37945430 bids are invited for spares for cone crusher a inner eccentric bush pt. no. 01022143930 , b outer eccentric bush pt. no. 700005535t , c socket liner for 4.1 by 4 cone crusher pt. no. 01048726435 , d socket seal ring pt. no. 07012102501 , e socket assy. drg no. 00400051 , f thrust bearing assembly pt. no. 7090020004 total quantity : 12...
37929745 bids are invited for water swivel spares mse ball bearing 3210 , thrust bearing 51113 , water swivel packing kores make water swivel , wash pipe of sandvik make water swivel , wash pipe of kores make water swivel , water swivel packing sandvik make water swivel , ball bearing 5210 , thrust bearing 51211 , o ring for water swivel sandvik make , wash pipe carraleous type , water swivel packing carraleous , thrust bearing 51115 , ball bearing 6309 total quantity : 260...
37658923 tender for e quotation for annual repair maintenance estimate of adityapur water supply scheme. 1 a) 1st phase raw water sitarampur p/p. ( 60 h.p.v.t p/set 3 nos)repairing of 60 h.p,v.t pump dismantlingbowl assembly as per required along with loading, unloading & transportation charge all complete. 2 cost towardsrewinding of 60 h.p.v.t motor with suitable copper wire (32 kgs) and replacing of spare materials like bearing nut bolts as per required with loading, unloadingtransportation charge all complete. 3 cost towards supplying and fitting thrust bearing skf 7320 and 6311 2z for 60 h.p.v.t motor and proper greass etc. all complete 4 cost towardssupplying making & fitting s.s line shaft size 56 mm x 72 long ofn 304 materials, g.m impeller for 3 stage 60 h.p.v.t pump as per size and sample, g.m bush, s.s line shaft , 8 dia m.s spider bearing with rubber cut less bush etc. all complete 5 cost towardsrepairing & rewinding of 315 1/0.4 kv step down transformer with suitable size dpc copper wire (14.7 kg. per coil) varnishing with best quality air drying vanish heating and repairing all required joints including the cost of all required materials such as dpc copper wire, varnishing insulating, stud, transformer oilmaterials, rubberized corrugated sheet nuts, bolts, washer etc. and doing internal wiring properly with all labour 6 cost towards repairing and overhaulingof 400 a ocb make mei taking out damaged spare parts then replacing with all complete 7 cost towards repairing and over hauling of 3 tonne chain pulley block, taken out its damaged spare parts then replacementby new one like chain pulley block, stud nuts & bolts and gear all complete. 8 cost towards repairing of panel board replace by new one like mccb,cable, socket,washer, nuts & bolts, amp. meter, volt meter etc all complete. 9 cost towardsrepairingof 8 dia n.r valve, sluice valve,suction pipe, bend, hydertaking out damaged spare partslike nut bolts, spindle, washer etcthen fitting by new one including the cost of machining turning & finishing all complete. 10 cost towards supplying and laying 25 mm² x 3core pvc insulated copper cable 1.1 kv grade with isi mark 11 cost towardsrepairing & rewinding of 150 kva1/0.4 kv step down transformer with suitable size dpc copper wire (14.7 kg. per coil) varnishing with best quality air drying vanish heating and repairing all required joints including the cost of all required materials such as dpc copper wire, varnishing insulating, stud, transformer oilmaterials, rubberized corrugated sheet nuts, bolts, washer etc. and doing internal wiring properly with all labour 12 (b) 2nd phase raw water sitarampur p/p. ( 100 h.p c/f pump set 2 nos and 90 h.p c/f pump set 1 no. ) dismantling of 90 h.p 1 set and100 h.p 2 sets centrifugal pump and taken out damaged impeller etc. all complete 13 cost towardsrepairing and rewinding of 90 h.p.vand 100h.p sq. cage induction motor 3 phase, 50 cycles 1440 rpm 415 ± 10% volts with super enameled copper wire (34 kgs) and replacing of spare materials like bearing nut bolts as per required with loading, unloadingtransportation charge all complete. 14 cost towardssupplying and fitting skf n – 316 roller bearing (ford.e& nde side of the motor)and 6318 c& 6309 ball bearing for de & de side of the pumpgrease, jute etc all complete 15 cost towardsrepairing and overhaulingof 630 a vcb make abb, taking out damaged spare parts then replacing by new one like ratchet assembly, flush mounting type triple pole, fixed contact, moving contact,arc shield motor and mountingtype of relay etc. all complete. 16 cost towardsrepairingof 6 dia n.r valve, sluice valve, 8 dia foot valve,suction pipe, bend, hydertaking out damaged spare partslike nut bolts, spindle, washer etcthen fitting by new one including the cost of machining turning & finishing all complete. 17 cost towards repairing of g.m shaft bush, neck ring,g.m impeller, tyre coupling set, gland tightnerbearing housing for proper size making and machining and finishing for proper bearing fitting. 18 cost towards repairing & rewinding of 315 kva1/0.4 kv step down transformerreplacing burnt coil studs, transformer oil (300 lits.) insulator, lightening arrestor, with loading, unloading& transportation charge all complete. 19 cost towardsrepairing of fasd starter 2 nos oil immersed star delta starter 1 no. replacing conductor, relay, timerand suitable contact finger. 20 cost towards repairing and over hauling of 3 tonne chain pulley block, taken out its damaged spare parts then replacementby new one like chain pulley, stud nuts & bolts and gear all complete. 21 cost towards repairing of panel board replace by new one like mccb,cable, socket,washer, nuts & bolts, amp. meter, volt meter etc all complete. 22 cost towards supplying and laying 35 mm² x 3core pvc insulated copper cable 1.1 kv grade with isi mark 23 (c) 1st phase clear water sitarampur p/p. (125 h.p c/f pump set 1 no,120 h.p c/f pump set 1 no. 100 h.p c/f pump set 2 nos and 90 h.p c/f pump set 1 no. ) dismantling of the 125 h.p, 100 h.p 2 sets, 120 h.p, 90 h.pinduction motorfrom discharge headand taken out rotor from stator etc. all complete 24 cost towardsrewinding of 125 h.p, 100 h.p 2 sets, 120 h.p, 90 h.pinductionmotor with suitable copper wire (36+ 34+34+ 34+32) kgs) and replacing of spare materials like bearing nut bolts as per required with loading, unloadingtransportation charge all complete 25 cost towardsrepairingof 6 dia n.r valve, sluice valve, 6 dia foot valve,suction pipe, bend, hydertaking out damaged spare partslike nut bolts, spindle, washer etcthen fitting by new one including the cost of machining turning & finishing all complete. 26 cost towardssupplying and fitting skf n – 316 roller bearing (ford.e& nde side of the motor)and 6318 c & 6309 ball bearing, for de & de side of the pumpgrease, jute etc all complete 27 cost towardsrepairing of g.m shaft bush,neck ring,g.m impeller, tyre coupling set, gland titner,bearing housing for proper size making and machining and finishing for proper bearing fitting. 28 cost towardsrepairing & rewinding of 315 kva1/0.4 kv step down transformerreplacing burnt coil studs, transformer oil (300 lits.) insulator, lightening arrestor, with loading, unloading& transportation charge all complete. 29 cost towardsrepairing and overhaulingof 630 a vcb make abb taking out damaged spare parts then replacing by new one like ratchet assembly, flush mounting type triple pole, fixed contact, moving contact,arc shield motor and mountingtype of relay etc. all complete. 30 cost towardsrepairing of fasd starter 3 nos oil immersed star delta starter 2 no. replacing conductor, relay. timerand suitable contact finger 31 cost towards repairing and over hauling of 3 tonne chain pulley block, taken out its damaged spare parts then replacementby new one like chain pulley, stud nuts & bolts and gear all complete. 32 cost towardsrepairing and overhaulingof 400 a ocb make mei, taking out damaged spare parts then replacing with all complete 33 cost towards repairing of panel board replace by new one like mccb,cable, socket,washer, nuts & bolts, amp. meter, volt meter etc all complete. 34 cost towards s/f 90mm² x 3 core copper cable with isi mark. 35 (d) 2nd phase clear water sitarampur p/p. ( 100 h.p c/f pump set 3 nos )dismantling of100 h.pcentrifugal pump and taken out damaged impeller etc. all complete 36 cost towardsrepairing and rewinding of 100h.p sq. cage induction motor 3 phase, 50 cycles 1440 rpm 415 ± 10% volts with super enameled copper wire (34 kgs x 3) and replacing of spare materials like bearing nut bolts as per required with loading, unloadingtransportation charge all complete. 37 cost towardssupplying and fitting skf n – 316 roller bearing (ford.e& nde side of the motor)and 6309 & 6318 cball bearingfor de & de side of the pumpgrease, jute etc all complete 38 cost towardsrepairingof 6 dia n.r valve, sluice valve, 6 dia foot valve,suction pipe, bend, hydertaking out damaged spare partslike nut bolts, spindle, washer etcthen fitting by new one including the cost of machining turning & finishing all complete. 39 cost towardsrepairing of g.m shaft bush, . neck ring,g.m impeller, tyre coupling set, gland titner,bearing housing for proper size making and machining and finishing for proper bearing fitting. 40 cost towardsrepairing & rewinding of 250 kva1/0.4 kv step down transformerreplacing burnt coil studs, transformer oil (300 lits.) insulator, lightening arrestor, with loading, unloading& transportation charge all complete. 41 cost towardsrepairing and overhaulingof 630 a vcb make abb, taking out damaged spare parts then replacing by new one like ratchet assembly, flush mounting type triple pole, fixed contact, moving contact,arc shield motor and mountingtype of relay etc. all complete. 42 cost towardsrepairing of fasd starter 2 nos oil immersed star delta starter 1 no. replacing conductor, relay and suitable contact finger 43 cost towards repairing and over hauling of 3 tonne chain pulley block, taken out its damaged spare parts then replacementby new one like chain pulley, stud nuts & bolts and gear all complete. 44 cost towards repairing of panel board replace by new one like mccb, cable, socket,washer, nuts & bolts, amp. meter, volt meter etc all complete. 45 cost towards supplying and laying 300 mm² x 3½core pvc insulated armored aluminum cable 1.1 kv grade with isi mark 46 (e)bhua raw water p/p. (125 h.p.v.t pump set 3 nos ) repairing of 125 h.p,v.t 3 setsreplacing bowl assembly as per required along with loading, unloading & transportation charge all complete. 47 cost towardsrewinding of 125 h.p.v.t motor with suitable copper wire (42 kgs) and replacing of spare materials like bearing nut bolts as per required with loading, unloadingtransportation charge all complete. 48 cost towardssupplying and fitting thrust bearing skf 7320 for 60 h.p.v.t motor and proper greases etc. all complete 49 cost towardsrepairing & rewinding of 315 kva1/0.4 kv step down transformerreplacing burnt coil studs, transformer oil (300 lits.) insulator, lightening arrestor, with loading, unloading& transportation charge all complete. 50 cost towardsrepairing and overhaulingof 630 a vcb make abb, taking out damaged spare parts then replacementby new one like ratchet assembly, flush mounting type triple pole, fixed contact, moving contact,arc shield motor and mountingtype of relay etc. all complete. 51 cost towards repairing and over hauling of 3 tonne chain pulley block, taken out its damaged spare parts then replacementby new one like chain, stud nuts & bolts and gear all complete. 52 cost towardsmakingraw materials andsupplying and fittings.s line shaft size 56 mm x 72 long ofn 304 materials, g.m impeller for 3 stage 60 h.p.v.t pump as per size and sample, g.m bush, s.s line shaft , 8 dia m.s spider bearing with rubber cut less bush etc. all complete 53 cost towardsrepairingof 8 dia n.r valve, sluice valve,suction pipe, bend, hydertaking out damaged spare partslike nut bolts, spindle, washer etcthen fitting by new one including the cost of machining turning & finishing all complete. 54 cost towards repairing of panel board replace by new one like mccb, cable, socket,washer, nuts & bolts, amp. meter, volt meter etc all complete. 55 (f) gamharia pani tanki p/p, ( 40 h.p c/f pump set 2 nos ) dismantling of the 40 h.p 2 sets, induction motorfrom foundation headand taken out rotor from stator etc. all complete 56 cost towardsrewinding of40 h.p 2 sets,inductionmotor with suitable copper wire (24 x 2 kgs) and replacing of spare materials like bearing nut bolts as per required with loading, unloadingtransportation charge all complete 57 cost towardsrepairingof 4 dia n.r valve, sluice valve, 6 dia foot valve,suction pipe, bend, hydertaking out damaged spare partslike nut bolts, spindle, washer etcthen fitting by new one including the cost of machining turning & finishing all complete. 58 cost towardsrepairing and replacement of g.m shaft bush,neck ring,g.m impeller, tyre coupling set, gland tightner, bearing housing for proper size making and machining and finishing for proper bearing fitting. 59 cost towardssupplying and fitting skf 6306 ball bearing (ford.e& nde side of the motor)and ball bearing, greases, jute etc all complete 60 cost towards repairing and over hauling of 2 tonne chain pulley block, taken out its damaged spare parts then replacementby new one like chain pulley, stud nuts & bolts and gear all complete. 61 cost towardsrepairing of fasd starter 2 nos replacing conductor, relay and suitable contact finger 62 cost towards repairing of panel board replace by new one like mccb, cable, socket,washer, nuts & bolts, amp. meter, volt meter etc all complete. 63 (g) s/f consumable materials like grease, gland packing, jute, diesel etc. with replacing lighting equipments like bulb, holder, fuse wire human safety equipments like safety shoes, safety gloves, goggles, aparanmats etc. all complete ( for 1st & 2nd phase c/w and 1st & 2nd phase r/w) ...
