mark. , cost towards supplying, fitting and fixing of new window size ( 4x3 ) steel structure iron sheet door with steel grill. taking down old window including taking stacking serviceable material disposal of unserviceable material with all lead all complete including 2 coat painting as per direction of e / i. , clear waterpumping plant supplying, installation, testing and commissioning of horizontal split case centrifugal pump set with bronze impeller capable of discharge 126 m³ / h against total head of 35m. [ make kirloskar / jyoti / wilo mather & platt / wpil ] and mounted on a common ms base plate with coupling and coupled with squirrel cage induction motor [ make kirloskar / cgl / abb / siemens ] tefc, ie3 type as per is:325 and iec: 63400 1 operated on 415 volt ± 10%, 3 phase, 50 hz. a.c supply, 1500 rpm including cost of supplying, fitting and fixing of all required accessories such as cidf sluice valve 2 sets, cidf nr valve 1 set, foot valve 1set etc. all complete including cost of dismantling of existing foundation and making new foundation , fixing and aligning base plate. , dismantling of old pcc foundation and making new pcc foundation including the cost of stone chips, sand, cement, foundation nut bolt spring, washer, plastering, punning and curing of foundation etc. all complete as per required shape & size with all other required accessories. , supplying & installation of fasd starter suitable for the above sci motors make l&t / bch / siemens / schneider. , cost towards supplying and laying 16 mm² x 3 core copper cable [ make polycab / kei / v guard / havells ] from panel to starter and starter to motor in bunch of two. ( both sets ) . 10x2x2=40 m. , renovation of light wiring inside and outside p / plant by doing short point light wiring 2 points, long points 2 points, 20 w led light 2 nos., 30 w led street light 2 no. including labour charge & cost of copper wire, pvc tape, pvc pipe, bend & other materials all complete. , cost towards supplying and fitting 200 amp 4 pole main switch offload type with side handle. [ make l&t / bch / siemens ] , submersible p / set supply and installation of submersible pump set cost towards supplying and installation of three phase submersible pump set 415+_15% running at 2900 rpmhaving discharge capacity of 2500 to 3500 lph against a total head of80 to120 meters [ make ksb / kirloskar / falcon ] including all accessories such as : 32 mm dia pvc heavy duty pipe 80 meters ( ii ) 4.0 sq. mm x 3 core flat copper cable 120 meters up to the panel board ( iii ) g.m gate valve 1 no. , g.m. reflex valve 1 no. on delivery pipe line 50 mm pvc pipe 40 m including with laying all fittings bend nipple t for jointing to overhead tankhaving suitable panel board having suitable starter, main switch pilot lamp, voltmeter, ampere meter, including ½” diarope for lifting and 2 pair ms clamp etc. all complete. including digging earth and laying cable under 1.5” dia black pvc pipe for protection as per direction of e / i....

East Central Railway - Jharkhand

30313675 supply of three phase variac 0 480 v acthree phase variac 0 480 v ac,three phase variac 0 480 v ac, 115 150a(three phase variable supply)3 phase 4 wire with digital voltmeter & ammeter for showing the load 0 440v variable power supply enclosed type manual or motor operated suitable for testing 60kva three phase transformer & other electrical equipment oil cooled suitable for floor mounting => limited...

East Central Railway - Jharkhand

30266928 supply of battery voltmeterbattery voltmeter,battery voltmeter(uba),range:0 150v, specification: clw/es/3/0073 and drg. no. clw/es/3/sk 1/0073 range 0 150 volts...

East Central Railway - Jharkhand

30009426 supply of battery voltmeterbattery voltmeter,battery voltmeter(uba),range:0 150v, specification: clw/es/3/0073 and drg. no. clw/es/3/sk 1/0073 range 0 150 volts...

Central Organisation Railway Electrification - Jharkhand

29998351 supply of supply & commissioning outdoor type l t panel.supply & commissioning outdoor type l t panel.,supply & commissioning outdoor type lt panel consisting of the following: (a) mccb 200a 250a 4pole 25ka with spreader terminal & under voltage release : 02 nos. (b) mccb 80a 100a 4 pole 25ka withspreader terminal & under voltage release : 03 nos. (c) mccb 50a 63a 4 pole 25ka with spreader terminal &under voltage release : 02 nos. (d) digital ammeter 96sq mm : 02 nos. (e) digital voltmeter 96sq mm : 02 nos. (f)mcb sp 6a : 06 nos. (g) ct 200/15a 15va (cl 1) : 06 nos. (h) led indication lamp : 06 nos (r 2, y 2, b 2).mccb make l&t or similar....

Central Organisation Railway Electrification - Jharkhand

29998227 supply of supply & commissioning of indoor type lt panel.supply & commissioning of indoor type lt panel.,supply & commissioning of indoor type lt panel consisting of the following: (a) mccb 320a 400a,4 pole 36ka with spreader terminal & under voltage release : 02 nos. (b) mccb 200a 250a 4 pole with spreaderterminal & under voltage release : 04 nos. (c) mccb 80a 100a 4 pole 25ka with spreader terminal & undervoltage release : 03 nos. (d) mccb 50a 63a 4 pole 25ka with spreader terminal & under voltage release : 02nos. (e) digital ammeter 96sq mm : 02 nos. (f) digital voltmeter 96sq mm : 02 nos. (g) mcb sp 6a : 06 nos. (h)ct 400/5a 15va (cl 1) : 06 nos. (i) led indication lamp : 06 nos (r 2, y 2, b 2). mccb make l&t or similar.sse/re/rnc ( bapi ghosh) , jharkhand 1.00 set...