37557398 bids are invited for procurement of combined thrust bearing & guide bearing coolers (heat exchangers) of unit# 1. at phps, (q3) total quantity : 3...
37406346 e quotation for seeking firm rates for non schedule items for preparing estimates of annual repair and maintenance of water supply system and sanitation t rinpas, kanke, ranchi under d.w and s mechanical division, ranchi. , cost towards providing all labours tools & techniciansfor dismantling and disconnecting of 40 hp kirloskar make motor and taken out rotor from motor stator cutting removing burnt and damaged coil and after repairing refitting the same etc all complete. , cost towards full rewinding of 40 hp motor stator with supplying of super enameled round copper conductor suitable gauge class f insulating materials making all connection taping, varnishing with dr beck varnish all complete with deducting the cost of taken out scrap materials ( wt. of wire is 18.5kg approx ) . , s / f ball bearing skf make 6312&6309 at de&nde side of 40 hp kirloskar make motor including proper greasing all complete. , cost towards providing all labour tools and tackles for dismantling of 40 hp single stage kirloskar make c / f pump with changing damaged parts such as gm neck ring as per size and sample 2 nos. shaft sleeve 2 nos. shaft sleeve check nut 2 nos. making ci bearing housing as per size and sample 2 nos. supplying and fitting ball wearing skf make 6309 2nos. making supplying and fitting ms gland tightner as per size and sample 2 pair making citric motion of rotating unit assembling on lathe m / c etc all complete , cost towards repairing of 40 hp l&t motor starter by supplying and fitting l&t make 3 core ml 4 power contactor 45 amp. with auxiliary contractor complete set 2nos. supplying and fitting timer type lt 100 1nos., over load relay suitable range 1nos.etc all complete. , cost towards providing all labours tools & technicians for taking out damaged 250amp. tpn hrc fuse type disconnector main switch replacing new disconnector fuse unit with hrc fuse 1 set doing electrical connection and testing on full load after deducting the cost of taken out scrap materials , supplying and fitting 6”dia tyre coupling complete set with nut bolt washer and tyre of reputed make for 40 hp pump set. , cost towards providing all labour tools and tackles for dismantling and taken out damaged nr valve and s / f 4”dia c.i df nr valve heavy duty rating pn 1 isi marked on delivery pipe line with all work including cost of labour charge all complete testing on full load with deducting the cost of scrap materials. , cost towards supplying and laying 50 mm² x 3.5 core aluminium armoured cable from main switch to industrial panel. ( both sets ) . , cost towards supplying and laying 16 mm² x 3 core copper cable from panel to starter and starter to motor in bunch of two. ( both sets ) . , cost towards replacing damaged suction pipe by making supply & fitting 100 mm dia heavy duty m.s. suction pipe 10feet long both and 100 mm dia m.s. flange welding, 100mm dia long bend 1 no with nut bolt rubber insertion etc required for the job. , transportation charge of above p / set from work site to work shop and vice versa including loading and unloading charge. , cost towards dismantling of 100 hp wpil make single stage c / f pump and taking out its rotating unit assembly with changing of damaged parts by new making s / f neck ring as per sample size 2 nos, c.i shaft sleeve as per sample size – 2nos, making s / f shaft sleeve check nut as per sample size – 2 nos , s / fball bearing skf 6309 2 nos and repairing of bearinghousing by welding turning machining as per bearing size 2 nos, c.i gland tightner as per sample size – 2nos including cost of reassembling of rotating unit assembly balancing rotating unit assembly and fitting the pump with supply of grease gland packing oil packing paper with transporting cost of rotating unit from p / plant to workshop and back , cost toward supplying fitting & changing of 100 hp jyoti make motor ball bearing skf 6316 at de side 1 no. and sk 6314 nde 1 no. with grease. , cost towards repairing of 100 hp l & t make f.a.s.d starter with s / f contactor set 2 sets ) , relay unit ( 85 135a ) 1set, timer unit 1 set, making new connection etc all complete. , supplying and fitting 6”dia tyre coupling complete set with nut bolt washer and tyre of reputed make for 100 hp pump set. , cost towards supplying and fitting mccb 630 amp. for bus bar make l&t schneider / bch , cost towards supplying and fitting mccb 250 amp. for bus bar make l&t schneider / bch , cost toward supplying fitting & changing 100mm dia cidf sluice valve ( pn 1 ) 1 set & cidf nr valve ( pn 1 ) 1 no. including fitting charge , cost toward supplying fitting & changing 150 mm dia ci foot valve hiding single leather flat and gun metal seating all complete. , submersible pump sets , cost towards providing all labour tools and technicians for dismantling and taken out 5hp submersible p / set with column pipe for bore well. , cost towards repairing of5 hp submersible pump with s / f norylimpeller as per size and sample, diffuser, s.s. shaft, s.s. coupling, s.s. sleeve, nut, c.i. suction casing, c.i nrv etc. all complete ( 23 stage ) after the deduction of cost of scrape materials. , cost towards for rewinding and repairing of5 hp submersible motor with s / f 1.2 swg round copper winding wire 24 slot, gun metal bush, thrust plate, thrust bearing, diapharm, oil seal, etc with lathe work. all complete. after the deduction of cost of scrape materials. , supplying all material such as 40 mm dia g.i. pipe medium quality 15 ft. long, charcoal salt etc. for making earthing station as per i.e. rule , cost towards replacement of old and damaged underground service line by supplying new overhead line 10 mm² 3core copper wire after the deduction of cost of scrap materials. , supplying and laying ( under and over ground ) 2 dia aqua gold weather proof pvc pipe from bore well to main rising pipe line ( damaged pipe replacement ) make supreme / isi mark ( both sets ) , supplying and laying ground and on wall 10 swg, g.i. wire for doing continuous earthing for all electrical equipments , cost towards s / f and changing of 2”dia upvc column pipe with heavy duty socket ( make supreme / paras ) for both sets. , cost towards replacement of damaged submersible cable by supplying and fitting 4 mm2x 3 core flat submersible cable including cable jointing all complete. after the deduction of cost of scrape materials. , providing all labour, tools tackles& technicians for lowering of 5hp submersible pump set with all accessories in the bore well , cost towards supplying and fitting ( 1 ) 50 mm dia g.m. full way valve – 1 no ( 2 ) 40 mm dia nr valve – 1 no ( 3 ) 40 mm dia g.i. bend ( 4 ) 2” dia m.s. clamp with nut bolt 2 pair after the deduction of cost of scrape , supplying and installation suitable size panel board for 5 hp submersible pump including fixing on wall comprising of following points such as ( 1 ) d.o.l starter 1no. ( 2 ) hrc fuse – 3 no. ( 3 ) voltmeter with selector switch – 1 set ( 4 ) ammeter with selector switch – 1 set ( 5 ) phase indicating neon lamp – 3 nos. etc. all complete after the deduction of cost of scrap materials. , supplying and fitting union 1.5 dia , supplying and fitting elbow 1.5 dia , supplying and fittingtee 1.5 dia , supplying and fitting socket 1.5 dia , supplying and fitting upvc valve 1.5 dia , transportation charge of above p / set from work site to work shop and vice versa including loading and unloading charge....
37386516 bids are invited for diamond core drilling accessories mse hq core lifter , hq shut off valve , hq core case , nq landing ring , hq landing ring , hq centralizer , t 8 thrust bearing , t 6 thrust bearing , t 10 bearing , t 113 bearing , nq lifting dog , nq latches with spring , 51115 thrust bearing , 6309 ball bearing , 3210 ball bearing , 51113 thrust bearing , 51211 thrust bearing , 25k hi tech water swivel wash pipe , 25k hi tech water swivel packing , crelious water swivel wash pipe , crelious water swivel packing , nq shut off valve , nq centralizer , nq guide and locking coupling , hq guide and locking coupling total quantity : 420...
37326781 e quotation for seeking firm rates for non schedule items for preparing estimates.annual repair and maintenance of water supply system and sanitation at t.b. sanatorium itki under d.w. & s. mechanical division ranchi. annual repair and maintenance of water supply system and sanitation at t.b. sanatorium itki under d.w. and s. mechanical division ranchi. , provision leake repairing of different and size of upvc sch 80 pipe in place of existing / cracked and damaged pipe of isi approved make or equivalent make damaged pipe in trenchage and replacement of pipe and fitting so as to give. i m average cover over the socket of pipes with disposal of excavated earth within initial lead and lift and necessary fitting and earth work in backfilling and cutting pipe to size etc. all complete as per specification and direction of e / i. , leakage in 50 mm dia upvc pipe , leakage in 40 mm dia upvc pipe , leakage in 32 mm dia upvc pipe , leakage in 25 mm dia upvc pipe , leakage in 20 mm dia upvc pipe , provision leake repairing of different and size of upvc sch 80 pipe in place of existing / cracked and damaged pipe with red lead and yarn of following nominal bore screwed and socketed joints on wall, ceiling and floor including supplying and fitting on wall hooks or pipe clamp wooden plugs, cutting pipe to size and threading ends where necessary etc. all complete as per specification and direction of e / i. , leakage in 50 mm dia upvc pipe , leakage in 40 mm dia upvc pipe , leakage in 32 mm dia upvc pipe , leakage in 25 mm dia upvc pipe , leakage in 20 mm dia upvc pipe , supplying and flaxing u pvc ball valve of approved make all complete as per direction of e / i. , 50 mm dia u pvc ball valve , 40 mm dia u pvc ball valve , 32 mm dia u pvc ball valve , 25 mm dia u pvc ball valve , 20 mm dia u pvc ball valve , supplying of materials for c.p. bathroom fitting ( as per schedule rate ) to consumrtion day to day work. , 15mm dia c.p. bib cock ( long thread ) , 15mm dia c.p. pillar cock ( long thread ) , 15mm dia c.p. angular stop cock ( long thread ) , 15mm dia cp basin mixture , 15mm dia cp wall mixture , jet sprey , health faucet , bib cock spindle , a ) medium size , b ) large size , mirror , towel rail , soap dish , 32mm dia cp waste : , 32mm dia pvc waste pipe 750mm long with coupling : , 100mm dia c.p. jali : , 15mm dia and 45cm long pvc connection pipe : , sink waste , cistern ball cock , cistern handle , pvc water storage tank cover ( 2000 / 1000 l ) , 25mm dia ball cock set for pvc tank , cammod cover , m seal , waste pipe bundla , 10 lit pvc l / d cistern , flush bend , basin , supplying, fitting and fixing pvc pipes of approved make including supplying nails, clips and pvc washer cement & yarn for making plumber joints properly cutting pipe to sizes including earth work of scaffolding etc. where necessary etc. all complete as per specification and direction of e / i. , 100mm dia pvc sewer pipe , 75mm dia pvc sewer pipe , supplying and fixing pvc fitting of approved make confirming to isi including supplying nails and bobbins from making solvent cement solution or gasket joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of e / i. , 110mm swr nahani trap , 110mm swr plain bend , 110mm swr door bend , 110mm swr plain tee , 110mm swr door tee , 75mm swr plain bend , 75mm swr door bend , 75mm swr plain tee , 75mm swr door tee , supplying all materials , labours, tools and equipment for laying upvc pipesof approved make in trenches with upvc solvent solution with socket and screw joints and cutting pipe as per size and threading ends where necessary etc. all complete as per specification and direction of e / i. ( in trenches ) , 50mm dia. upvc schedule 80 pipe ( in trenches ) [ make supreme / ashirwad / paras ] , 25mm dia. upvc schedule 80 pipe ( in trenches ) [ make supreme / ashirwad / paras ] , 40mm dia. upvc schedule 80 pipe ( in wall&overground ) [ make supreme / ashirwad / paras ] , supplying and fixing upvc fittings of approved make all complete as per specification and direction of e / i. , a ) upvc elbow ( 90 degree ) 50mm dia. upvc , 40mm dia upvc , 25mm dia upvc , b ) tee plain 50mm dia. upvc , 40mm dia upvc , 25mm dia upvc , c ) reducing bush 50mm x 25mm dia. upvc. , 50mm x 40mm dia upvc , 40mm x 25mm dia upvc , d ) reducing tee 50mm x 25mm dia. upvc. , 40mm dia upvc , 25mm dia upvc , e ) upvc socket 50mm dia. upvc , 40mm dia. upvc , 25mm dia upvc , f ) union socket ( upvc ) 50mm dia. upvc , 40mm dia upvc , 25mm dia upvc , providing all material, equipment and wash out and cleaning of 2000 / 1000 litre pvc water storage tank including rubbing the wall of tank by the help of coconut, rushi and bleaching powder their washing by clean water all complete as per direction of e / i. , 3000 litre capacity hdpe w / s / tank 2 time x 3000 liter x 2 nos. = 12000.00 liter 2000 litre capacity hdpe w / s / tank 2 time x 2000 liter x 88 nos. = 372000.00 liter 1000 litre capacity hdpe w / s / tank 2 time x 1000 liter x 9 nos. = 18000.00 liter total = 402000.00 liter , 10 hp c / f pump set , cost for complete rewinding of 10 h.p sq. cage induction motor operated on 415v, 3 phase, 50 c / s 1460 rpm with supply fitting of super enameled copper wire and other required insulation materials, heating assembly of the motor and testing on load ( wt of burnt coil 5.5 kg ) , cost for dismantling of 10 h.p c / f pump checking and changing of its damaged parts such as pump shaft of en 9 materials 01 no. key 02 nos. gland tightner 2 sets, gland tightner stud 4 nos. c.i bearing housing with cap 2 sets, ball bearing 6306 ( skf ) 2 nos. casing stud 16 mm sq. x 80 mm long with nut 8 nos. packing paper. grease, gland packing etc all complete and testing on load. , cost for supply and fitting of 3 dia tyre coupling complete set with nut, bolt & tyre. all complete. , cost for supply and fitting of 4 dia g.m flap tyre foot valve with packing and nut & bolt 4 nos. etc all complete. , cost for supply and fitting of 3 dia cidf heavy duty sluice valve, isi marked , cost for overhauling and repairing of motor control panel and changing of its damaged parts such as contactor ( ml 4 ) 3 nos., vm 02 nos., am 01, selector switch 2 nos, 100 amp mccb – 1 no, etc all complete and testing on load. , 3 h.p. submersible p / set , providing all labour, tools, tackles and technicians for taking out 3 h.p. submersible pump set with column pipe for bore well , cost towards for rewinding and repairing of 3 h.p submersible motor with s / f suitable winding wire, bronze bush etc. all complete after the deduction of cost of scrape materials. , cost towards repairing of 3 h.p. submersible pump with s / f bronze impeller as per size and sample, bush, thrust plate, pump shaft etc. all complete after the deduction of cost of scrape materials. , cost towards replacement of damaged submersible cable by supplying and fitting 2.5 mm2x 3 core flat submersible cable including cable jointing all complete for both set. after the deduction of cost of scrape materials. , cost towards supplying fitting, changing 2” dia g.i. column pipe with heavy duty socket ( make zindal / tata ) after the deduction of cost of scrape materials. , cost towards supplying and fitting ( 1 ) 2 dia g.m. full way valve – 1 no ( 2 ) 2 dia nr valve – 1 no ( 3 ) 2 dia g.i. bend 2 nos. ( 4 ) 2” dia m.s. clamp with nut bolt 2 pair after the deduction of cost of scrape materials. , providing all labour, tools tackles and technicians for lowering of 3 h.p submersible pump set with all accessories in the bore well , 5 h.p. / 7.5 h.p. submersible p / set , providing all labour, tools, tackles and technicians for taking out 5 h.p. submersible pump set with column pipe ( 280 ) from bore well , cost towards for rewinding and repairing of5 hp submersible motor with s / f 1.0 swg round copper winding wire 24 slot, gun metal bush, thrust plate, thrust bearing, diapharm, oil seal, etc with lathe work. all complete. after the deduction of cost of scrape materials. , cost towards repairing of 5 hp submersible pump with s / f noryl impeller as per size and sample, diffuser, s.s. shaft, s.s. coupling, s.s. sleeve, nut, c.i nrv etc. all complete ( 23 stage ) after the deduction of cost of scrape materials. , cost towards replacement of damaged submersible cable by supplying and fitting 4 mm2x 3 core flat submersible cable including cable jointing all complete. after the deduction of cost of scrape materials. , cost towards supplying fitting, changing 2” dia g.i. column pipe with heavy duty socket ( make zindal / tata ) after the deduction of cost of scrape materials. , cost towards supplying and fitting ( 1 ) 50 mm dia g.m. full way valve – 2 no ( 2 ) 50 mm dia nr valve – 1 no ( 3 ) 50 mm dia g.i. bend ( 4 ) 2” dia m.s. clamp with nut bolt – 2 pair after the deduction of cost of scrape materials. , supplying and laying ground and on wall 10 swg, g.i. wire for doing continuous earthing for all electrical equipments , providing all labour, tools tackles and technicians for lowering ( 280 ) of 5 h.p.submersible pump set with all accessories in the bore well , supplying and installation suitable size panel board for 5 h.p. submersible pump including fixing on wall comparising of following points such as ( 1 ) d.o.l starter – 1 no. ( 2 ) hrc fuse – 3 no. ( 3 ) volt meter with selector witch 1 set ( 4 ) ammeter with selection switch – 1 set ( 5 ) zindicating neon lamp – 3 no. etc. all complete after the deduction of cost of scrape materials....
35902032 bids are invited for bearing parts accessories mse nq overshot latch with spring , nq inner tube latch with spring , t 8 bearing , t 6 bearing , ball bearing 6309 , thrust bearing 51115 , wash pipe 81mm , water swivel packing 81mm , rubber bucket 76mm , nq landing ring total quantity : 144...
35593182 bids are invited for hq core lifter and core case mse adopter hq pin to nq box , hq shut off valve , hq core case , nq landing ring , hq corelifter , thrust tapered roller bearin no t 113 , t 8 thrust bearing , t 6 thrust bearing total quantity : 72...