Department Of Technical Education - Jharkhand

29883300 bids are invited for measuring steel tape_ measuring steel tape 5 meter , combination plier_ combination plier insulated 200 mm , screw driver insulated_ screw driver insulated 4mm x 150 mm, diamond head , screw driver insulated_1 screw driver insulated 6mm x 150 mm , electrician screw driver_1 electrician screw driver thin stem insulated handle 4mm x 100 mm , heavy duty screw driver_2 heavy duty screw driver insulated 5mm x 200 mm , electrician screw driver_3 electrician screw driver thin stem insulated handle 4mm x 250 mm , punch centre_ punch centre 4mm x 250 mm , knife double bladed_ knife double bladed electrician 100 mm , neon tester_ neon tester 500 v , steel rule graduated_ steel rule graduated both in metric and english unit 300 mm with precision of 1/4th mm , hammer_ hammer, cross peen with handle 250 grams , electrical symbol and accessories charts_ electrical symbol and accessories charts , pipe vice cast iron with hardened jaw_ pipe vice cast iron with hardenedjaw open type 100 mm , hand vice_ hand vice 50 mm jaw , table vice_ table vice – 100 mm jaw , hacksaw frame_ hacksaw frame (with blade) adjustable 300 mm ,fixed 150 mm , file flat_ file flat 200 mm 2nd cut with handle , file half round_ file half round 200 mm 2nd cut with handle , file round_ file round 200 mm 2nd cut with handle , pliers long nose_ pliers long nose insulated 150 mm , pliers flat nose_ pliers flat nose insulated 200 mm , pliers, round nose_ pliers, round se insulated 100 mm , d_e_ metric spanner_ d.e. metric spanner double ended 6 32 mm , gauge, wire imperial stainlees steel marked_ gauge, wire imperial stainlees steel marked in swg & mm wire gauge metric , portable electric drill machine_ portable electric drill machine 12 mm capacity 750w, 240v with chuck and key , crimping tool _ crimping tool 1.5 sq mm to 16 sq mm, 16 sq mm to 95 sq mm , pliers side cutting_ pliers side cutting 150 mm , wire stripper adjustable length_ wire stripper adjustable length , hammer, ball peen with handle_ hammer, ball peen with handle , scriber_ scriber (knurled centre position ) , tool kit box/bag portable_ tool kit box/bag portable , allen key_ allen key , scissors blade_ scissors blade 150 mm , electrical loads_ electrical loads:of incandescent lamp, tube light, cfl, led light, heater and geyser , torque wrench_ torque wrench 8n m to 15n m , pipe cutter to cut pipes_1 pipe cutter to cut pipes 8n m to 15n m , pipe cutter to cut pipes_2 pipe cutter to cut pipes above 5 cm dia , try square_ try square above 5 cm dia , load bank_ load bank , wire cutter and stripper_ wire cutter and stripper 150 mm , earth plate_ earth plate,60cm x 60cm x 3.15mm copper plate,60cm x 60cm x 6mm gi plate , earth electrode_ earth electrodeprimary electrode 2100x28x3.25mm secondary cu strip 20x5mm , out side micrometer _ out side micrometer 0 25 mm least count 0.01mm , tap_ tap different size , trolley for transportation_ trolley for transportation of batteries , die for threading_ die for threading different sizes , rooftop mounting structure_ rooftop mounting structure for 4 x 250 w solar panels mounting practice, with tilt adjustment , electrical wiring and switch gear rack_ electrical wiring and switch gear rack electrical control elements suitable for practice of control circuits using banana plugs and sockets , protective relays and contactors rack_ protective relays and contactors rack suitable for practice of control circuits using banana plugs and sockets , mcb training up_ mcb training up training up should represents many essential safety precautions. it should provide real time appearance of mcb to help the students to understand its mechanical , elcb and rccb_ elcb and rccb 25amps, double pole and 25amps, double pole, i?n 30 ma , fuses training up_ fuses training up training up should represents many essential safety precautions. it should provide real time appearance of fuse to help the students to understand in very easy way, it , cables: 1 mtr_ cables: 1 mtr each , solar cable (red)_ solar cable (red) 5 square mm , solar cable (black)_ solar cable (black) 5 square mm , three core wire_ three core wire (230 v, 15 a) , battery cable_ battery cable (230 v, 15 a) , resin cored solder_ resin cored solder , solder wax_ solder wax , mc – 4 connector set_ mc – 4 connector set of 5 pairs , pins_ pins 5 mm , lugs_ lugs 7.5 mm , hacksaw blades_ hacksaw blades 200 mm, 300 mm , bolts, nuts, anchor bolts, washers, screws, other pins, lugs etc_ bolts, nuts, anchor bolts, washers, screws, other pins, lugs etc , civil work utensils spade, mixing spoon, leveling plates_ civil work utensils spade, mixing spoon, leveling plates , plumbing tools_ plumbing tools , plumbing raw materials_ plumbing raw materials , civil work raw materials_ civil work raw materials , 3 ¾ digit digital multimeter_1 3 ¾ digit digital multimeter , megger analog 500 v_ megger analog 500 v , hydrometer_ hydrometer , solar insulation meter_ solar insulation meter , pyrameter_ pyrameter , lux meter_ lux meter , magnetic flux meter_ magnetic flux meter , tong tester/ clamp meter_ tong tester/ clamp meter , soldering station with necessary_accessories soldering station with necessary accessories , smd soldering & de soldering station_ smd soldering & de soldering station with necessary accessories , thermometer digital_ thermometer digital 0° c 150° c , sun shine recorder with leveling base_ sun shine recorder with leveling base and one year chart complete , weather monitoring system_ weather monitoring system , solar cell based sunshine radiation meter_ solar cell based sunshine radiation meter , magnetic compass_ magnetic compass , cut models of photo voltaic cell assembly__ cut models of photo voltaic cell assembly. , lead acid battery cut model demonstration of construction of internal parts of a 12 volt 7.5a smf battery , lead acid battery_1 lead acid battery 12v, 40ah, 75ah , lead acid battery_2 lead acid battery 12v, 100 ah , solar simulator for solar cell characteristic study_ solar simulator for solar cell characteristic study , solar pv module analyzer_ solar pv module analyzer , sun path finder_ sun path finder , solar energy trainer_ solar energy trainer with grouping of solar cells , solar tracker demonstrator kit_ solar tracker demonstrator kit , solar pv learning software_ solar pv learning software using animations for training (5 user) , halogen lamp_ halogen lamp with stand for illumination of solar panels in lab , motorized bench grinder_ motorized bench grinder : ac mains operated , battery charger_ battery charger , solar photovoltaic module_ solar photovoltaic module , solar panels : 350 watt poly crystalline_ solar panels : 350 watt poly crystalline , solar charge controller with dusk to dawn automatic switching_ solar charge controller with dusk to dawn automatic switching , solar charge controller with manual switch ( day lighting)_ solar charge controller with manual switch ( day lighting) , array junction box_ array junction box , solar lantern (led type)_ solar lantern (led type) , solar lantern assembly_ solar lantern assembly , home light system_ home light system , solar cell kit_ solar cell kit , clinometer : for angle measurement_ climeter : for angle measurement , spirit level : for floor level check_ spirit level : for floor level check , anemometer : for wind speed measurement_ anemometer : for wind speed measurement , dc table fan – 12v_ dc table fan – 12v , a_c_ voltmeter m_i : 0 –500v ac_ a.c. voltmeter m.i : 0 –500v ac , volt meter : 0 30v_ volt meter : 0 30v , volt meter : 0 100v_ volt meter : 0 100v , ammeter mc_ ammeter mc : 0 1a abs moulded dust proof cases with zero adjuster accessible from the front. range: current(a): 0 1a..accuracy: ±1.5% of full scale. , ammeter mc : 0 5a_ ammeter mc : 0 5a , ammeter mc centre zero : 0 20a_ ammeter mc centre zero : 0 20a , ammeter mc centre zero: 0 50a_ ammeter mc centre zero: 0 50a , power factor meter_ power factor meter , rheostats various values and ratings_ 0 1 ohm, 5 amp, 0 10 ohm, 5 amp,0 25 ohm, 1 amp,0 300 ohm, 1 amp , a_c_ energy meter single phase_ a.c. energy meter single phase, 10 a, 240 v induction type , a_c_ energy meter_ a.c. energy meter , kilo wattmeter analog_ kilowattmeter analog 0 1.5 3kw, pressure coil rating 240v/440v, current rating 5a/10a analog, portable type housed in bakelite case , digital wattmeter_ digital wattmeter , phase sequence indicator_ phase sequence indicator , frequency meter_ frequency meter : 45 to 55 hz , dc led lamp_ dc led lamp : 3w, 5w, 10w , dc pump – 24v _ solar water pump demonstrator dc pump – 24v , pwm charge controller training system_ pwm charge controller training system , mppt charge controller_ mppt charge controller , inverter with battery_ inverter with battery , solar pcu_ solar pcu , on grid solar power generation and training system_ on grid solar power generation and training system , smart solar street lighting training platform_ smart solar street lighting training platform , solar wind hybrid power plant_ solar wind hybrid power plant , solar street light_ solarstreet light (solartraffic light) , exploring waste water treatment by electro coagulation_ exploring waste water treatment by electro coagulation , solar dc pump 1 hp_ solar dc pump 1 hp , demonstration kit for wind generation_ demonstration kit for wind generation (wind turbine with blower/fan ) , rechargable battery_1 rechargable battery 12v,100ah , rechargable battery_2 rechargable battery 12v,7ah , rechargable battery_3 rechargable battery 5v,6ah , led lights_3 led lights 12 v dc , led lights_4 led lights 6v dc , rubber gloves_ rubber gloves , cotton gloves_ cotton gloves , gum boots_ gum boots , safety goggles_ safety goggles , safety helmet_ safety helmet , first aid kit_ first aid kit , fire extinguisher_ fire extinguisher co2 : 2 kg , fire buckets_ fire buckets , working bench_ working bench 2.5 m x 1.20 m x 0.75 m , wiring board_ wiring board 2.5 m x 1.20 m x 0.75 m , instructors table_1 instructor’s table , instructors chair_2 instructor’s chair , trainee tables_ trainee tables (for 2 trainees) , trainee chairs_ trainee chairs , metal rack_ metal rack , lockers_ lockers with 16 drawers standard size , steel almirah_ steelalmirah , white board_ white board 1200mm x 900mm , lcd projector_ lcd projector , computer_ computer (pc) with latest configurations and internet connection with standard operating system and standard word processor and worksheet software , ups : 600 va_ ups: 600 va , lan connection_1 lan connection for lab.. , training _1 training of trainers for 180 days.. , scanner cum printer_ scanner cum printer , laser jet printer_ laser jet printer , measuring steel tape measuring steel tape 5 meter , combination plier combination plier insulated 200 mm , screw driver insulated_3 screw driver insulated 4mm x 150 mm, diamond head , screw driver insulated_4 screw driver insulated 6mm x 150 mm , electrician screw driver_4 electrician screw driver thin stem insulated handle 4mm x 100 mm , heavy duty screw driver_5 heavy duty screw driver insulated 5mm x 200 mm , electrician screw driver_6 electrician screw driver thin stem insulated handle 4mm x 250 mm , punch centre punch centre 4mm x 250 mm , knife double bladed knife double bladed electrician 100 mm , neon tester neon tester 500 v , steel rule graduated steel rule graduated both in metric and english unit 300 mm with precision of 1/4th mm , hammer hammer, cross peen with handle 250 grams , electrical symbol and accessories charts electrical symbol and accessories charts , pipe vice cast iron with hardened jaw pipe vice cast iron with hardenedjaw open type 100 mm , hand vice hand vice 50 mm jaw , table vice table vice – 100 mm jaw , hacksaw frame hacksaw frame (with blade) adjustable 300 mm ,fixed 150 mm , file flat file flat 200 mm 2nd cut with handle , file half round file half round 200 mm 2nd cut with handle , file round file round 200 mm 2nd cut with handle , pliers long nose pliers long nose insulated 150 mm , pliers flat nose pliers flat nose insulated 200 mm , pliers, round nose pliers, round se insulated 100 mm , d.e. metric spanner d.e. metric spanner double ended 6 32 mm , gauge, wire imperial stainlees steel marked gauge, wire imperial stainlees steel marked in swg & mm wire gauge metric , portable electric drill machine portable electric drill machine 12 mm capacity 750w, 240v with chuck and key , crimping tool crimping tool 1.5 sq mm to 16 sq mm, 16 sq mm to 95 sq mm , pliers side cutting pliers side cutting 150 mm , wire stripper adjustable length wire stripper adjustable length , hammer, ball peen with handle hammer, ball peen with handle , scriber scriber (knurled centre position ) , tool kit box/bag portable tool kit box/bag portable , allen key allen key , scissors blade scissors blade 150 mm , electrical loads electrical loads:of incandescent lamp, tube light, cfl, led light, heater and geyser , torque wrench torque wrench 8n m to 15n m , pipe cutter to cut pipes_3 pipe cutter to cut pipes 8n m to 15n m , pipe cutter to cut pipes_4 pipe cutter to cut pipes above 5 cm dia , try square try square above 5 cm dia , load bank load bank , wire cutter and stripper wire cutter and stripper 150 mm , earth plate earth plate,60cm x 60cm x 3.15mm copper plate,60cm x 60cm x 6mm gi plate , earth electrode earth electrodeprimary electrode 2100x28x3.25mm secondary cu strip 20x5mm , out side micrometer out side micrometer 0 25 mm least count 0.01mm , tap tap different size , trolley for transportation trolley for transportation of batteries , die for threading die for threading different sizes , rooftop mounting structure rooftop mounting structure for 4 x 250 w solar panels mounting practice, with tilt adjustment , electrical wiring and switch gear rack electrical wiring and switch gear rack electrical control elements suitable for practice of control circuits using banana plugs and sockets , protective relays and contactors rack protective relays and contactors rack suitable for practice of control circuits using banana plugs and sockets , mcb training up mcb training up training up should represents many essential safety precautions. it should provide real time appearance of mcb to help the students to understand its mechanical , elcb and rccb elcb and rccb 25amps, double pole and 25amps, double pole, i?n 30 ma , fuses training up fuses training up training up should represents many essential safety precautions. it should provide real time appearance of fuse to help the students to understand in very easy way, it , cables: 1 mtr cables: 1 mtr each , solar cable (red) solar cable (red) 5 square mm , solar cable (black) solar cable (black) 5 square mm , three core wire three core wire (230 v, 15 a) , battery cable battery cable (230 v, 15 a) , resin cored solder resin cored solder , solder wax solder wax , mc – 4 connector set mc – 4 connector set of 5 pairs , pins pins 5 mm , lugs lugs 7.5 mm , hacksaw blades hacksaw blades 200 mm, 300 mm , bolts, nuts, anchor bolts, washers, screws, other pins, lugs etc bolts, nuts, anchor bolts, washers, screws, other pins, lugs etc , civil work utensils spade, mixing spoon, leveling plates civil work utensils spade, mixing spoon, leveling plates , plumbing tools plumbing tools , plumbing raw materials plumbing raw materials , civil work raw materials civil work raw materials , 3 ¾ digit digital multimeter_2 3 ¾ digit digital multimeter , megger analog 500 v megger analog 500 v , hydrometer hydrometer , solar insulation meter solar insulation meter , pyrameter pyrameter , lux meter lux meter , magnetic flux meter magnetic flux meter , tong tester/ clamp meter tong tester/ clamp meter , soldering station with necessary accessories soldering station with necessary accessories , smd soldering & de soldering station smd soldering & de soldering station with necessary accessories , thermometer digital thermometer digital 0° c 150° c , sun shine recorder with leveling base sun shine recorder with leveling base and one year chart complete , weather monitoring system weather monitoring system , solar cell based sunshine radiation meter solar cell based sunshine radiation meter , magnetic compass magnetic compass , cut models of photo voltaic cell assembly. cut models of photo voltaic cell assembly. , lead acid battery cut model_ demonstration of construction of internal parts of a 12 volt 7.5a smf battery , lead acid battery_3 lead acid battery 12v, 40ah, 75ah , lead acid battery_4 lead acid battery 12v, 100 ah , solar simulator for solar cell characteristic study solar simulator for solar cell characteristic study , solar pv module analyzer solar pv module analyzer , sun path finder sun path finder , solar energy trainer solar energy trainer with grouping of solar cells , solar tracker demonstrator kit solar tracker demonstrator kit , solar pv learning software solar pv learning software using animations for training (5 user) , halogen lamp halogen lamp with stand for illumination of solar panels in lab , motorized bench grinder motorized bench grinder : ac mains operated , battery charger battery charger , solar photovoltaic module solar photovoltaic module , solar panels : 350 watt poly crystalline solar panels : 350 watt poly crystalline , solar charge controller with dusk to dawn automatic switching solar charge controller with dusk to dawn automatic switching , solar charge controller with manual switch ( day lighting) solar charge controller with manual switch ( day lighting) , array junction box array junction box , solar lantern (led type) solar lantern (led type) , solar lantern assembly solar lantern assembly , home light system home light system , solar cell kit solar cell kit , clinometer : for angle measurement climeter : for angle measurement , spirit level : for floor level check spirit level : for floor level check , anemometer : for wind speed measurement anemometer : for wind speed measurement , dc table fan – 12v dc table fan – 12v , a.c. voltmeter m.i : 0 –500v ac a.c. voltmeter m.i : 0 –500v ac , volt meter : 0 30v volt meter : 0 30v , volt meter : 0 100v volt meter : 0 100v , ammeter mc ammeter mc : 0 1a abs moulded dust proof cases with zero adjuster accessible from the front. range: current(a): 0 1a..accuracy: ±1.5% of full scale. , ammeter mc : 0 5a ammeter mc : 0 5a , ammeter mc centre zero : 0 20a ammeter mc centre zero : 0 20a , ammeter mc centre zero: 0 50a ammeter mc centre zero: 0 50a , power factor meter power factor meter , rheostats various values and ratings 0 1 ohm, 5 amp, 0 10 ohm, 5 amp,0 25 ohm, 1 amp,0 300 ohm, 1 amp. , a.c. energy meter single phase a.c. energy meter single phase, 10 a, 240 v induction type , a.c. energy meter a.c. energy meter , kilo wattmeter analog kilowattmeter analog 0 1.5 3kw, pressure coil rating 240v/440v, current rating 5a/10a analog, portable type housed in bakelite case , digital wattmeter digital wattmeter , phase sequence indicator phase sequence indicator , frequency meter frequency meter : 45 to 55 hz , dc led lamp dc led lamp : 3w, 5w, 10w , dc pump – 24v solar water pump demonstrator dc pump – 24v , pwm charge controller training system pwm charge controller training system , mppt charge controller mppt charge controller , inverter with battery inverter with battery , solar pcu solar pcu , on grid solar power generation and training system on grid solar power generation and training system , smart solar street lighting training platform smart solar street lighting training platform , solar wind hybrid power plant solar wind hybrid power plant , solar street light solarstreet light (solartraffic light) , exploring waste water treatment by electro coagulation exploring waste water treatment by electro coagulation , solar dc pump 1 hp solar dc pump 1 hp , demonstration kit for wind generation demonstration kit for wind generation (wind turbine with blower/fan ) , rechargable battery_4 rechargable battery 12v,100ah , rechargable battery_5 rechargable battery 12v,7ah , rechargable battery_6 rechargable battery 5v,6ah , led lights_1 led lights 12 v dc , led lights_2 led lights 6v dc , rubber gloves rubber gloves , cotton gloves cotton gloves , gum boots gum boots , safety goggles safety goggles , safety helmet safety helmet , first aid kit first aid kit , fire extinguisher fire extinguisher co2 : 2 kg , fire buckets fire buckets , working bench working bench 2.5 m x 1.20 m x 0.75 m , wiring board wiring board 2.5 m x 1.20 m x 0.75 m , instructors table_3 instructor’s table , instructors chair_4 instructor’s chair , trainee tables trainee tables (for 2 trainees) , trainee chairs trainee chairs , metal rack metal rack , lockers lockers with 16 drawers standard size , steel almirah steelalmirah , white board white board 1200mm x 900mm , lcd projector lcd projector , computer computer (pc) with latest configurations and internet connection with standard operating system and standard word processor and worksheet software , ups : 600 va ups: 600 va , lan connection_ lan connection for lab.. , training _ training of trainers for 180 days.. , scanner cum printer scanner cum printer , laser jet printer laser jet printer total quantity : 1...