35489091 e quotation for electro mechanical components by supplying and fitting and replacing of electro mechanical components of baharagora multi village rural water supply scheme 1 boosting p/plant w.t.pat mohanpur of bahragoda rwss cost towards supply installation and testing and commissioning of horizontal split casing type centrifugal pump make mather &platt/kirloskar /wpil capable of discharhing 100 m³/hr clear water against total head 30 meters, coupled with suitable 3 phase. 1440 rpm, 50hz tefc sq. cage induction motor make kirloskar, cgl/abb mounted on a common m.s. channel fabricated base plate with following accessories 1. sutable size n.r valve1 no2. sutable size sluice valve 1 no3. sutable size check valve/foot valve1 no4. pressure gauge1 no5. m.s base plate 1 no6. tyre coupling set 1 noetc all complete. 2 cost towards dismantling of old foundation and removing the residuals out of the pumping plant and making of new pcc foundation 4’x3’ x2.5’ size & m.s joint 4”x6” 2 nos. with supplying all mortar materials & foundation bolts 6 nos. with all labour tools and tackles loading unloading with alignment leveling and jointing as per p.w.d specification (1:2:4) etc all complete. 3 cost towards supplying installation & commissioning of 160 amp, 440 vmotor panel board made of 2mm thick ms sheet of suitable size, dust and vermin proof consisting of following accesories :(i)160 amp mccb – 1 no.(incoming feeder) (ii)100 amp mccb – 02nos (outgoing feeder). (iii)32 amp mcb 1 no. for lighting load and other utiliti load.(iv)fasd starter suitable for the 12.5 hp motor pumpset – 2 nos.(l&t make)(v)copper bus bar 4 pole 160 amp 415volt copper strip bus bar enclosed in ms sheet, etc. all complete job. (vi)led display voltmeter – (0 500 v) & amp meter(0 100a) – 2 sets, phase indicating lamp 6 nos.along with overload relay, single phase preventer proper inside wiring with suitable size of copper conductor with wall/floor mounting facility, cubical panel box etc. all complete including transportation and fitting and mounting charges at p/plant. 4 cost towards repairingof 63 kva transformer with changing of ht & lt bush 3 sets each , top up transformer oil upto 100 ltrs, fuse wires as per required. 5 cost towards supplying and laying of 3core 95 sq.mm aluminium armoured cable from transformer to mcp 6 cost towards chemical earthing 40feet and 80mm hole size with electrode and chemical compound etc. with watering pipe and locking arrangements including soldering, riveting, jointing g.i. flat strip 20mm x 3mm to all equipments. 7 cost towards supplying and installing 100 watt led street light complete set all complete including labour charges. for clear water p/plant. 8 cost towards supplying installation and commissioning of 63 kva servo controlled (oil cooled) automatic voltage stabilizer suitable for output voltage of 415 + 1% 3 phase, 50 hz with copper wound transformer as mentioned below. the stabilizer shall function satisfactorily even if incoming supply is unbalanced between phases within range of 10%.the stabilizer should be constructed in cubical box,with bidirectional wheels for easy handling necessary monitors and user’s controls on front panel such as inducation alarm, voltmeter and selector switch for measuring input and output voltage auto manual selector switch.raise low push buttons etc. suitable capacity termination strips and bus bars for incoming and outgoing cable should be provided .all three phases shall be independently monitored and corrected following protections and indication shall be incorporated as per is:9815a) over voltage/under voltageb)single phasing c) cut off contactorwith electronic output sensing unit d) suitable change over switch and earthing 100 kva oil cooled servo controlled automatic voltage stabilizer (output 415 unit+ 1%) input 280 to 450 volt. make: powerline/servokon 9 cost towards of changeover switch tpn on load with sheet sheel enclosure capacity amp for by pass arrangement of servo voltage stabilizer make c&s havell s/l&t with all labour & tools and materials. 10 supplying and laying of 25 sq.mmx3core x1.1 kv grade with isi make pvc insulated and unarmored flexible copper cable from mcp to motor terminal box with suitable copper lugs etc 11 part –braw water pumping plant – intake well at jamsola providing all labours, tools, tackels and technician fordisconnection and taking out20 hp vt p/set with column pipe into intake well all complete. 12 cost towards all labour, tools, tackles and technicianfor opening, dismantling. repairing and overhauling of20 hp 04 stage bow l assembly vt pump having head58 meter. discharge 43m3/hr speed 1460 rpmi. with s/f of s.s. pump shaft 01 no.ii. top and bottom bush 02 nos.,iii. intermediate bushes 5 nos.iv. spider cut less rubber bushes 04 nos.v. locks vi. impeller copper bush 06 pcs.vii. g.m. impeller 04 nos. viii. 30mm dias.s. line shaft 10 ft each 3 nos.ix. 30mm dia. ss.head shaft 5 ft. each i nos.x s. s socket and bush 04 nos. each. xi, ferro collar ball rubber bush 12pc xii. ball sleeve bush 07 nos each all materials as per required reassembling the same at workshop refitting at site etc. all complete(rate after deducting the scrap materials). 13 providing all labours, tools, tackels and technician forloweringafter repairing of20 hp vt p/set with column pipe into intake well all complete. 14 cost towards supplying all labour tools and tackles for complete opening, dismantling. of 20 hp 440 volt,50c/s, star delta, 3phase vt motor by supplying supperenameled copperwireandthentapping,varnishing, heating & testing on lull load and repairing of stator and rotor with including the deduction of cost of burnt copper wire approx. 18.5 kg.with changing of following bearing: (i) ball bearing as per sample 01 no. and (ii) thrust bearing as per sample (skf make) at raw water p/plant. 15 cost towards transportation charges of above pump motor set and other linings materials from p/plant to workshop and vice versa. 16 supplying and laying of 25 sq. mm x 3 core x 1.1 kv grade with isi mark pvc insulated and unarmoured flexible copper cable from mcp to motor terminal box with suitable copper thumble socket etc. 17 s/f of 90 watt ledfloodlighting luminaire with pressure die cast housing and toughened glass cover, operating voltage range 100v 270v ac with structure,stand, clamp, tee, wires and switches etc. all completeincluding repairing of lighting arrangements inside and outside of pump house at raw water p/plant. 18 costtowardssupplying andfitting of lighteningarrester suitable for building protection with earthingelectrode ,earthing compound, copper wires and earth work etc. all complete job. 19 cost towards replacement of old panel by supply installation & commissioning of new standing type floor mounting industrial panel board comprising 200 amp copper bus bar nos. in m.s steel(14swg) housing.•200 amp t.p.n mccb make l&t as incomer feeder.• 100 amp t.p.n mccb make l&t 2 nos as outgoing feeder.• ammeter digital ammeter with selector switch l&t/c&s make• voltmeter degital voltmeter in 3 phase ryb• indicating lamp led l&t/siemens/c&s make in red, yellow and blue colour 1 set.• 32 amp mcb for light load and other loads of l&t /havel’s/c&s make (2 no.)• fasd starter (make l&t) suitable for above pump set. panel should be dully painted with two coats super enameled paint of approved color one coat of red oxide primer and internally wired with suitable size of copper wire etc. all complete. 20 cost towards supplying triple spur gear type chain pully block of 3 tonne capacity with 6m lift complete with load chain and hand chain suitable for above lift, tested to 50%over load as per is 3832 carrying isi mark with travelling trolley etc. 21 cost towards of changeover switch tpn on load with sheet sheel enclosure capacity amp for by pass arrangement of servo voltage stabilizer make c&s havell s/l&t with all labour & tools and materials. 22 cost towards supplying and laying of 3core 95 sq.mm aluminium armoured cable from transformer to mcp 23 cost towards supplying installation and commissioning of 63 kva servo controlled (oil cooled) automatic voltage stabilizer suitable for output voltage of 415 + 1% 3 phase, 50 hz with copper wound transformer as mentioned below. the stabilizer shall function satisfactorily even if incoming supply is unbalanced between phases within range of 10%.the stabilizer should be constructed in cubical box,with bidirectional wheels for easy handling necessary monitors and user’s controls on front panel such as inducation alarm, voltmeter and selector switch for measuring input and output voltage auto manual selector switch.raise low push buttons etc. suitable capacity termination strips and bus bars for incoming and outgoing cable should be provided .all three phases shall be independently monitored and corrected following protections and indication shall be incorporated as per is:9815a) over voltage/under voltageb)single phasing c) cut off contactorwith electronic output sensing unit d) suitable change over switch and earthing 100 kva oil cooled servo controlled automatic voltage stabilizer (output 415 unit+ 1%) input 280 to 450 volt. make: powerline/servokon ...
35003592 procurement of wpil make pumps spares on non rc basis installed in ntpcnkstpp off site area. , vo swp 100 / 450: pp impeller nut , vo swp 100 / 450: pp cooling tube , vo swp 100 / 450: pump shaft sleeve , vo swp 100 / 450: stuffing box bush , vo swp 100 / 450: head shaft bush , vo swp 100 / 450: packing box , vo swp 100 / 450: thrust bearing assy , vo swp 100 / 450: pin bush type coupling , vo swp 100 / 450: line shaft bush , vo swp 100 / 450: line shaft sleeve , vo swp 100 / 450: split ring , vo swp 100 / 450: pump gland , vo swp 100 / 450: bottom column pipe , vo swp 100 / 450:intermediate column pipe , vo swp 100 / 450: top column pipe , vo swp 100 / 450: top discharge pipe , vo swp 100 / 450:intermediate disch. pipe , vo swp 100 / 450: delivery bend , vo swp 100 / 450: pp casing , vo swp 100 / 450: head shaft sleeve , vo swp 100 / 450: shaft coupling , impeller nut, wpil, vo wpes 100 / 400 , cooling tube, wpil, vo wpes 100 / 400 , pump shaft sleeve, wpil, vo wpes 100 / 400 , stuffing box bush, wpil, vo wpes 100 / 400 , head shaft bush, wpil, vo wpes 100 / 400 , packing box, wpil, vo wpes 100 / 400 , bearing housing, wpil, vo wpes 100 / 400 , pin bsh cplng, wpil, vo wpes 100 / 400 , line shaft bush, wpil, vo wpes 100 / 400 , line shaft sleeve, wpil, vo wpes 100 / 400 , split ring, wpil, vo wpes 100 / 400 , pump gland, wpil, vo wpes 100 / 400 , bottom column pipe, wpil, vo wpes 100 / 400 , int column pipe, wpil, vo wpes 100 / 400 , top column pipe, wpil, vo wpes 100 / 400 , top discharge pipe, wpil, vo wpes 100 / 400 , int disch pipe, wpil, vo wpes 100 / 400 , delivery bend, wpil, vo wpes 100 / 400 , pump casing, wpil, vo wpes 100 / 400 , head shaft sleeve, wpil, vo wpes 100 / 400 , shaft coupling, wpil, vo wpes 100 / 400 , vo 10 mn 12: pp impeller nut , vo 10 mn 12: pp cooling tube , vo 10 mn 12: pump shaft sleeve , stfng box bsh, wpil, vo 10 mn 12 , hd shft bsh, wpil, vo 10 mn 12 , pckng box, wpil, vo 10 mn 12 , brg hsng assy, wpil, vo 10 mn 12 , pin bsh cplng, wpil, vo 10 mn 12 , line shft bush, wpil, vo 10 mn 12 , line shft sleeve, wpil, vo 10 mn 12 , split ring, wpil, vo 10 mn 12 , gland, wpil, vo 10 mn 12 , vo 10 mn 12: bottom column pipe , int clmn pipe, wpil, vo 10 mn 12 , top clmn pipe, wpil, vo 10 mn 12 , vo 10 mn 12: top discharge pipe , int disch pipe, wpil, vo 10 mn 12 , vo 10 mn 12: delivery bend , vo 10 mn 12: pp casing , hd shft sleeve, wpil, vo 10 mn 12 , shft cplng, wpil, vo 10 mn 12 , impeller nut, wpil, vo wpes 25 200 , pump shaft sleeve, wpil, vo wpes 25 200 , stuffing box bush, wpil, vo wpes 25 200 , stuffing box, wpil, vo wpes 25 200 , head shaft sleeve, wpil, vo wpes 25 200 , head shaft bush, wpil, vo wpes 25 200 , packing box, wpil, vo wpes 25 200 , bearing housing, wpil, vo wpes 25 200 , pin bsh cplng, wpil, vo wpes 25 200 , split ring, wpil, vo wpes 25 200 , impeller, wpil, vo wpes 25 200 , casing, wpil, vo wpes 25 200 => limited...