Bharat Heavy Electricals Limited - Jharkhand

29812611 fqa lab electrical for 3x800 mw pvunl patratu tpp phase i fqa lab electrical for 3x800 mw pvunl patratu tpp phase i , field quality laboratoryequipments , tachometer , tongtester ( ac ) 4000a , tongtester ( dc ) 4000a , wattmeter , ammeter ( tong tester ) , voltmeter , hv tester ( 0 100kv ) dc , resistance bridge: kelvin bridge , fault locator ( cable test kit ) , relay test kit , grounding device / earthing device , tan delta test kit , bdv tester for oil , spirit level , vibration meter , noise level meter , micrometer , vernier calliper , measuring tape , magnifying glass , ductor for trf. wdg, “r’’ , variable ac source ( 0 220v ) , variable dc source ( 0 220v ) , dead weight test ( accuracy class min 0.05% ) , pressure gauge ( accuracy class 0.25% ) , electro pneumatic calibrater ( accuracy 0.1% of full scale ) , fluidised temp bath ( 100 600 deg. c, stability + / 0.2% deg. c ) , thermocouple test furnace up to 1400 oc with uncertainty of 1 oc , barometer ( aneroid ) 660 to 800 mm / dg accuracy, + / 0.3% of full scale , mercury thermometer ( accuracy up to 0.1 deg c , manometer ( test & u tube ) , hygrometer , portable v. meter calibrator , resistance thermometer ( bridge 0 2000, resolution 0.001, accuracy + / 0.005, sensitivity 0.001%, amb. temp. 50 °c + / 0.005% of span per 1°c , rheostat ( rheostat 100 ohm, 5a + rheostat 1000 ohm, 1a ) , test ( reference ) rtd , digital storage oscilloscope , power pack 0 6 vdc current up to 10a, load regulation 0.01% , rcl meter ( for resistance, capacitance, inductance measurement ) accuracy 2% of fsd or better , ph simulator , portable tc thermo couple / rtd calibrator / simulator , function generator , portable high speed trend recorder , portable multifunction counter , non contact laser temperature gun ( up to 1000 oc , demonstration & handing over to bhel / bhels customer shall be as per annexure a to section ii of technical specification no. pe ts 434 571 e001 rev 01 / nit....

East Central Railway - Jharkhand

29722265 supply of battery voltmeter (uba),range:0 150v, specification/ drg.no. : clw specn. no. clw/es/3/0073 and drg. no. clw/es/3/sk 1/0073battery voltmeter (uba),range:0 150v, specification/ drg.no. : clw specn. no. clw/es/3/0073 and drg. no. clw/es/3/sk 1/0073,battery voltmeter (uba),range:0 150v, specification/ drg.no. : clw specn. no. clw/es/3/0073 and drg. no. clw/es/3/sk 1/0073...

East Central Railway - Jharkhand

29705246 supply of battery voltmeterbattery voltmeter,battery voltmeter(uba),range:0 150v, specification: clw/es/3/0073 and drg. no. clw/es/3/sk 1/0073 range 0 150 volts...

Drinking Water And Sanitation Department - Jharkhand

29167772 e quotation for seeking rates of materials for framing the estimates for supplying installation and commissioning of pump sets e quotation for seeking rates of materials for framing the estimates for supplying installation and commissioning of pump sets , raw water pumpimg plant supplying installation & commissioning of water lubricated single or multistage, radial / mixed flow vertical turbine pump having discharge 86m3 / hragainst a total head of 15m and depth 30 feet kirloskar / wpil / jyoti / mather & platt make with suitable size of column assembly ms fabricated, flanged line shaft with strainers, spider bearing, non reverse ratchet coupling and discharge head etc coupled with hollow / solid shaft, squirrel cage, ie3 energy efficient induction motor confirming to is 12615 :2011 with latest amendments operating on 415 v, 3 phase, 50hz, 1400 1500 rpm ( kirloskar, jyoti, abb, cgl, bhel orreputed make ) with suitable size of isi marked heavy duty cidf sluice valve, cidf nr valve, ms clamp etc all complete. , supplying installation and commissioning of motor control panel of free standing type floor mounted made of 2mm thick m.s. cubical panel should be duly painted with two coats of super enameled paint comprising of: ( a ) incoming feeder ( i ) 100a mccb 01 nos. ( ii ) 100 amp copper bus bar arrangement 4 pole ( iii ) phase indicating lamps ( b ) out going feeder ( i ) 63a mccb 3nos. ( ii ) voltmeter – 1nos. ( iii ) ammeter 1nos. ( iv ) selector switch ( v ) pilot lamps ( vi ) fasd starter 2 nos. ( 10hp ) including motor control relays, over / under current relays etc all complete internal wining with suitable size of copper wire. , supplying and laying of 10 mm2x 3 core pvc insulated and pvc sheathed unarmored copper conductor for power wiring from panel to motor for 02 sets. , supplying laying and fitting of 70mm2 x 3.5 core aluminium armoured cable universal / polycab / mescab or reputed make. , supplying and fitting of 100 amp change over switchl&t / havells / c&s or reputed make , supplying, installation and commissioning of 30 kva roller type servo stabilizer switch for input voltage 280 to 460 volts output voltage of 415+ 1% volt, 3 phase 50 hz with copper wound transformer ( oil cooled ) as mention below. the stabilizer shall function satisfactorily even if incoming supply is unbalanced between phase within range of 10% the stabilizer should be constructed in cubical box, with bidirectional wheels for easy handling, necessary monitors and user controls o9n front panel such as indicator alarm volt meter and selector switch for measuring input and output voltage, auto / manual selector switch, raise / low push button etc suitable capacity termination strips and bus bar for incoming and outgoing cable should be provided all three phase shall be independently monitored and connected following protections and indication shall be incorporated ( i ) over voltage / under voltage ( ii ) single phasing ( iii ) cut of contractor with electronic output sensing unit make servokon / powerline / powerstar / isi marked reputed make , supplying and erecting of earthing station as per ie rule including the cost of earth pit. 8 swg copper wire, g.i pipe all complete with sand, charcoal and salt etc to all electrical equipment in double way wire connection. , clear water pumpimg plant supplying installation & commissioning of hsc c / f pump single or multi stage pump set of kirloskar / jyoti / m&p / wpil make cable for discharging 36 m3 / hr against total head of 40 mtr. coupled with suitable size energy efficient ie3 induction motor as per is 12615:2011 with latest amendments induction motor three phase squirrel cage motor operated on 415volt 3phase, 50c / s, 1400 1500 rpm ( kirloskar, jyoti, abb, cgl, bhel orreputed make ) with suitable size of isi marked heavy duty cidf sluice valve, cidf nr valve etc all complete. , supplying installation and commissioning of motor control panel of free standing type floor mounted made of 2mm thick m.s. cubical panel should be duly painted with two coats of super enameled paint comprising of: ( a ) incoming feeder ( i ) 100a mccb 01 nos. ( ii ) 100 amp copper bus bar arrangement 4 pole ( iii ) phase indicating lamps. ( b ) out going feeder ( i ) 63a mccb 3nos. ( ii ) voltmeter 1nos. ( iii ) ammeter – 1nos. ( iv ) selector switch ( v ) pilot lamps ( vi ) fasd starter 2nos. ( 15hp ) including motor control relays, over / under current relays etc all complete internal wining with suitable size of copper wire. , supplying and laying of 16 mm2x 3 core pvc insulated and pvc sheathed unarmoured copper conductor for power wining from panel to motor for 02 sets. , supplying laying and fitting of 70mm2 x 3.5 core aluminium armoured cable universal / polycab / mescab or reputed make , supplying and fitting of 100 amp change over switchl&t / havells / c&s or reputed make , supplying, installation and commissioning of 50 kva roller type servo stabilizer switch for input voltage 280 to 460 volts output voltage of 415+ 1% volt, 3 phase 50 hz with copper wound transformer ( oil cooled ) as mention below. the stabilizer shall function satisfactorily even if incoming supply is unbalanced between phase within range of 10% the stabilizer should be constructed in cubical box, with bidirectional wheels for easy handling, necessary monitors and user controls o9n front panel such as indicator alarm volt meter and selector switch for measuring input and output voltage, auto / manual selector switch, raise / low push button etc suitable capacity termination strips and bus bar for incoming and outgoing cable should be provided all three phase shall be independently monitored and connected following protections and indication shall be incorporated ( i ) over voltage / under voltage ( ii ) single phasing ( iii ) cut of contractor with electronic output sensing unit make servokon / powerline / powerstar / isi marked reputed make , supplying and erecting of earthing station as per ie rule including the cost of earth pit. 8 swg copper wire, g.i pipe all complete with sand, charcoal and salt etc to all electrical equipment in double way wire connection....

Uranium Corporation Of India Limited - Jharkhand

28914325 supply of items 1 12 stage automatic power factor correction (apfc) relay with led/lcd display for programming and displaying parameters. voltage input 415v ac model no. etacon l12/ rvc 12/ equivalent ct sensing single phase input ct secondary 5a/1a (programmable) suitable for panel flush mounting size : 144 x 144 mm make : l&t/ abb/ siemens/ rishabh/ trinity/ automatic electric/ schneider/ meco 2 3 phase 415 volt digital type voltmeter with 3.5 digit bright led/lcd display i/p voltage measurement 50 520v ac (p p) auxillary voltage: 80 300v ac flush mounting size : 96 x 96 mm with inbuilt selector switch to show voltage in each phase, accuracy class 1.0, make : l&t/ abb/ rishabh/ trinity/ automatic electric/ schneider/ meco 3 3 phase 415 volt digital type ammeter with 3.5 digit bright led/lcd display auxillary voltage : 80 300v ac ct secondary selectable 1a/5a flush mounting size : 96 x 96 mm with inbuilt selector switch for showing current in each phase, accuracy class 1.0, make : l&t/ abb/ rishabh/ trinity/ automatic electric/ schneider/ meco ...

Building Construction Department - Jharkhand

28849171 quotations are invited through online for construction materials from reputed shop keepers, manufacturers, suppliers, retailers, distributors, timber merchants and others for following items 1 providing and fixing door shutter with wooden framed by 30mm thick both side best quality ply and veneer 4mm thick veneer of green décor make both side pasting finishing with melamine paint with all material and labour all complete ( including all fancy type fitting ) as per building specification and direction of e / i. 2 providing and fixing choukhat paneling with 12mm thick ply and 4 mm thick veneer both side pasting finishing with all material and labour all complete as per building specification and direction of e / i. 3 s / f / f all height wall paneling of 12mm thick water proof ply ( centure panic pine wood, isi mark, termites ) over 2x1 aluminum section, 4mm thick water proof veneer ( green dacore wood ) finishing with melamine polished all complete including all taxes and royalty all complete as per building specification and direction e / i 4 providing and laying machine cut, mirror polished italian marble stone flooring, in required design and in patterns in combination with italian marble stones of different colours, shades and finished surface texture of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 40 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with white cement slurry @ 4.4 kg / sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge 5 providing and applying plaster of patta paris over plastered surface to prepare the surface even and smooth complete. 6 supply fitting and fixing best quality wallpaper do complete job. 7 providing mellamine over new wooden surface to give desired texture and glossinculding wood filter with all labour and material all complete work as per instruction of e / i 8 providing and applying anti temite treatment wiyh all labour and material all complete work as per instruction of e / i 9 providing and laying app ( atactic polypropylene polymer ) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre / sqm by the same membrane manufacture of density at 25°c, 0.87 0.89 kg / litre and viscocity 70 160 cps. over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc, and preparing the surface complete. the vital physical and chemical parameters of the membrane shall be as under : joint strength in longitudinal and transverse direction at 23°c as 650 / 450n / 5cm. tear strength in longitudinal and transverse direction as 300 / 10 s / f / f cubical glass with dorma fitting as per direction e / i size 5 x 4 11 providing & fixing curtain of superior quality approved fabric material curtain & astar with rings , bukram , stiching charges making adequate plats fixing in prefixed curtain rod & power track as per direction of e / i curtain cloth make pure / dicitex / gmf 12 supply fitting & fixing shear all complete including all complete as per building specification and direction e / i 13 supply fitting & fixing bed. size ( 6.333 / 7.00 ) with 19 mm green plywith veneer and malamine polished including all complet job with nesesarry nail & hing.supply with head board sizd ( 8.75 / 4.00 ) with 19 mm green play , teak veneer, decorative type raxin steeching all complet job. 14 supply fitting& fixing side table size ( 1.33 / 1.33 ) with 19 mm green play drawer with veneer & malamine ploise all complet job. 15 supply fitting & fixing vip boss chair with teak wood frame with high quality leather, , with sleepwell foam do do all complete with malamine polish. 16 supply fitting fixing lunch / tea table size ( 29 x 1 2 x19 ) with 19 mm green play with veneer polished etc all complete job. 17 supply fitting fixing lcd cabint with matching to bed veneer polished etc all complete job. 18 supply fitting & fixing decorative type photo freaming with teak wood , desizne finished of size ( 43 x24 ) with matel artistical finished. 19 supplying and setting vip pillow size ( 27x17 ) with recron materials. 20 supplying and setting vip pillow cover with bed sheet of soft cloth. 21 supplying and setting vip blanket hypoallerjetic cloth with alovera gel size ( 93 x 73 ) 22 supplying and setting quilt / comforter double gsm white 100% cotton 23 s / f / f matteress make spring well quality 78x72x6 24 s / f / f dinning table eight seater complete made with teak wood, highly melamine polish with onyx italian marble top polish with polyurethene and chair ( high quality fabric ) 25 s / f / f center table size ( 48x48 inch ) with superior quality lamination inside and outside with italian marble top as per direction of e / i 26 s / f / f supplying of one seater premium sofa with febric finish , all complete as per direction of e / i 27 s / f / f supplying of 2 seater premium sofa with febric finish , all complete as per direction of e / i 28 s / f / f supplying of 3 seater premium sofa with febric finish , all complete as per direction of e / i 29 providing & fixing wardrobe with both side laminated inner lining and exterior fitted with hanging rod including all fittings like hing , lock , handal all e.t.c as per instruction of e / i 30 providing and laying 14mmthk fsc certified bamboo wooden flooring of size 125mmx1850mm. the planks shall be provided with tongue & groove required for locking. the flooring to be layer with 5mm underlay foam and 60 microns ldf film placed over it as moisture barrier to proper level with necessary edge profile & transition strip where ever necessary complete as per manufacturers instructions. the rate shall include cost and conveyance of all materials, labour charges, lead, lift, laying self leveling screed 3 5mm thk etc. all complete as specified and as directed by the engineering measurement of flooring will be the actual laid area including skirting and transition bands with the near by floor, skirting where ever applicable ) . 31 providing waterproof texture exterior work by asian paints design dholepur 32 s / f / f board wall partition with itching glass vertical standing position including all materials, labour , taxes all complete as per building specification and direction of e / i framing with wooden beat or 19mm thick centre make water proof ply board both side shuttering with 12 mm thick water proof centure ply veneer 4mm thick veneer of green décor make glass: 5mm thick saint gobine glass 33 supply, fitting, fixing and testing of dtreet light led lighting luminaire aerodynamically shaped single piece pressure die cast aluminum luminaire with high power leds as light source and electronic driver ( ip65 ) , along with 90 / 100w led lamp, as energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover, reflector and heat resistant toughened flat glass cover ( ip 65 ) and in compliance to iec safety standards. lm 79 and lm 80 reports to be submitted with all accessories. make: philips / trilux / jaguar / lighting technology. 34 supplying and fixing tpn sheet enclosure on surface or recess along with 25 / 32 amp 415 volts, , c curve, tp mcb complete with connections, testing and commissioning etc. as required. make ( legrand / l&t / siemens / schneider ) 35 supplying and fixing tpn sheet enclosure on surface or recess along with 63 amp 415 volts, , c curve, tp mcb complete with connections, testing and commissioning etc. as required. make ( legrand / l&t / siemens / schneider ) 36 supplying and fixing of modular type 25 ac unit box with on / off mcb on surface or in recess complete with connections, testing and commissioning etc. as required. ( to use for split ac ) make ( legrand / l&t / siemens / schneider ) 37 luminaires supplying and fixing recess mounted 18 watt led ( warm light ) ( 100 lm / w ) vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceiling including connection with 1.5 sq. mm fr pvc insulated copper conductor cable and earthing the body etc. as required. make : .trilux / lighting technology / philips / jaguar. 38 supplying and fixing single wall mounted 9 / 11 watt ( 2ft long ) led warm light ( 100 lm / w ) type batten fitting complete with electronic diver and led etc. directly on wall / ceiling including connections with 1.5 sq. mm fr pvc insulatted copper conductor and earthing the body etc. as requiered. ( to use as mirror light in toilets ) make : trilux / lighting technology / philips / jagaur. 39 suppling and fixing of recess / surface 23 / 24watt ( 1ftx1 ft ) led ( warm light ) 100lm / w, downlighter complete with electronic diver and led etc. directly on wall / ceiling including connections with 1.5 sq. mm fr pvc insulatted copper conductor and earthing the body etc. as requiered. ( to use in double height area ) make : trilux / lighting technology / philips / jagaur. 40 suppling and fixing of surface 15 / 18watt led downlighter ( warm light ) 100lm / w etc. directly on wall / ceiling including connections with 1.5 sq. mm fr pvc insulatted copper conductor and earthing the body etc. as requiered. make : trilux / lighting technology / philips / jagaur. 41 supplying and fixing 4 long 1x 40 watt or ( 2x20w ) suspended type led ( warm light ) ( 100 lm / w ) luminaire provides soft light and glare free symmetrical illumination complete with all accessories etc. including ball and socket arrangement, 2 no. down rods of 20mm dia x 1.6 mm thick g.i. pipe upto 30 cm. length, painting and wiring the down rods and connection with 1.5 sq mm fr pvc insulated copper conductor, single core cable and earthing etc. as required. make : .trilux / lighting technology / philips. / jaguar 42 supplying and fixing following watt led flood light luminaire with integral control gear, lenses, heat resistant toughened clear glass cover, with black powder coated aerodynamically shaped single piece pressure die cast aluminum luminaire with high power leds as light source and electronic driver ( ip65 ) , along with 120 led warm light, ( 4000k ) as energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover including connections with fr pvc insulated copper conductor cable and earthing the body along with all fixing accessories etc. as required, with proper iron clamps, nut bolts with washers etc. to fix on minimum 65 mm dia g.i. pipe in front of stage of auditorioum of museum as per direction of e / i or consultant as per drawing prescribed reflector and heat resistant toughened flat glass cover ( ip 65 ) and in compliance to iec safety standards. lm 79 and lm 80 reports to be submitted. make : trilux / lighting technology / philips / jagaur. 120 w led flood warm light ( 3000k ) 43 supplying and fixing surface mounted 10 / 12 watt led type bulk head e comprising of pressure die casr housing with acrylic diffuser ( ip65 ) and complete with integrated electronic driver etc. directly on wall / ceiling including connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc as required. make : trilux / lighting technology / philips / jagaur. 