34894401 annual rate contract for supply of bearings annual rate contract for supply of bearings of make schaeffler / skf / timken / ntn as per tender documents , ball bearings , ball bearings 308n, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 607, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 608, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6000, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6001, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6002, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6005 2rsr, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6006, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6006n, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6007, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6008a etn9, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6009, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6010, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6011, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6012, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6013, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6014, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6015, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6017, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6020, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6022, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6024, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6026, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6200, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6201, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6201 zcxcx, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6202, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6203, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6204, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6205, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6206, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6207, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6208, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6209, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6210, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6211, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6212, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6213, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6214, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6215, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6216, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6217, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6218, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6219, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6220, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6221, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6222, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6224, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6226, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6228, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6230, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6302, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6303 lha, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6304, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6305, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6306, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6307, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6308, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6309, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6310, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6311, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6312, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6313, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6314, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6315, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6316, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6317, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6318, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6319, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6320, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6321, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6322, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6324, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6326, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6321mc3, brass cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6322mc3, brass cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6326mc3, brass cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6330 / c3, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6404, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6405, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6406, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6407, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6408, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6409, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6410, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6411, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6412, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6413, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6414, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 61832, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 61836, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6005 ma.c3 , brass cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6204 ma.c3 , brass cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6304 ma.c3 , brass cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6000 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6001zz, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6009 / zc3, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6003 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6004 2z , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6007 2z , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6008 2z , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6012 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6200 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6201 2zr, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6202 2z , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6203 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6204 2z , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6205 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6206 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6207 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6208 2z , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6209 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6210 2z , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6211 / 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6211 / 2zr / c3, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6212 / z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6212 / 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6213 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6215 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 625 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6301 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6302 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6304 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6305 2z , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6306 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6306 z.c3 , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6307 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6308 2zr, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6309 2z , steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6310 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6311 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6312 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6313 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6313 2rs1, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6314 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6315 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6316 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6317 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6318 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6319 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6322 / 2z, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 6803 c3, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 61826 2rsi, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 63082rfi, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 62201rsi, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 61901, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 4204 atn9, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings qj 314 n2ma / c2l ( 4 point ball bearing ) , metallic cage, make: schaeffler ( fag ) / skf / timken , ball bearings qj 315 n2ma ( 4 point ball bearing ) , metallic cage, make: schaeffler ( fag ) / skf / timken , ball bearings qj309tvp.c3 ( 4 point ball bearing ) , metallic / polymide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3204, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3205, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3208, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3302 b tnh, polymide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3305, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3306, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3307, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3308, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3309, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3310, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3311, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3312, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 3313, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1208k , polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1209k , polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1210, polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1211k , polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1212k , polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1213k , polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1215, polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1215k , polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1217, polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1217k , polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1218k , polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1309k , polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1310, polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1315k, polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 1317k, polyamide cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2207, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2208, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2215, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2312, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2220k, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2213k, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2211k, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2212k, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2217k, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 2218k, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7212, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7216, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7217, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7307, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7309, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7309b, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7310, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7312, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7313, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7322, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7320, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7205, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7206, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7306, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 7322, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 16005, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 16007, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 16009, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 16010, steel cage, make: schaeffler ( fag ) / skf / timken , ball bearings 16012, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51101, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51102, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51103, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51104, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51107, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51108, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51202, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51203, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51204, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51205, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51206, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51208, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51209, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51210, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51214, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51103, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51105, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51202, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51206, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51306, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51310, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 51411, steel cage, make: schaeffler ( fag ) / skf / timken , thrust bearing 53310, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 21309, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 21313, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 21314, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22206, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing urb 22207, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22208, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22209, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22210, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22211, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22212, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22213, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22214, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22215, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22216, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22217, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22218, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22219, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22220, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22222, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22224, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22226, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22228, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22230, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22230cc / w33, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22232, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22234, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22236, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22240 ck / w33, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22256, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22308, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22309, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22310, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22311, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22312, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22313, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22314, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22315, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22316, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22317, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22318, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22318, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22318 vibration duty & brass cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22319, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22319 vibration duty & brass cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22320, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22322, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22322 vibration duty & brass cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22324, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22326, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22326 vibration duty & brass cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22328, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22330, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22332, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22332 vibration duty & brass cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22334, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22336, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22340, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 22344, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23024, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23036, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23040, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23044, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23052, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23122, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23126, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23132, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23134, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23136k, brass cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23138, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23140, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23144, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23152, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23218, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23220, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23222 cck / w33, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23224, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23230, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23330, metalliccage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23244, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 23984, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 29328, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 24032 cc / w33, steel cage, make: schaeffler ( fag ) / skf / timken , spherical roller bearing 24172ecck / w33, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nh 207, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing n215, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing n 305 ecp, polymide cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj217, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing n218, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing n305, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing n308, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing n310, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing n312, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing n318, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing n322, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj 207 e, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj208 zkl, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj209, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj 307 e, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj308, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj 309 e, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj312, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj2214, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj2220, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj2305, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj2306, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj2309, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj2312, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj2320, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj305, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nj406, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing m30 6 / nj406, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu1012, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu 308em, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu205, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu207, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu208, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu210, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu213, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu214, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu215, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu216, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu218, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu219, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu221 , metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu224, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu226, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu2226, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu232, brass cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu 2204 ecp, polymide, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu2305, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu2308, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu 2309, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu2317, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu2334, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu305, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu309, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu310, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu312, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu313, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu314, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu315, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu316, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu317, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu318, metalliccage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu319, brass cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu320, brass cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu321, brass cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu322, brass cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu324, brass cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu326, brass cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu 328, brass cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nu410c3, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nup206ecp, polymide cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nup214, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nup313, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nup2213, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nup2313, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nup2317, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing nup313, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing sl18 1838 br / equivalent, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing sl18 1844 br / equivalent, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing sl18 1852 br / equivalent, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing sl18 1860 br / equivalent, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing ina rnn f 238902 v br / equivalent, steel cage, make: schaeffler ( fag ) / skf / timken , cylindrical roller bearing rnn f 238540 v br / equivalent, steel cage, make: schaeffler ( fag ) / skf / timken , needle roller bearing hk 4016, steel cage, make: schaeffler ( fag ) / skf / timken , needle roller bearing nk18 / 20, steel cage, make: schaeffler ( fag ) / skf / timken , needle roller bearing nki22 / 16, steel cage, make: schaeffler ( fag ) / skf / timken , unit bearing ucf207, make: schaeffler ( fag ) / skf / timken , unit bearing ucf208, make: schaeffler ( fag ) / skf / timken , unit bearing ucf210, make: schaeffler ( fag ) / skf / timken , unit bearing fl206, make: schaeffler ( fag ) / skf / timken , unit bearing yar205 100 2f / fy505m, make: schaeffler ( fag ) / skf / timken , unit bearing ucf211, make: schaeffler ( fag ) / skf / timken , unit bearing ucfl206, make: schaeffler ( fag ) / skf / timken , unit bearing ucp206 / syj30tf, make: schaeffler ( fag ) / skf / timken , unit bearing ucp208 / syj40tf, make: schaeffler ( fag ) / skf / timken , unit bearing ucp210 / syj50tf, make: schaeffler ( fag ) / skf / timken , unit bearing ucp211 , make: schaeffler ( fag ) / skf / timken , unit bearing ucp211 32 / sy 2 tf, make: schaeffler ( fag ) / skf / timken , unit bearing ucp 212, make: schaeffler ( fag ) / skf / timken , unit bearing ucp 215, make: schaeffler ( fag ) / skf / timken , unit bearing uct208 / tuj 40 tf, make: schaeffler ( fag ) / skf / timken , unit bearing ucp 209, make: schaeffler ( fag ) / skf / timken , unit bearing uct210 / tuj 50 tf, make: schaeffler ( fag ) / skf / timken , unit bearing uct212d1, make: schaeffler ( fag ) / skf / timken , unit bearing syh 2.7 / 16 tf, make: schaeffler ( fag ) / skf / timken , unit bearing syj 2. tf, make: schaeffler ( fag ) / skf / timken , unit bearing syj 30 kf, make: schaeffler ( fag ) / skf / timken , unit bearing sy60 tf, make: schaeffler ( fag ) / skf / timken , unit bearing sym 2.7 / 16 tf, make: schaeffler ( fag ) / skf / timken , unit bearing saf 324, make: schaeffler ( fag ) / skf / timken , unit bearing saf 332., make: schaeffler ( fag ) / skf / timken , unit bearing sf 50, make: schaeffler ( fag ) / skf / timken , unit bearing st 50, make: schaeffler ( fag ) / skf / timken , unit bearing rsa60, make: schaeffler ( fag ) / skf / timken , unit bearing fyj511, make: schaeffler ( fag ) / skf / timken , unit bearing fytb506m, make: schaeffler ( fag ) / skf / timken , withdrawal sleeve ah2340 / 180, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , withdrawal sleeve aoh24172, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h207 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h208, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h209, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h210 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h211 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h213, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h215, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h217, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2311 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2313 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2315, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2316, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2317, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2318 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2330 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2332, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2334 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2336, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2340, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h2344, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3024, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3036, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3044, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h309 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h308, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h310, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h311 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h312 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h315, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h316, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h317 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h 2322, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3124 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3126 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3128, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h313 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3130, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3132, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3134 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3136, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3140 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3144, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h315 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3152, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h3156, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h317 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h318 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h320 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve h322 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 211, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 213, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 215 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 216, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 217, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 311, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 3136, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 315, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 317, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he 320, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he211, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve he215 , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve hm56t, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 25 es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 100 es, spherical plainmake: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 30 es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge31zo, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 35 es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 40 es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 45 es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 50 es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 60 es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 76 zo, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 90 es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve ge 90 es 2rs, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve geh 50 es 2rs, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve gez 104es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve gez 108es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve gez 200 es 2rs, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve gez 204 es 2rs, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve gez 208 es, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve gez 208 es 2rs, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve gez 300 es , spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve gez 308 es 2rs, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , sleeve gaz 400 sa, spherical plain , make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb 5 / 160, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb7.5 / 280, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb 8 / 80, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb 9 / 90, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb 12.5 / 150, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb 12.5 / 160, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb 13.5 / 200, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb 13 / 230, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb 14 / 215, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frb15 / 250, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block frm 130 / 12.5, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block fsnl 518 615 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block fsnl 522 619 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block fsnl 524 620. with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block fym 2.7 / 16 tf, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block lor 156, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block lor 119, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block lor 127, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snh 510 tl with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block se 510 608, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn508 / snh 508 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn509 / snh 509with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 511 / snh 511 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 512 / snh 512 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 513 / snh 513 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 514with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 518 / snh 518 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 522 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 524 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 532 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 515 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 517 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sn 617 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block saf 218 ( four hole ) with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block saf222 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block saf 332 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block saf 224 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sd3136ts, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snh 515 tl with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snh 517 tl with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snh 520 tl with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snh 526 tl with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snh 528 tl with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snh 530 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snl 218 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snl 528, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snl 3044 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snl 3140, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snl 3134, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snl 3136, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snl 515tl, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snl 518 615, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block snl 524 620, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sr 0 24, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block sr 38 32, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block tsn 510, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block mb 10, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block mb26, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block km26, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , plummer block thdd 3132 with labyrinth, make: schaeffler ( fag ) / skf ( sibco ) / timken / ntn , taper roller bearings metric series 30203, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30204, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30205, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30206, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30209, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30210, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30212, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30213, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30214, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30215, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30216, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30218, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30232, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30309, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30311, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30313, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30315, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30312, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30317, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30632, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 31305, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 31309, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 31310, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 31311, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 31313, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 31314, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 31315, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 31317, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 31318, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series hr32212j, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32005, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32006, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32007, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32008, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32010, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32012, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32019, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32026, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32032, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32036, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32207, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32208, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32211, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32213, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32214, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32216, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32217, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32218, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32219, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32220, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32226, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32308, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32311, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32314, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32316, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32318u, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32324, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32316, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 33217, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 33220, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30314d, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 30315d, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32009 / x, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32016x / q, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32018xa, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32030xm90km3, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32032xm90km4, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 32217 / q, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 33013, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings metric series 33109, steel cage, make: schaeffler ( fag ) / skf / timken , taper roller bearings inch series 11162 / 11300, make: timken , taper roller bearings inch series 19268 / 19150, make: timken , taper roller bearings inch series 28622 / 28680, make: timken , taper roller bearings inch series 31314 / 30314d, make: timken , taper roller bearings inch series 3420 / 3490, make: timken , taper roller bearings inch series 34304 / 34478, make: timken , taper roller bearings inch series 34306 / 34478, make: timken , taper roller bearings inch series 3779 / 3730, make: timken , taper roller bearings inch series 382 / 388a, make: timken , taper roller bearings inch series 387a / 382a, make: timken , taper roller bearings inch series 395 s / 394 a, make: timken , taper roller bearings inch series 39573 / 39520b, make: timken , taper roller bearings inch series 3980 / 3920, make: timken , taper roller bearings inch series 3982 / 3920, make: timken , taper roller bearings inch series 42350 / 42587d, make: timken , taper roller bearings inch series 44158 / 44363d, make: timken , taper roller bearings inch series 4595 / 4535, make: timken , taper roller bearings inch series 462 / 453x, make: timken , taper roller bearings inch series 462 / 454, make: timken , taper roller bearings inch series 495 / 4535, make: timken , taper roller bearings inch series 46780 / 46720, make: timken , taper roller bearings inch series 48620 / 48684, make: timken , taper roller bearings inch series 48684 / 48620, make: timken , taper roller bearings inch series 48685 / 48620, make: timken , taper roller bearings inch series 48220 / 48290, make: timken , taper roller bearings inch series 4t 29586 / 4t 29520, make: timken , taper roller bearings inch series 4t 357 / 4t 354a, make: timken , taper roller bearings inch series 4t 543 / 4t 532x, make: timken , taper roller bearings inch series 529 / 522, make: timken , taper roller bearings inch series 56418 / 56650cd, make: timken , taper roller bearings inch series 56418 90015, make: timken , taper roller bearings inch series 56418 90013, make: timken , taper roller bearings inch series 56425 / 56662, make: timken , taper roller bearings inch series 567 / 563, make: timken , taper roller bearings inch series 632 / 639, make: timken , taper roller bearings inch series 6420 / 6460, make: timken , taper roller bearings inch series 64450 / 64700, make: timken , taper roller bearings inch series 645 / 632, make: timken , taper roller bearings inch series 6580 / 6535, make: timken , taper roller bearings inch series 67388 902a, make: timken , taper roller bearings inch series 67388 / 67322d, make: timken , taper roller bearings inch series 72200 / 72487, make: timken , taper roller bearings inch series 740 / 743, make: timken , taper roller bearings inch series 752 / 759, make: timken , taper roller bearings inch series f4b scm 203ff, make: timken , taper roller bearings inch series h913842 / 913810, make: timken , taper roller bearings inch series hm813841 / hm813810, make: timken , taper roller bearings inch series hm907635 / hm907614, make: timken , taper roller bearings inch series hm907639 / hm907614, make: timken , taper roller bearings inch series 27691 / 27620, make: timken , taper roller bearings inch series jm719149 / 719113, make: timken , taper roller bearings inch series jrm3535h 90ub1, make: timken , taper roller bearings inch series l433749 / 433710, make: timken , taper roller bearings inch series l540049 / 540010, make: timken , taper roller bearings inch series l910349 / l910310, make: timken , taper roller bearings inch series lm104949 902a5, make: timken , taper roller bearings inch series lm613449 / lm613410, make: timken , taper roller bearings inch series lm718947 / xc18140d, make: timken , taper roller bearings inch series lm814849 / lm814810u, make: timken , taper roller bearings inch series mu 1305 tm, make: timken , taper roller bearings inch series mu1309, make: timken , taper roller bearings inch series mu5207t, make: timken , taper roller bearings inch series na366 / 366d, make: timken , taper roller bearings inch series t251 9041a, make: timken , taper roller bearings inch series 64450 20014, make: timken , taper roller bearings inch series 32030 jr in set, make: timken , taper roller bearings inch series 32026 xu in set, make: timken , taper roller bearings inch series jrm 3535h, make: timken , taper roller bearings inch series 90014 in set, make: timken , taper roller bearings inch series mu1309rugvw140, make: timken , taper roller bearings inch series 32217 / hr32217j, make: timken , taper roller bearings inch series 535 99401, make: timken , taper roller bearings inch series 3779 / 3730, make: timken , taper roller bearings inch series 74550 90220, make: timken , taper roller bearings inch series 90181 90021, make: timken , taper roller bearings inch series 90381 90021, make: timken , taper roller bearings inch series 387a 20024, make: timken , taper roller bearings inch series 388a / 382, make: timken , taper roller bearings inch series 4t 30311d, make: timken , taper roller bearings inch series 56418cd, make: timken , taper roller bearings inch series 56650cd, make: timken , taper roller bearings inch series 452319m2, make: timken , taper roller bearings inch series 452322m2, make: timken , taper roller bearings inch series j90354, make: timken , taper roller bearings inch series j90748, make: timken...
34755463 supply of spares for 4.1 / 4 standard head cone crusher required for ucil at jaduguda, jharkhand 1 counter shaft & pinion sub pt.no: 07090010113 2 thrust bearing assembly pt. no: 7090020004 3 bevel gear pt no; 0700005738t 4 inner counter shaft bushing pt no: 700048c102 5 outer counter shaft bushing pt no: 700048c102 6 oil flinger pt no: 0700056664t 7 piston wear ring seal pt. no:01063084703...
34045001 bids are invited for strg cylinder assy lh , pump coupling assy , bush , pin fab 149x80x50 , slotted nut , bush nylon mo s2 , pin , pin steering jack rear , spacer goose neck lubelon , bush goose neck lubel on , bearing washer , thrust bearing , bearing cup , washer special , tie bolt , tie bolt spring , thrust washer , nut 36x3 , engine mtg rubber pad , rubber pad radiator , clutch release bearing , seal kit steering jack , coupling nit with brake disc , rearaxle , gasket top cover , bull gear , t r bearing32212 , trumpet housing lh rh astha , gaskettrumpet housing , bull pinion shaft left , needlebearing , needle cage , bull pinion shaft rh , covertrumpet , oil seal , gasket , oil seal 50x72x8 , brakeliner assy , winch assembly , h p hose sae100r12 ,hose , h.p hose total quantity : 73...
33773317 bids are invited for spherical roller bearing with sleeve 23134cck plus h3134, make skf or fag or timken or ntn only , spherical roller bearing with sleeve 23140cck plus h3140, make skf or fag or timken or ntn only , spherical roller bearing withsleeve 23224cck plus h2324, make skf or fag or timkenor ntn only , thrust bearing t251 904 a 1, make skf or fagor timken or ntn only total quantity : 36...
32693677 bids are invited for bearing no. 6306 , bearing no. 6308 , bearing no. 6307 , load thrust bearing no. 29416e , roller bearing no. nu 411, ball bearing no. nu 318 total quantity : 114...