44 supplying and fixing 25 / 30 watt led type post top lantern suitable for garden / park / gate light complete with integrated electronic driver and all accessories including connection with pvc insulated copper conductor cable and earthing the body etc. as required and in compliance to iec safety standards. lm 79 and lm 80 reports to be submitted . make: philips / trilux / wipro. / lighting technology. 45 supplying and fixing of decorative wall bracket fixture in chromne finish with glass diffuser suitable for 2 x15 watt cfl / led lamp directly on wall including connection with 1.5 sq. mm fr pvc insulated copper conductor cable and earthing the body etc. as required. ( but without lamp ) make: philips / trilux / crompton / havells / jagaur.cost of decorative wall bracket fixture 46 supply of 15 watt led lamp. ( luminous flux 600lm, cct 6500k ( cool white ) , cri 80, rated voltage 220v / 240v. beam angle 120 degree, life 25000hrs. ) make: philips / trilux / havells / jagaur.tel. solution providing, fixing, connecting & testing of krone box ( telephone tag block ) in a thermoplastic, ip 65 ( weather proof ) enclosure, internally embedded gasket, anti corrosive, insulated and shock proof with provision for cable through ip 65 glands complete in all respects. ( make : matrix / alcatel / avaya. ( cost from gem ) 47 10 pair tag block ( krone box ) ( 136 mm x 253 mm x 115 mm ) 48 20 pair tag block ( krone box ) ( 136 mm x 253 mm x 115 mm ) 49 50 pair tag block ( krone box ) ( 300 mm x 300 mm x 70 mm ) providing, laying, connecting, testing & commissioning of multi core telephone un armoured cables of conductor size 0.5 sq.mm. annealed tinned electrolitic grade copper, pvc insulated, twisted pairs bunched together, over all pvc sheathed, gi strip or wire armouring laid on existing cable tray or along the wall or laid in pipes or in trenches including excavation of cable trench, sand filling covering with bricks and back filling complete as required. ( make : finolex / polycab / havells ) 50 10 pair pistl10pxo. 51008 51 20 pair 52 50 pair 53 supply and installation of digital telephone set with caller id system with connecting cord and jacks at user end. ( provision of id caller telephone for reception ) make: ( beetel / panasonic / orpat ) . 54 ip pbx system: supply, fitting, fixing, commissioning and testing of ip based 100% non blocking ip pabx system should be a ip compatible with rich feature set of the system and can be connected with pure voice over ip ( voip ) communication network across corporate local and wide area networks ( lan and wan ) as & when required. central processing unit: the system main software should be open architecture based. the cpu of main system shall be 32 bit processor working at 2.0 ghz or better. the system should be wall mountable. • system architecture should be latest pure ip and should be wall mountable meet me conference 30 party x 2 from day 1 must be available. must support unified communications equipped with 64 analog extensions 32 ip extensions alongwith ip user license loaded from day expandable upto 256 ip extensions, voip card in built charger, battery with one our back up facitity. 32 analog trunk ports, 1 pri , 02 ports auto attendant ipabx. make: avaya / nec / alacatel 9 u wall mount eqauipment rack 55 sitc of of 9u wall mounted networking cabinet 504.65x600x500 ( hxwxd ) : rack must be along with the following components like; width ( mm ) 600, depth ( mm ) 500, approx.net wt ( kg ) 20, crca d grade thickness ( mm ) 1.2, ral 9017 ( matt black ) , glass 4mm toughened tinted glass door, accessories:, cooling fan ( 230v a / c 90 cfm ) 2 nos, pdu 230vac 1 no, cable manager metal 2 nos, mounting hardware ( 20 sets of m6 screws, washer, cage nuts ( nickel coated ) ) 1 no, wall screws ( 4 sets of 2 screws, washer, rubber grommet ( nickel coated ) ) 1 no, door lock 1 no, front metal band 1 no. in the rack there must be maintained 1 u = 1.75 inches space. ( make : make : legrand valrack / netrack / rittal / schneider / ortronics or as approved by architect ) . ( for lan ) cost of wall mount 9 u network rack 56 surveillance ( cctv system ) sitc of 2 mp bullet varifocal ip ( ir ) indoor bullet camera ( 2.8 12mm lens ) ( matrix ) , 3 years warranty, day night type, 1 / 2.8progressive scan cmos, 1920 × 1080 at 25fps, 2.7 to 13.5 mm lens, 0.01 lux at f1.2, 0 lux with ir, icr, onvif ( profile s, profile g ) , support h.265, h.264, mjpeg, 120db wdr, 3d digital noise reduction, three individually configurable stream, 12 vdc & poe, ir range: 40m, support on board storage up to 128 gb ( sd card not included ) , alarm: 2 inputs & 2 outputs, audio: 1 input & 1 output, ip67, edge anlalytics line crossing detection, intrusion detection, scene change detection, motion detection, face detection, audio exception detection, video tampering, ul, fcc, ce certified. make axis / hikvision / pelco / honeywell or as appoved by architect / consultant. 57 sitc of matrix 2 mp ip mini dome indoor camera with 3.6 fixed lens, audio support, 3 years warranty, resolution d1 ( 704 x 480 pixel ) , hd ( 1280 x 720 pixel ) , full hd ( 1920 x 1080 pixel ) day night type, ( progressive scan cmos, 1920 × 1080 at 25fps, 2.7 to 13.5 mm lux at f1.2, 0 lux with ir, icr, onvif ( profile s, profile g ) , support h.265, h.264, mjpeg, 120db wdr, 3d digital noise reduction, three individually configurable stream, 12 vdc & poe, ir range: 40m, support on board storage up to 128 gb ( sd card not included ) , alarm: 2 inputs & 2 outputs, audio: 1 input & 1 output, ip67, edge anlalytics line crossing detection, intrusion detection, scene change detection, motion detection, face detection, audio exception detection, video tampering, ul, fcc, ce certified.make axis / hikvision / pelco / honeywell or as appoved by architect / consultant. 58 sitc of 2mp ir bullet fixed camera 1 / 2.8progressive scan cmos, 1920 × 1080 at 25fps, 2.8 mm fixed lens, 0.01 lux at f1.2, 0 lux with ir, icr, onvif ( profile s, profile g ) , support h.265, h.264, mjpeg, 120db wdr, 3d digital noise reduction, three individually configurable stream, 12 vdc & poe, ir range: 40m, support on board storage up to 128 gb ( sd card not included ) , ip67, edge anlalytics line crossing detection, intrusion detection, motion detection, scene change detection, video tampering, ul, ce, fcc certified. make axis / hikvision / pelco or as appoved by architect / consultant. 59 sitc of 32 ch nvr with 32 tb storage ( sparsh ) ( sparsh & sr nv32f608 he ) connect up to 32 ip support cameras, 2 u rack mounting confrigation dual os design, up to 12 megapixels resolution, 2 hdmi output with one atleast at 4k ( 4096×2160 ) , 1 vga output with 2mp resolution, support h.265 / mjpeg, incoming bandwidth 500 mbps, 8 sata hard disks, anr technology, 16 sata interfaces for 8 hdds and capacity of each hdd upto 8 tb, front panel: 1 × usb 2.0 rear panel: 2 × usb 3.0, alarm i / o 16 / 4, rs 485, 4 rj 45 10 / 100 / 1000 mbps self adaptive ethernet interface, multiple network monitoring: web viewer, ce, fcc, ul certified with survelliance sd crad , with 8 tb storage ( inclusive of 8 tb surveillance hard disk: 4 nos. ) make axis / hikvision / pelco or as appoved by architect / consultant. 60 6 u wall mount equipment rack sitc of of 6u wall mounted networking cabinet 504.65x600x500 ( hxwxd ) : rack must be along with the following components like; width ( mm ) 600, depth ( mm ) 500, approx.net wt ( kg ) 10 12, crca d grade thickness ( mm ) 1.2, ral 9017 ( matt black ) , glass 4mm toughened tinted glass door, accessories:, cooling fan ( 230v a / c 90 cfm ) 2 nos, pdu 230vac 1 no, cable manager metal 2 nos, mounting hardware ( 20 sets of m6 screws, washer, cage nuts ( nickel coated ) ) 1 no, wall screws ( 4 sets of 2 screws, washer, rubber grommet ( nickel coated ) ) 1 no, door lock 1 no, front metal band 1 no. in the rack there must be maintained 1 u = 1.75 inches space. ( make : make : legrand valrack / netrack / rittal / schneider / ortronics or as approved by architect ) . 61 sitc of 43 lcd 24x7 surveillance monitor ( ( smart tv ) . make lg / samsung or as appoved by architect / consultant. make: sony, lg, panasonic t, v. set 62 sitc of 55 full hd 1080p led tv.; firstouch smart television tv 55inch led backlit lcd , resolution ( pixels ) ( 3840x2160 ) uhd, screen size 55 , smart tv, details of accessories ( included in the scope ofsupply ) : remote control, connecting cable, batteries, dimensions ( length xbreadth x depth ) 52” x 1.2” x 31.4. wall mount. power consumption 138 watt. wifi direct, built in wifi. make soni / lg, / samsung / panasonic. cost of 55 full hd led panel tv ( cost without gst ) 63 electrical appainces refrigerator supply, fitting, fixing and testing of eie 220 l 3 star direct cool double door refrigerator ( eie ) refrigerator is:1476 latest for direct cool with following specifictions: ( make: sansui / samsung / haier / lg / kelvinator. capacity: 220 lit. power requirement: 220 240 v, 50 hz insulation: puff eco friendly refrigerant compressor type: power saver compressor defrosting type: direct cool type: single door built in stabilizer: yes warranty: 1 year cost of refrigerator 220 lit. 64 supply, fitting, fixing and testing of liebherr 420 l 2 star frost freedouble door refrigerator ( liebherr ) ( tdcs 4740 ) refrigerator conformity to indian standrad : is:15750 ( 2006 ) for frost free latest for direct cool with following specifictions: . ( make: sansui / samsung / haier / lg / kelvinator ) capacity: 420 lit. power requirement: 220 240 v, 50 hz insulation: puff eco friendly refrigerant compressor type: power saver compressor defrosting type: direct cool type: single door built in stabilizer: yes warranty: 1 year cost of refrigerator 420 lit. 65 supply, fitting, fixing and testing of 3 star direct cool single door refrigerator is:1476 latest for direct cool with following specifictions: . make: sansui / samsung / haier / lg / kelvinator capacity: 80 lit. power consumption: 289 kwh / yhr power requirement: 220 240 v, 50 hz insulation: puff eco friendly refrigerant compressor type: power saver compressor defrosting type: direct cool type: single door built in stabilizer: yes warranty: 1 year total cost of refrigerator. 66 supply, fitting, fixing and testing of microwave oven 900 w 5 star rating 23 l along with the microwave oven will automatically protect you in the offset of an accident and facilities with timer, preheat, defrost, reheat, convection heating, touch contol pannel, adjustment of microwave power, conformity to indianstandard is 11676, heatingchamber stainless steel, along with all accessories & 1 year warranty. make: godrej gmx 25ca1 miz / samsung ce1041dsb2 / haier / lg. 6 kva ups 67 supply, fitting, fixing, testing and installation of 6.0 kva, technology igbt pwm withoutinbuilt isolationtransformer, input power single phase 160v 260v sinewave, 50hz & single phase 230v output on line ups system with 12v / 26 ah sealed maintenance free batteries backup protection for 90 minutes and all accessories as required of reputed make ups. with 46 nos. 26ah, 12v battery. make: apc / emerson / numeric. details of ups : technology : micro processor based controls, true online, double convertion type, should have cold start facility. overall efficiency :> 90% isolation ; built in isolation transformer at the output of ups system. charger : should have built in charger of minimum 10 amp. back up time : 90 min. with smf batteries. vah required : minimum 14352 for 6 kva ( 26h x 46 n0s.x 12v ) = 14352vah ) display : should have lcd display with event logging facility. upgradeability : should have upgradable to work as parrallel redundent ups in load sharing mode. shoftwere comunication : should have snmp ( simple network management protocol ) compatability ( optional ) . input current harmonic shall be less than 3% with the application of igbt ( insulated gate bypolar transistor ) best rectifier, but 6 / 12 pulse is not applicable. sealed maintenance free smf batteries for 6kva ups for 90 mins. backup with open type cabinate for installation of batteries and their respective battery leads copper cables / buslinks between batteries, copper cables between ups & batteries, with dc mccb box and required capacity of mccb. make : global yuasa / exide / uplus / hbl cost of sealed maintenance free smf batteries with stand with 6kva ups. 68 water purifire supply , fitting fixing and commissioning of indian water inc. pure waterfor life fully automatic with autocut off ro potable waterpuri 2000 plus 25 litre ro+uv+uf water purifier electrically oparated • purification technology ro+uv+uf• capacity 25 litre • filter pre filter ( optional ) , sediment filter, activated carbon filter, anti scalant filter, post uf filter, • membrane type 80 gpd, • power features • power requirement 110v 300v, 50 hz, • operating voltage 24v dc v along with all required accessories, like, connecting wires, pipes, stand and fixing euipments along with drain pipe in put pipe and etc as required. make aquagard, voltas, kent.cost of water purifire indian water inc. pure waterfor life 2000 plus 25 litre ro+uv+uf water purifier electrically oparated • purification technologyro+uv+uf• capacity 25 litre • 69 1.5 ton 5 star split ac supply , fitting, fixing and testing of 1.5 ton 5 star high wall split ac ( cooling only ) unit of bee 5 star rating, etc as required. make: hitachi / daikin / carrier mitsubishi. 3 ton 4 star cassette ac 70 supply, fitting, fixing and testing of 3 ton 4 star ceiling mounted ( cassette ac cooling ( hdum100cr s / hdc100cr 5 ) ) unit of bee 4 star rating, etc as required. make: hitachi / daikin / carrier. mitsubishi. 4 ton 4 star cassette ac 71 supply, fitting, fixing and testing of 4 ton 4 star ceiling mounted ( cassette ac cooling r410a ) ) unit of bee 4 star rating, etc as required. make: hitachi / daikin / carrier. mitsubishi. 72 installation charge of cassette ac 73 copper pipe with insulation 74 hard pvc drain pipe 75 4 core 4sqmm copper cable 76 bracket for outdoor unit of ac 77 led cove linea plus ( strip ) sitc of 5 mtr set led cove linea plus ( warm light ) led 25 w tape with driver ( blue or yellow in colour ) easy to install, maintain and comes with suitable driver energy saving strip tape light ( 3000 / 4000 ) base & lamp . for architectural: accent , good protection against water and dust ingress and impact, with all accessories. ( indoor application ) make make: philips / equivallent in trilux / jaguar / lighting technology track light 78 supply, installation, testing and commisning of 26 / 30w track mounted accent lighting luminaire with compact housing and slim gear box with color rendering index of 90 for architectural: accent , good protection against water and dust ingress and impact, led track with option of one meter track. make: philips flex acent g 2, st391t led20 / 930 psu e nb 1c wh in / equivallent in trilux / jaguar / ( 3000 / 4000k ) track integral bollards: 79 providing, fitting, fixing and testing of bollard light decorative luminaire light fixture of 800mm in length ( ip 65 ) 9 / 10 w led lamp available in cct of 3000k / 4000k with integrated baseplate and driver for easy installation, operating voltage of 220 240 v, wide beam optics and transluscent diffuser tube. the fixture should have extruded aluminium housing and heat resistant silicone rubber gasket, operating temperature ranging from 20° c to 40°c, the fixture should have ip65 protection and ik10 impact resistance. driver shall be high efficiency having efficiency > 85% and in compliance to iec standards. with foundation, commissioning, testing all with all other accessories as per drawing provided at the time of work execution or as per the direction of e / i ) make philips bcp150 led150 / nw psu 220 240v 7043 9w / trilux dtindlbled 800 840et 10w / jaguar / lighting technology / havells cost of bollard light fixture with 9w led lamp cost of terminal box ( size 8 x 6 x 4 ) of 2 mm crca sheet steel powder coating with locking arrangement and rubber gasket etc. 2a sp mcb make l&t, hager, legrand 2 nos. stud type 4 studs 20a connector ( 1 no. for incomer and 2nd for outgoing cable ) total cost of bollard light with all above accessories. 80 step light ( out door application ) sitc of step light ( warm light ) robust design led 4 w step light is ip67 / ik10, easy to install, maintain and comes with suitable mounting box, energy saving step light grey clour packed with features applications ( 3000 / 4000k0 . for architectural: accent , good protection against water and dust ingress and impact, with all accessories. ( steps of open air theater out door application ) make make: philips bwg150 led50 / nw psu 220 240v ip67 7043 / trilux / jaguar / lighting technology / havells. 81 garden spike light ( out door application ) supply, installation, testing and commisning of 12w led garden spike light ( cob integrated lighting ) solution lighting family for architectural: accent , good protection against water and dust ingress and impact, with all accessories. ( ip 67 out door application ) make: philips / trilux / jaguar / lighting technology / havells. 82 supply, fitting, fixing of wall mount suitable capacity ( 4 kva ) automatic voltage stabilizer, voltage range 130v to 280v of copper wound transformer along with suitable size of connecting 3 mtr 3 core 2.5 sq. mm flexible copper cable ( indoor unit to stabilizer ) make v guard / totaline / sen & pandit. 83 25a 2 / 3 module switch and socket ( for geyser ) : supplying fixing and testing of 25 amps 240 volts 2 / 3 module separate switch and socket in existing g.i.box with front plate in recess, for the switch and with indicator, socket outlet to be installed in different locations as shown in drawing and complete with connections, testing and commissioning etc. as required. make: legrand ( arteor ) / schneider ( zencelo ) / mk ( blenz ) suppy of electric kattle along with all accessories and following specifications: . capacity: 1.7 / 1.8 lit. consume: 1800 2200w suitable for tea, water & soups. auto switch off facility body type: metal body stainless type warrenty: 2 year make: philips / bajaj / havells cost of electric kattle 84 electronic hooter: supplying, installation, testing and commissioning of duel tone electronic hooter suitable for wall mounted complete as required. 85 main lt panel supply, designing, unloading , shifting to location, manufacturing and effecting proper connection installation, testing and commissioning of all incomer and outgoing of lt panel fabricated out 2 mm ( 14 swg ) crca sheet steel dust, damp and vermin proof ( ip 42 ) free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 hz ac 3 phase 4 wire system, hinged doors of 2mm thick crca sheet, duly painted ( powder coated ) complete with aluminium bus bars, interconnection with frls pvc copper wire, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. the sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 nos. earth studs. the panels shall be preferably arranged in multitier formation. these shall be of adequate size with a provision of 10 percent vacant space to accommodate future additional switch gear in addition to spare feeders presently provided. the size of the panel shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component do not attain temperature rise more than 40 degree celsius. location : in panel room. the name plate for each feeder must be in anodized aluminium sheet. panel size as per drawing and shall be provided at the time of work order. al. bus bar the panel includes 415v, 400 a, 3ph, 36ka, 50hz electrolytic aluminium bus bar ( e91ewp ) aluminium earth bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. the electrolytic aluminium bus bar of grade 63401 wp as per i:s 5082 of suitable length and insulated by heat shrinkable sleeves red, yellow, blue and black as r y b & n. the current density of bus bar shall be minimum 0.8 a / sq mm. minimum clearance between live parts / neutral to earth shall be 19mm. however clearances between terminals at components shall be as per applicable individual standard for components. interconnections between the main bus bars and individual units shall be made with 2.5, 4, 6 & 10 sq mm frls pvc cu. wire with 35 & 63mm 4 studs ( brass ) treminal blocks, aluminium bus bars of adequate rating. al. bus bar will be supported on insulators made of non hygroscopic, non inflammable material with tracking index equal to or more than that defined in bis contractor will provide shop drawing sld & ga drawing along with bom with cat. no. of each and every components and switch gears of lt panel for approval of consultant. inspection of the lt panel shall be carried out at panel builders factory by the consultant before final delivery for that all arrangements shall be made by the contractor. all 4 pole mccb with thermomagnetic based release must have follwing characterstics: 1. icu=100% ics. 2. with positive isolation marked. 3. with adjustable short circuit and over load. 4. as per iec 60947 2. make of mccb l&t d sine / legrand dpx³ / schneider nsx / siemens 3vl. make of mcb ( 10ka c series. ) l&t u version / legrand dx³ / schneider acti / siemens. bill of material of main lt panel: 1 set of fabrication part of lt panel & busbar system, in crca sheet steel enclosure ( ip 42 / 43 ) without any components & its busbar system, in crca sheet steel enclosure without any components. name of panel builder : jmd electrotech, kokar, arnav poertech, tatisilway, tts systematix private ltd, tatisiway, meditron, meshra, ranchi or any approved panel builders of above make switch gears. indicating 1 sets multifunction meter having led display accuracy class 1 as per iec 62053 21, rs 485 port, ( ethernet / modbus ready suitable for monitoring and control with bms system ) in built rtc, aux supply: 44 277vac / dc. parameters: volts, amps, pf, thd, f, w, wh, va, vah, var, varh, runhrs, onhrs interrupts, thd for v&i per phase, individual harmonics for v&i upto 15th level complying with iec61557 12. min / max for eight parameters. sampling rate: 64 samples per cycle. make schneider / satec / siemnes 3 nos. ct of 400 / 5va 5 class one epoxy resin cast ct ( 3 nos. ) =1 set. make: kappa / matrix 3 sets phase indicating light shall be protected by 2 amps sp mcbs for incomer & outgoing.make l& t / ae / schneider. interlocking provision of mechnical interlocking between 400a / fp / 36ka mccb as common incoming and 1 no. of 400a on load change over for d.g incomer, in such a way so that the two supplies are not parallel at any time. incomer : 1 no. 400a fp / 36ka / mccb with adjustable thermomagnetic release type with s / c & o / l protection with with front rotary handle type with spreader links with on off trip indication. ( incoming cable size –1 run 300sq mm 3.5 core al. ar. cable ) . 1 no. 400a tpn on load change over panel mounted open execution typesuitable arrangement for terminal of al. cable out going 1 no. 250a fp mccb ( 25ka ) with adjustable thermomagnetic release type with s / c & o / l protection with front rotary handle type with spreader links with on off trip indication. ( to lt panel of residence ) . ( cable size 1 run, 120 sq. mm. 3.5 core al ar. cable ) 1 no. 200a fp mccb ( 25ka ) with adjustable thermomagnetic release type with s / c & o / l protection with with front rotary handle type with spreader links with on off trip indication. ( for 1 no. for lt panel of office ) cable size 1 run, 120 sq. mm. 3.5 core al ar. cable ) 5 nos. 63 a fp mccb ( 25ka ) with adjustable thermomagnetic release type with s / c & o / l protection with front rotary handle type with spreader links. with on off trip indication. ( 2 no. for out door feeder pillar panels, 1 no. for tpn db out house, 2 nos. as spare ) 4 nos.25a / fp / 25ka / mccb thermomagnetic release type, on of trip and s / c , o / l protection, on off indication with rotary handle & spreader links. ( 1no. for pump motor, 2 nos. as future use and 1 no as spare ) 2 nos. 32a 10 ka, dp mcb c series 2 nos. 63a 10 ka, dp mcb c series total cost of main lt panel lt panel residence 86 supply, designing, unloading, shifting to location, manufacturing and effecting proper connection installation, testing and commissioning of all incomer and outgoing of lt panel fabricated out 2 mm ( 14 swg ) crca sheet steel dust, damp and vermin proof ( ip 42 ) wall mounting factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 hz ac 3 phase 4 wire system, hinged doors of 2mm thick crca sheet, duly painted ( powder coated ) complete with aluminium bus bars, interconnection with frls pvc copper wire, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. 