32685091 repairing, rectification, maintenance & overhauling works with spares of one akgi make tugger haulage assembly of 7, 8 incline of dhori ( k ) colliery, ( local sl no akgi / th / e&m / 01 ) 1.01 akgi tugger haulage shaft damaged bearing seats welding & machining as per bearing size & alignment checking, straightening, polishing, threads cleaning. 1.02 damaged bearing housing seat of haulage drum mounting bracket welding by c.i electrodes & machining std size 1.03 2nd motion 64teeth pinion damaged & broken teeth repairing & re buildup by cast steel special teeth making electrodes & its shaping by grinding & matching with 16 teeth drive pinion for akgi make tugger haulage. 1.04 tugger gear bearing housing damaged bearing seat c.i welding & machining as per bearing size. 1.05 haulage drum damaged & worn out bearing seat repairing by c.i welding & machining by hand operated lathe machine. 1.06 gun metal thrust bearing new making with casting, machining, boring, grooving for drum balancing. 1.07 old & damaged brake lining cutting & fixing as required size. 1.08 brake lining complete new making with liner. 1.09 tugger haulage sun pinion, star pinion, drive pinion, master pinion all teeth’s checking one by one & its cheeps cleaning by grinding/shaping 1.1 all threads cleaning, new threads making, over size threads making. 1.11 repair kit like as keys, locks, h.t allen bolts, hexagonal head bolts, spring washer. 1.12 all pinions, body & bearings cleaning, washing & greasing. 1.13 akgi haulage clutch & break operating accessories new making & fabricating like pins, clutch bolts, studs, adjusting handle, “u” gutki, bolts nuts. 1.14 complete dismantling, overhauling, greasing, resetting, assembling. ...
32275152 bids are invited for spherical roller bearing with sleeve 23134cck plus h3134, make skf or fag or timken or ntn only , spherical roller bearing with sleeve 23140cck plus h3140, make skf or fag or timken or ntn only , spherical roller bearing withsleeve 23224cck plus h2324, make skf or fag or timkenor ntn only , thrust bearing t251 904 a 1, make skf or fagor timken or ntn only total quantity : 36...
32058967 e quotation transformer repairing and motor control panel electro mechanical equipments and its allied works 1 repairing and overhauling of 60hp v.t. pump set at raw water and 60hp c / f pump set at clear water, s / f of new motor contrl panel and repairing of stabilizer at rural multi panchayat water supply scheme telmachho 1.01 cost towards lifting of v.t. pump set from well and lowering the same after repairing with all labour tools and tackles 1.a cost towards dismantling of 60hp v.t. pump and checking, repairing and changing of following parts such as : ( for each pump ) 1.01 pump shaft of s.s materials ( 50mm. dia ) as per sample 1.02 impeller lock bush of s.s. material as per sample 1.03 impeller key 1.04 s.s housing bush ( 80 m.m dia ) 1.05 line shaft coupler of s.s.1.06 line shaft of s.s.materials ( size1.5mtr x32 m.m. dia ) 1.07 elen screw 1.08 6 dia c.i. spider bearing with cutless rubber bush. 1.09 top shaft of s.s. materials as per sample 1.10 check nut 1.11 neck ring bush of g.m 1.12 housing bolt of size m12x80mm 1.13 gland tightener with stud and nut 1.14 c.i. gland stuffing box with g.m. bush 1.15 coluum pipe bolt with nut ( m16 x90mm ) 1.16 cost of s / f of oil seal 1.17 cost for repairing of g.m.impeller by gas welding and machining as per required size with materials and lath work 1.18 cost for s / f of 6 dia x 6mm thick flanged type column pipe of 5 length each made of erw casing pipe heavy duty as per sample. 1.19 overhauling of 2 nos of 60h.p. sq.cage vertical solid shaft induction motor, dismentalling, cleaning andheating, vernishing re assembly etc all complete. 1.20 cost for s / f of ball bearing for 60 h.p. motor ( skf 6313 2nos and greesing assembling, and testing. 1.2 1 cost for s / f of …skf make …ball bearing 6317 01nos thrust bearing skf 7316 bep for both p / set 1.22 s / filling of c.oil about 10 ltr in each pump 1.23 cost for s / f of 6 dia cidi nr valve of rather pn, of isi marked of and reputed make for both sets 1.24 cost for repairing of motor control panel and changing of digital meter 1no, starter 1set, 250amp. mccb 1no with all material and labour charges. 1.25 cost for s / f of 315 amp 4 pole change over switch 1.26 cost for supply and fitting of terminal end / lux of required size 1.27 cost for supply and laying of 150mm sq. 3.5 core pvc insulate and pvc sheathed armoured cable 1100 volt grade with isi mark solid / standred aluminium conductor with 6mm thick 25mm width m.s. spacer with gi pipe earth wire 6sq mm complete in an approved manner as per is 7098 1.28 cost for transportation from pumping plant to work shop and from work shop to p / p2.02 cost towards all, labour, tools, tackles and highly skilled technician for opening, checking fault, cleaning and doing complete servicing of 3 mva 11kv / 3.3kv outdoor transformer with filteration of existing transformer oil up to desire quality. supply and filling of fresh transformer oil up to desire level approx 400 litres, including s / f of all required materials such as, hv bushing 3 set, lv bushing 3 set., hv & lv insulator 6 nos., copper stud 6nos., with 4 nos. nut & copper washer, silca gel, laborized gasket sheet etc all complete, with all labour tool, tackles, technician, and transportation cost. etc. ( rate after deducting the scrap materials ) . 2.03 cost towards all, labour, tools, tackles and highly skilled technician for opening, checking fault, cleaning and doing complete servicing of 1mva 11kv / 415v outdoor transformer with filteration of existing transformer oil up to desire quality. supply and filling of fresh transformer oil up to desire level approx 210 litres, including s / f of all required materials such as, hv bushing 3 set, lv bushing 3 set., hv & lv insulator 6 nos., copper stud 6nos., with 4 nos. nut & copper washer, silca gel, laborized gasket sheet etc all complete, with all labour tool, tackles, technician, and transportation cost. etc. ( rate after deducting the scrap materials ) . 3 supply, fitting, installation and commissioning of current protection & control relay, under voltage over voltage relay and its allied works at wtp bhelatand of dhanbad urban water supply scheme phase 1 3.01 cost towards supply, installation and commissioning of current protection & control relay, make c&s electric ltd., type / model csenex i 202, in 1a / 5a, fn 50 / 60 hz for incomer panel, with doing all electric connection, making accurate setting for load and tripping etc all complete with all labour, tools, tackles and highly skilled technician charges. 3.02 cost towards supply, installation and commissioning of under voltage over voltage relay, make c&s electric ltd., type / model irupro uor 1 o, fn 50 / 60 hz for incomer panel, with doing all electric connection, making accurate setting for load and tripping etc all complete with all labour, tools, tackles and highly skilled technician charges. 3.03 cost towrads supply and laying of 10core x 2.5 sq. mm copper control cable 1100v grade, isi marked, make havells / polycab / rr / finolex / any reputed make. 3.04 cost towards supply, installation and commissioning of motor protection relay, for 3.3 kv motor feeder panel, with doing all electric connection, making accurate setting for load and tripping etc all complete with all labour, tools, tackles and highly skilled technician charges.make c&s electric ltd. / any isi marked reputed make.3.05 cost towards supply, installation and commissioning of master tripping relay, with doing all electric connection, making accurate setting for load and tripping etc all complete with all labour, tools, tackles and highly skilled technician charges.make c&s electric ltd. / er / any isi marked reputed make. 3.06 cost towards supply, installation, testing and commissioning of ct, ratio class p.s. ( protection special ) , pole mounted type, with doing all electric connection, with all labour, tools, tackles and highly skilled technician charges.make c&s electric ltd. / cg / any isi marked reputed make. 4 supply, fitting, installation and commissioning of current protection & control relay, under voltage over voltage relay and its allied works at intake well raw water pumping plant of dhanbad urban water supply scheme phase 1 4.01 cost towards supply, installation and commissioning of current protection & control relay, make c&s electric ltd., type / model csenex i 202, in 1a / 5a, fn 50 / 60 hz for incomer panel, with doing all electric connection, making accurate setting for load and tripping etc all complete with all labour, tools, tackles and highly skilled technician charges. 4.02 cost towards supply, installation and commissioning of under voltage over voltage relay, make c&s electric ltd., type / model irupro uor 1 o, fn 50 / 60 hz for incomer panel, with doing all electric connection, making accurate setting for load and tripping etc all complete with all labour, tools, tackles and highly skilled technician charges. 4.03 cost towrads supply and laying of 10core x 2.5 sq. mm copper control cable 1100v grade, isi marked, make havells / polycab / rr / finolex / any reputed make. 4.04 cost towards supply, installation and commissioning of differential numerical transformer protection relay, fn 50 / 60 hz for incomer panel, with doing all electric connection, making accurate setting for load and tripping etc all complete with all labour, tools, tackles and highly skilled technician charges. [ make schneider ( micom ) / c&s / any isi marked reputed make ] 4.05 cost towrds supplying, erecting approved make h.t. outdoor type, , gang operated air break triple pole switch suitable for 33kv line, double brake type with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps. 4.06 cost towards supply, installation and commissioning of motor protection relay, for 11 kv motor feeder panel, with doing all electric connection, making accurate setting for load and tripping etc all complete with all labour, tools, tackles and highly skilled technician charges.make c&s electric ltd. / any isi marked reputed make. 4.07 cost towards supply, installation, testing and commissioning of ct, ratio class p.s. ( protection special ) , pole mounted type, with doing all electric connection, with all labour, tools, tackles and highly skilled technician charges.make c&s electric ltd. / cg / any isi marked reputed make. 5 servicing, filteration and filling of fresh transformer oil for 7.5mva ( 33kv / 11kv ) transformer 1no., 750 kva ( 11kv / 0.415 kv ) transformer 1no. and its allied works at intake well raw water pumping plant of dhanbad urban water supply scheme phase 1 5.01 cost towards all, labour, tools, tackles and highly skilled technician for opening, checking fault, cleaning and doing complete servicing of 7.5 mva 33kv / 11kv outdoor transformer with filteration of existing transformer oil up to desire quality. supply and filling of fresh transformer oil up to desire level approx 520 litres, including s / f of all required materials such as, hv bushing 3 set, lv bushing 3 set., hv & lv insulator 2 nos., copper stud 3nos., with 4 nos. nut & copper washer, silca gel, laborized gasket sheet etc all complete, with all labour tool, tackles, technician, and transportation cost. etc. ( rate after deducting the scrap materials ) . 5.02 cost towards all, labour, tools, tackles and highly skilled technician for opening, checking fault, cleaning and doing complete servicing of 750 kva 11kv / 415v outdoor transformer with filteration of existing transformer oil up to desire quality. supply and filling of fresh transformer oil up to desire level approx 230 litres, including s / f of all required materials such as, hv bushing 3 set, lv bushing 3 set., hv & lv insulator 6 nos., copper stud 6nos., with 4 nos. nut & copper washer, silca gel, laborized gasket sheet etc all complete, with all labour tool, tackles, technician, and transportation cost. etc. ( rate after deducting the scrap materials ) . 6 supply installation testing and commissioning of chlorine tank, and its allied work at chlorine house, at wtp bhelatand 6.01 cost towards supplying, installation, testing and commissioning of 900kg cylinder of liquified chlorine ton containers as per latest isi standards and made of standard grade. moc sa 516 gr 70, safe wp: 20kg / cm2 g, d.p.: 20.771 kg / cm2 g, dt 65 / 100c, fr 1.19 itp 30.00kg / cm2 g wcap 775.6kg with filled of chlorine etc all complete with all labour tools tackles, materials, and transporting charges for 77mld wtp bhelatand chlorine house . etc...