87 the sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 nos. earth studs. the panels shall be preferably arranged in multitier formation. these shall be of adequate size with a provision of 10 percent vacant space to accommodate future additional switch gear in addition to spare feeders presently provided. the size of the panel shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component do not attain temperature rise more than 40 degree celsius. location : suitable location the name plate for each feeder must be in anodized aluminium sheet. panel size as per drawing and shall be provided at the time of work order. al. bus bar the panel includes 415v, 300 a, 3ph, 25ka, 50hz electrolytic aluminium bus bar ( e91ewp ) aluminium earth bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. the electrolytic aluminium bus bar of grade 63401 wp as per i:s 5082 of suitable length and insulated by heat shrinkable sleeves red, yellow, blue and black as r y b & n. the current density of bus bar shall be minimum 0.8 a / sq mm. minimum clearance between live parts / neutral to earth shall be 19mm. however clearances between terminals at components shall be as per applicable individual standard for components. interconnections between the main bus bars and individual units shall be made with 2.5, 4, 6 & 10 sq mm frls pvc cu. wire with 35 & 63mm 4 studs ( brass ) treminal blocks, aluminium bus bars of adequate rating. al. bus bar will be supported on insulators made of non hygroscopic, non inflammable material with tracking index equal to or more than that defined in bis contractor will provide shop drawing sld & ga drawing along with bom with cat. no. of each and every components and switch gears of lt panel for approval of consultant. inspection of the lt panel shall be carried out at panel builders factory by the consultant before final delivery for that all arrangements shall be made by the contractor. all 4 pole mccb with thermomagnetic based release must have follwing characterstics: 1. icu=100% ics. 2. with positive isolation marked. 3. with adjustable short circuit and over load. 4. as per iec 60947 2. make of mccb l&t d sine / legrand dpx³ / schneider nsx / siemens 3vl. make of mcb ( 10ka c series. ) l&t u version / legrand dx³ / schneider acti / siemens. bill of material of main lt panel: 1 set of fabrication part of lt panel & busbar system, in crca sheet steel enclosure ( ip 42 / 43 ) without any components & its busbar system, in crca sheet steel enclosure without any components. name of panel builder : jmd electrotech, kokar, arnav poertech, tatisilway, tts systematix private ltd, tatisiway, meditron, meshra, ranchi or any approved panel builders of above make switch gears. indicating 1 sets multifunction meter having led display accuracy class 1 as per iec 62053 21, rs 485 port, ( ethernet / modbus ready suitable for monitoring and control with bms system ) in built rtc, aux supply: 44 277vac / dc. parameters: volts, amps, pf, thd, f, w, wh, va, vah, var, varh, runhrs, onhrs interrupts, thd for v&i per phase, individual harmonics for v&i upto 15th level complying with iec61557 12. min / max for eight parameters. sampling rate: 64 samples per cycle. make schneider / satec / siemnes 3 nos. ct of 300 / 5va 5 class one epoxy resin cast ct ( 3 nos. ) =1 set. make: kappa / matrix 3 sets phase indicating light shall be protected by 2 amps sp mcbs for incomer & outgoing.make l& t. / ae / schneider. incomer : 1 no. 250a fp / 25ka / mccb with adjustable thermomagnetic release type with s / c & o / l protection with front rotary handle and spreader links with on off trip indication. ( incoming cable size –1 run 120sq mm 3.5 core al. ar. cable ) . out going 7 nos. 63 a fp mcb 10ka c series . ( 3nos. for power db, 2 nos. as future use & 2 nos. as spare ) 4 nos. 32 a fp mcb 10ka c series . ( 4 nos. for cassette units and 1 no. as spare ) 5 nos. 25a fp mcb, 10ka c series . ( 3 nos. for ldb db, 1 nos. as spare ) 4 nos. 32a 10 ka, dp mcb c series 4 nos. 63a 10 ka, dp mcb c series total cost of lt. panel ( b ) feeder pillar panel ( canopy type ) : 88 supplying, designing, unloading, shifting to location, manufacturing installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of double door canopy type feeder pillar panel for external lighting of 14 swg crca sheet ( 2 mm ) steel ip – 54 floor mounting cubical type lt panel in canopy shape suitable for operation on 415v, 50hz, 3 ph. ac supply and fault level 25 ka with front operated construction including separate fabrication arrangement for fixing m.c.c.b. the sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized with locking arrangement duly fixed on base channel size – 50 mm x 50 mm x 4 mm having accessories mounted inside the cubical panel, earthing with 2 nos. earth studs. the panel shall have type test certificates with short circuit and ip protection ( c.p.r.i. test ) . detail drawings and sld shall be provided at the time of work order. all openings shall be covered by soft rubber gasket, enclosure shall be galvanized. panel shall have suitable cable entry from bottom and suitable arrangement for multi runs aluminum cables for all mccb. the panel shall have type test certificates with short circuit and ip protection ( c.p.r.i. test ) aluminum bus bar for panel : bus bar shall be suitable for 100a, tpn busbar chamber of suitable length with ( e91ewp ) eletrolytic aluminum busbars. all busbars and interconnections shall be of suitable size aluminum busbar, current density of aluminum shall not be more than 0.8 amps / sq.mm cross sectional area of bus bar with removel gland plates, cable glands, at sending and receiving ends, encluding connections with outgoing feeders complete in all respect and all interconnections shall be made with 2.5, 4 and 6 sq.mm. pvc cu.wire. cost of enclosure with al bus bar, connection pvc wires, etc. the aluminium bus bar shall be with heat shrinkable pvc slived red, yellow, blue & black as ( ryb & n ) after temperature and incloser derating maximum allowable temp.of bus bar shall be 90 degree c. sld will be submitted by the contractor for approval to engineering incharge / consultant before submitting the apafcr panel drawing. based on approved sld, contractor will provide the ga drawing of external feeder pillar panel. inspection of the external feeder pillar panel shall be carried out at panel builders factory by the consultant before final delivery. 1 set of fabrication part of feeder pillar lt panel & busbar system, in crca sheet steel enclosure ( ip 42 / 43 ) without any components & its busbar system, in crca sheet steel enclosure without any components. name of panel builder : jmd electrotech, kokar, arnav poertech, tatisilway, tts systematix private ltd, tatisiway, meditron, meshra, ranchi or any approved panel builders of above make switch gears. the panel builder shall have type test certificates with short circuit and ip protection ( c.p.r.i. approved ) make of mccb l &t d shine. / legrand dpx³ / schneider nsx / siemens 3vl / equivallent in abb location : in campus bill of material in external feeder pillar panel : incomer: 1 no. 63a / fp / 25ka / mccb thermomagnetic release type with rotary handle & spreader links with on off trip indication. 3 set of ct 100 / 5va 5 class one epoxy resin cast ct ( 3 nos. ) =1 set. make matrix / kappa / l&t 1 set of analogue am meter ( 0 – 100a ) 96mmx96mm 4 position with selector switch for incomer. make l& t. / ae / schneider. make kaycee / l&t / schneider. 1 set of analogue voltmeter ( 0 – 500v ) 96mmx96mm with 4 position selector switch for incomer. make l& t. / ae / schneider. make kaycee / l&t / schneider. 3 sets of phase indicating light shall be protected by 2 amps sp mcbs for incomer.make l& t. / ae / schneider. out going 3 sets 25a / fp / 25ka / mccb adjustable thermomagnetic release type, and s / c , o / l protection, with rotary handle & spreader links. with on off trip indication. ( 2 no . for external lighting and 1 no. as spare ) 2 nos. 4 pole 25 a power contactor no nc of three phase of suitable rating. make: l&t / siemens / legrand 2 nos. single channel digital time switch. make: alpha rex 3 – cat no. ( d21 astro, 1 channel. ) 412654 2 nos. four pole two way lexic changeover with centre off 440v ac 32 to 40a to be used in case of timer failure to by pass the timer. ( legrand cat no. 604022 ) total cost of feeder pillar panel for external lighting copper cable for outdoor units 89 supply of following size of 1.1kv xlpe / pvc insulated / pvc sheathed ( heavy duty ) unarmoured electric cable with copper conductor as per is 7098 ( part 1 ) 1988 with upto date amendments. make: havells. polycab. kei, gloster. supply of 4 core 10 sq. mm. xlpe pvc cu. / unarmoured cable 1.1ar. cable telephone system accessories for matv network system 90 supply, erection, testing and commissioning of splitter / tap off mounted in suitable sizes ms boxes for matv system and shall be suitable for interactive system.two way ( s 2 ) 91 four way ( s 4 ) 92 two way tap off ( t2 ) 93 four way tap off ( t4 ) active components: l2 poe access switch 94 supply, fitting, fixing, connecting and testing of switch with 24 x 10 / 100 / 1000t poe ports and 4 x 100 / 1000x sfp ports, switching capacity 56gbps and forwarding rate 41.7mpps, switch should support poe and poe+ with 370w minimum power budget, operaating temperature 0°c to 50°c, switch should support link reccovery within 50ms for ring architecture, sdn or similar kind of technolgy should support, warranty 5 year from day 1 . make: cisco ws c2960x 24ps l / allied telesis at x230 28gp / hp / juniper ex2200 24p ) the above l2 managed data switch consists of the following: 1. power cord india, right angle. 2. both side cable connector. 3. 1 year free service pack. interface 24 x 10 / 100 / 1000t ports and 4 x 100 / 1000x sfp ports switching capacity / forwarding rate : 56gbps / 41.7mpps performance: up to 16k mac addresses, 256mb ddr sdram management: console port, gui, telnet, ssh, snmpv1, 2 and 3, powerful centralized management and zero touch device installation and recovery like sdn, security: console port, gui, telnet, ssh, snmpv1, 2 and 3, powerful centralized management and zero touch device installation and recovery like sdn, routing: ipv4 static routing and rip. fail over: switch capable of recovery within 50ms in a ring for application high availability ipv6: device management over ipv6 networks with snmpv6, telnetv6, sshv6 and syslogv6 diagnostic: optical digital diagnostics monitoring, automatic link flap detection and port shutdown, port and vlan mirroring ( rspan ) standard protocol: ieee 802.1q, ieee 802.1w, ieee 802.1s, ieee 802.1p, ieee 802.1ab, ieee 802.1ax, ieee 802.3ad operating temparature: 0°c to 50°c certification: en, ul and rohs warranty: 5 years. cost of l2 managed data switch fiber module 95 providing, fixing, connecting & testing of gigabit fiber module mm, support up to 550mtr ( make: cisco glc sx mmd / allied telesis at spsx / juniper ctp sfp 1ge sx / hp ) router / utm 96 supply, fitting, fixing and testing of utm / router with lan: 2 x 1000x sfp / 2 x 10 / 100 / 1000t rj 45 combo, wan: 2 x 1000x sfp / 2 x 10 / 100 / 1000t rj 45 combo , ha: 2 x 10 / 100 / 1000t rj 45, should support url filtering, dos and ddos attack detection and protection, antivirus, malware protection, static, dynamic ( bgp4, ospf, ripv1 / v2 ) , source based routing, policy based routing and igmpv1 / v2 / v3. warranty 5 year from day 1 ( cisco asa 5516 x with fire power services / allied telesis at ar3050s / juniper srx300 / hp ) the above router consists of the following: cisco 2901 ac power supply ( pwr 2901 ac ) ac power cord ( india, south africa ) , c13, bs 546, 1.8m blank faceplate for hwic slot on cisco isr cisco config pro express on router flash 512mb dram for cisco 2901 2921 isr ( default ) 256mb compact flash for cisco 1900, 2900, 3900 isr ip base license  for cisco 2901 2951 cisco 2901 2921 ios universal 2 port serial wan interface card security license  for cisco 2901 2951 1 year free service pack interface: lan: 2 x 1000x sfp / 2 x 10 / 100 / 1000t rj 45 combo wan: 2 x 1000x sfp / 2 x 10 / 100 / 1000t rj 45 combo ha: 2 x 10 / 100 / 1000t rj 45 processor and memory: 800mhz dual core, 1gb ( ram ) , 4gb ( flash ) firewall / utm ( unified threat manager ) : deep packet inspection, bandwidth limiting control for applications, bridging between lan and wan interfaces, data leakage prevention, url filtering, dos and ddos attack detection and protection, antivirus, malware protection, ( intrusion detection system ) , ips ( inclusion prevention system ) antivirous, anti spywire with 3 yrs subscription. this equipment will also protect & prevent outsider or visitors who are not assined in the existing network i, e office network system can not availed by any otsiders or they can not curropt the network system. ( for active & passive mode ) routing and multicasting: static, dynamic ( bgp4, ospf, ripv1 / v2 ) , source based routing, policy based routing and igmpv1 / v2 / v3 nat: static, ipsec traversal, dynamic napt. high availability: vrrp, vrrpv3 management & authentication: web based gui, industry standard cli, snmpv2 & v3, radius, tacacs+, internal user database, web authentication warranty: 5 years on hardware. cost of router / utm access point 97 supply, fitting, fixing, connecting and testing of wireless access point with ieee 802.11ac dual band radio and embedded antenna with 3x3 mimo, centrally controlled and managed by wlan, multiple ssid with vlan mapping, dynamic rf coverage optimization, warranty 5 year from day 1 ( make: cisco air ap1832i x k9 / allied telesis at tq4600 / juniper wla632 ) active components cctv 98 sitc of 8 port unmanaged network poe switch: l2, unmanaged, 8 100m poe port, 1 100m uplink port, 802.3af / at, poe power budget 123w make: cisco / allied telesis / hp aruba / juniper or as approved by architect. 99 sitc of 24 port unmanaged network poe switch: l2, unmanaged, 24 100m poe port, 1 100m uplink port, 802.3af / at, poe power budget 310w make: cisco / allied telesis / hp aruba / juniper or as approved by architect. 100 geyzer supply, fitting, fixing, installation & testing of water storage 15 liters geyser of bee 5 star rating vertical type acralic rust free body, facility of temperature control , with capillary themostat and thermal cut, isi certified heating element along with inlet & outlet connecting pipe, fixing clamps, fasteners, etc. as required. make: venus / bajaj / havells lt panel office supply, designing, unloading , shifting to location, manufacturing and effecting proper connection installation, testing and commissioning of all incomer and outgoing of lt panel fabricated out 2 mm ( 14 swg ) crca sheet steel dust, damp and vermin proof ( ip 42 ) free floor / wall standing factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 hz ac 3 phase 4 wire system, hinged doors of 2mm thick crca sheet, duly painted ( powder coated ) complete with aluminium bus bars, interconnection with frls pvc copper wire, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. the sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 nos. earth studs. the panels shall be preferably arranged in multitier formation. these shall be of adequate size with a provision of 10 percent vacant space to accommodate future additional switch gear in addition to spare feeders presently provided. the size of the panel shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component do not attain temperature rise more than 40 degree celsius. location : corridor or suitable location the name plate for each feeder must be in anodized aluminium sheet. panel size as per drawing and shall be provided at the time of work order. al. bus bar the panel includes 415v, 250 a, 3ph, 25ka, 50hz electrolytic aluminium bus bar ( e91ewp ) aluminium earth bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. the electrolytic aluminium bus bar of grade 63401 wp as per i:s 5082 of suitable length and insulated by heat shrinkable sleeves red, yellow, blue and black as r y b & n. the current density of bus bar shall be minimum 0.8 a / sq mm. minimum clearance between live parts / neutral to earth shall be 19mm. however clearances between terminals at components shall be as per applicable individual standard for components. interconnections between the main bus bars and individual units shall be made with 2.5, 4, 6 & 10 sq mm frls pvc cu. wire with 35 & 63mm 4 studs ( brass ) treminal blocks, aluminium bus bars of adequate rating. al. bus bar will be supported on insulators made of non hygroscopic, non inflammable material with tracking index equal to or more than that defined in bis contractor will provide shop drawing sld & ga drawing along with bom with cat. no. of each and every components and switch gears of lt panel for approval of consultant. inspection of the lt panel shall be carried out at panel builders factory by the consultant before final delivery for that all arrangements shall be made by the contractor. all 4 pole mccb with thermomagnetic based release must have follwing characterstics: 1. icu=100% ics. 2. with positive isolation marked. 3. with adjustable short circuit and over load. 4. as per iec 60947 2. make of mccb l&t d sine / legrand dpx³ / schneider nsx / siemens 3vl. make of mcb ( 10ka c series. ) l&t u version / legrand dx³ / schneider acti / siemens. bill of material of main lt panel: 1 set of fabrication part of lt panel & busbar system, in crca sheet steel enclosure ( ip 42 / 43 ) without any components & its busbar system, in crca sheet steel enclosure without any components. name of panel builder : jmd electrotech, kokar, arnav poertech, tatisilway, tts systematix private ltd, tatisiway, meditron, meshra, ranchi or any approved panel builders of above make switch gears. indicating 1 sets multifunction meter having led display accuracy class 1 as per iec 62053 21, rs 485 port, ( ethernet / modbus ready suitable for monitoring and control with bms system ) in built rtc, aux supply: 44 277vac / dc. parameters: volts, amps, pf, thd, f, w, wh, va, vah, var, varh, runhrs, onhrs interrupts, thd for v&i per phase, individual harmonics for v&i upto 15th level complying with iec61557 12. min / max for eight parameters. sampling rate: 64 samples per cycle. make schneider / satec / siemnes 3 nos. ct of 200 / 5va 5 class one epoxy resin cast ct ( 3 nos. ) =1 set. make: kappa / matrix 3 sets phase indicating light shall be protected by 2 amps sp mcbs for incomer & outgoing.make l& t. / ae / schneider. incomer : 1 no. 200a fp / 25ka / mccb with adjustable thermomagnetic release type with s / c & o / l protection with front rotary handle and spreader links with on off trip indication. ( incoming cable size –1 run 120sq mm 3.5 core al. ar. cable ) . out going without dg set 3 nos. 63 a fp mcb 10ka c series 4 nos. 25a / fp / 10ka / mcb c series 4 nos. 32a 10 ka, dp mcb c series 2 nos. 63a 10 ka, dp mcb c series total cost of lt. panel ( b ) matv, data networking system & cctv : ( part f ) telephone system data net working system passive component : ( data ) 101 providing, fixing, fitting, connecting and testing of white rj 45 cat 6 data outlet / toolless information outlets with white coloured rj 45 transparent shuttered modular scoket outlets with front plate. etl verified to meet or exceed tia / eia category 6 requirements, universal wiring label permitting to either t568a or t568b, ul listed, for computer networking complete in all respect suitable to fix in modular plate type switch system with connections as required. ( make: legrand arteor 573428 / scheinder zencelo / mk blenz ) 102 supplying, fitting, fixing, connecting and testing cat6 utp rj45 loaded patch panel & connector 24 port loaded 19 panel 1 u, panel: dc01 galvanised sheet steel, compliant with standards: iso / iec 11801 edition 3.0 cenelec en 50173 1 2007 ansi / eia / tia 568 c2 1 iec series 60603 7, nfc 20730, standard 8877 – 603.7, contacts: gold / nickel, thickness of gold > 0.8 μm minimum, equipped with rear cable guide to hold cable during maintenance, the connectors are connected from the front without a special tool. equipped with 4 cassettes of 6 rj45 cat. 6 connectors with toolless fast connection, marked 568 a / b, max. number of connections and disconnections: 5 without replacing the wire, endurance: 2500 operations ( plug in / pull out ) ik03, operating temperature: 40°c to +70°c ( make: legrand arteor 033760 / amps. / schneider. 103 supply fitting, fixing, and testing of blue / yellow color cat6 lcs2 u / utp 1 mtr ( 3.5 ft ) factory made lcs2 patch cord with boot factory crimped pvc, performance at 250mhz should be as per standards iec 61935 2 ed. 3.0 iso / iec 11801, usage temp – 20 to + 60°c, no of twists 500, no of insertions 750, 24 awg for rack end. ( make: legrand arteor 051772 / amp , cat#1859247 4 / schneider ) 104 supply fitting, fixing, and testing of blue / yellow cat 6 lcs2 u / utp 3 mtr ( 10 ft ) factory made lcs2 patch cord with boot factory crimped pvc, performance at 250mhz should be as per standards iec 61935 2 ed. 3.0 iso / iec 11801, usage temp – 20 to + 60°c, no of twists 500, no of insertions 750, 24 awg at end user side. ( make: legrand arteor 051774 / amp , cat#1859247 7 / schneider ) 105 providing, fixing, connecting and testing of modular of 6 port unloaded liu sc type. ( make : legrand.032100 / schneider / amp ) 106 providing, drawing, connecting and testing of 6 core unarmoured unitube multi mode om3 ofc ( fiber optics cable ) from wall mounted rack to server room rack, i, e rack to rack connectivity ) in existing heavy duty 25 mm pvc pipe.make make : legrand cat no 332021 / schneider / tyco. 107 providing, fixing, connecting & testing of blanking plate ( 6xrj45 blanking plate for 19 panel black ) . . ( make : legrand 032129 amp / schneider ) 108 providing, fixing, fitting, connecting and testing of sc pigtial 1 mtr 10 gb 9 / 125, mm make legrand.032241 / schneider / amp 109 providing, fixing, connecting and testing of of 3 duplex sm 9 / 125 sc adapter plate. ( make : legrand 032110 / schneider / amp 110 providing, fixing, fitting, connecting and testing of os1 / os2 sc / lc duplex patch cords 3 mtr, pc ( make : legrand.032605 / schneider / amp ) 111 providing, fixing, connecting & testing of splice tray 12 fiber capacity. : ( make : legrand ( lcs2 ) 032907 / amp / schneider ) ...

Bharat Coking Coal Limited - Jharkhand

28609684 supply of 1. three phase digital voltmeter aux. supply – 90 to 277v, burden – 5va, display 4 digit, 1kv/110v, 6.6kv/110v 2. three phase digital ammeter aux. supply – 90 to 277v, burden – 5va 3. three phase digital energy meter aux. supply – 94 to 270v, 6.6kv/110v, 5a/1a...

Drinking Water And Sanitation Department - Jharkhand

28539166 cost towards supplying, installation, testing and commissioning of lt auto power factor correction (apfc) panel all complete comprising of reputed make & of suitable size mcb, mccb, voltmeter, amp. meter, indicator lamp, contactor, capacitors etc. all complete of different sizes...