31897243 e quotation for seeking firm rates for non schedule items for preparing estimates. gr c repairing of electro mechanical assets and all their associate works like repairing of motors, pumps, starters, panel, cables etc. at rinpas, kanke, ranchi , c / f pump sets , cost towards dismantling of 100 hp wpil make single stage c / f pump and taking out its rotating unit assembly with changing of damaged parts by new making s / f neck ring as per sample size 2 nos, c.i shaft sleeve as per sample size – 2nos, making s / f shaft sleeve check nut as per sample size – 2 nos , s / fball bearing skf 6309 2 nos and repairing of bearinghousing by welding turning machining as per bearing size 2 nos, c.i gland tightner as per sample size – 2nos including cost of reassembling of rotating unit assembly balancing rotating unit assembly and fitting the pump with supply of grease gland packing oil packing paper with transporting cost of rotating unit from p / plant to workshop and back , cost toward supplying fitting & changing of 100 hp jyoti make motor ball bearing skf 6316 at de side 1 no. and sk 6314 nde 1 no. with grease. , cost towards repairing of 100 hp l & t make f.a.s.d starter with s / f contactor set 2 sets ) , relay unit ( 85 135a ) 1set, timer unit 1 set, making new connection etc all complete. , supplying and fitting 6”dia tyre coupling complete set with nut bolt washer and tyre of reputed make for 100 hp pump set. , cost towards supplying and fitting mccb 630 amp. for bus bar make l&t schneider / bch , cost towards supplying and fitting mccb 250 amp. for bus bar make l&t schneider / bch , cost toward supplying fitting & changing 100mm dia cidf sluice valve ( pn 1 ) 1 set & cidf nr valve ( pn 1 ) 1 no. including fitting charge , cost toward supplying fitting & changing 150 mm dia ci foot valve hiding single leather flat and gun metal seating all complete. , cost towards providing all labours tools & techniciansfor dismantling and disconnecting of 40 hp kirloskar make motor and taken out rotor from motor stator cutting removing burnt and damaged coil and after repairing refitting the same etc all complete. , cost towards full rewinding of 40 hp motor stator with supplying of super enameled round copper conductor suitable gauge class f insulating materials making all connection taping, varnishing with dr beck varnish all complete with deducting the cost of taken out scrap materials ( wt. of wire is 18.5kg approx ) . , s / f ball bearing skf make 6312&6309 at de&nde side of 40 hp kirloskar make motor including proper greasing all complete. , cost towards providing all labour tools and tackles for dismantling of 40 hp single stage kirloskar make c / f pump with changing damaged parts such as gm neck ring as per size and sample 2 nos. shaft sleeve 2 nos. shaft sleeve check nut 2 nos. making ci bearing housing as per size and sample 2 nos. supplying and fitting ball wearing skf make 6309 2nos. making supplying and fitting ms gland tightner as per size and sample 2 pair making citric motion of rotating unit assembling on lathe m / c etc all complete , cost towards repairing of 40 hp l&t motor starter by supplying and fitting l&t make 3 core ml 4 power contactor 45 amp. with auxiliary contractor complete set 2nos. supplying and fitting timer type lt 100 1nos., over load relay suitable range 1nos.etc all complete. , cost towards providing all labours tools & technicians for taking out damaged 250amp. tpn hrc fuse type disconnector main switch replacing new disconnector fuse unit with hrc fuse 1 set doing electrical connection and testing on full load after deducting the cost of taken out scrap materials , supplying and fitting 6”dia tyre coupling complete set with nut bolt washer and tyre of reputed make for 40 hp pump set. , cost towards providing all labour tools and tackles for dismantling and taken out damaged nr valve and s / f 4”dia c.i df nr valve heavy duty rating pn 1 isi marked on delivery pipe line with all work including cost of labour charge all complete testing on full load with deducting the cost of scrap materials. , cost towards supplying and laying 50 mm² x 3.5 core aluminium armoured cable from main switch to industrial panel. ( both sets ) . , cost towards supplying and laying 16 mm² x 3 core copper cable from panel to starter and starter to motor in bunch of two. ( both sets ) . , cost towards replacing damaged suction pipe by making supply & fitting 100 mm dia heavy duty m.s. suction pipe 10feet long both and 100 mm dia m.s. flange welding, 100mm dia long bend 1 no with nut bolt rubber insertion etc required for the job. , transportation charge of above p / set from work site to work shop and vice versa including loading and unloading charge. , submersible pump sets , cost towards providing all labour tools and technicians for dismantling and taken out 5hp submersible p / set with column pipe for bore well. , cost towards for rewinding and repairing of5 hp submersible motor with s / f 1.2 swg round copper winding wire 24 slot, gun metal bush, thrust plate, thrust bearing, diapharm, oil seal, etc with lathe work. all complete. after the deduction of cost of scrape materials. , cost towards repairing of5 hp submersible pump with s / f norylimpeller as per size and sample, diffuser, s.s. shaft, s.s. coupling, s.s. sleeve, nut, c.i. suction casing, c.i nrv etc. all complete ( 23 stage ) after the deduction of cost of scrape materials. , cost towards s / f and changing of 2”dia upvc column pipe with heavy duty socket ( make supreme / paras ) for both sets. , cost towards replacement of damaged submersible cable by supplying and fitting 4 mm2x 3 core flat submersible cable including cable jointing all complete. after the deduction of cost of scrape materials. dwsd m1062 , providing all labour, tools tackles& technicians for lowering of 5hp submersible pump set with all accessories in the bore well , cost towards supplying and fitting ( 1 ) 50 mm dia g.m. full way valve – 1 no ( 2 ) 40 mm dia nr valve – 1 no ( 3 ) 40 mm dia g.i. bend ( 4 ) 2” dia m.s. clamp with nut bolt 2 pair after the deduction of cost of scrape materials. , supplying and installation suitable size panel board for 5 hp submersible pump including fixing on wall comprising of following points such as ( 1 ) d.o.l starter 1no. ( 2 ) hrc fuse – 3 no. ( 3 ) voltmeter with selector switch – 1 set ( 4 ) ammeter with selector switch – 1 set ( 5 ) phase indicating neon lamp – 3 nos. etc. all complete after the deduction of cost of scrap materials. , supplying all material such as 40 mm dia g.i. pipe medium quality 15 ft. long, charcoal salt etc. for making earthing station as per i.e. rule , supplying and laying ground and on wall 10 swg, g.i. wire for doing continuous earthing for all electrical equipments , cost towards replacement of old and damaged underground service line by supplying new overhead line 10 mm² 3core copper wire after the deduction of cost of scrap materials. , supplying and laying ( under and over ground ) 2 dia aqua gold weather proof pvc pipe from bore well to main rising pipe line ( damaged pipe replacement ) make supreme / isi mark ( both sets ) , supplying and laying 1.5 dia under and over ground supreme aqua gold / any reputed make weather proof upvc pipe from bore well to dharamshala over head tank. , supplying and fitting union 1.5 dia , supplying and fitting elbow 1.5 dia , supplying and fittingtee 1.5 dia , supplying and fitting socket 1.5 dia , supplying and fitting upvc valve 1.5 dia , transportation charge of above p / set from work site to work shop and vice versa including loading and unloading charge....
31897240 e quotation for seeking firm rates for non schedule items for preparing estimates. repair and replacement of plumbing fixtures, cleaning of toilet and bathroom of inter ward, icu ward, staff room, female ward, w.w. ward, d.b. ward, duty room, main office building, a. ward, opd, drug store etc. and repairing of submersible pump set, , 10 hp c / f pump set , cost for complete rewinding of 10 h.p sq. cage induction motor operated on 415v, 3 phase, 50 c / s 1460 rpm with supply fitting of super enameled copper wire and other required insulation materials, heating assembly of the motor and testing on load ( wt of burnt coil 5.5 kg ) , cost for dismantling of 10 h.p c / f pump checking and changing of its damaged parts such as pump shaft of en 9 materials 01 no. key 02 nos. gland tightner 2 sets, gland tightner stud 4 nos. c.i bearing housing with cap 2 sets, ball bearing 6306 ( skf ) 2 nos. casing stud 16 mm sq. x 80 mm long with nut 8 nos. packing paper. grease, gland packing etc all complete and testing on load. , cost for supply and fitting of 3 dia tyre coupling complete set with nut, bolt & tyre. all complete. , cost for supply and fitting of 4 dia g.m flap tyre foot valve with packing and nut & bolt 4 nos. etc all complete. , cost for supply and fitting of 3 dia cidf heavy duty sluice valve, isi marked , cost for overhauling and repairing of motor control panel and changing of its damaged parts such as contactor ( ml 4 ) 3 nos., vm 02 nos., am 01, selector switch 2 nos, 100 amp mccb – 1 no, etc all complete and testing on load. , 3 h.p. submersible p / set , providing all labour, tools, tackles and technicians for taking out 3 h.p. submersible pump set with column pipe for bore well , cost towards for rewinding and repairing of 3 h.p submersible motor with s / f suitable winding wire, bronze bush etc. all complete after the deduction of cost of scrape materials. , cost towards repairing of 3 h.p. submersible pump with s / f bronze impeller as per size and sample, bush, thrust plate, pump shaft etc. all complete after the deduction of cost of scrape materials. , cost towards replacement of damaged submersible cable by supplying and fitting 2.5 mm2x 3 core flat submersible cable including cable jointing all complete for both set. jsor cb 1 3 after the deduction of cost of scrape materials. , cost towards supplying fitting, changing 2” dia g.i. column pipe with heavy duty socket ( make zindal / tata ) jsor 9k vi after the deduction of cost of scrape materials. , cost towards supplying and fitting ( 1 ) 2 dia g.m. full way valve – 1 no ( 2 ) 2 dia nr valve – 1 no ( 3 ) 2 dia g.i. bend 2 nos. ( 4 ) 2” dia m.s. clamp with nut bolt 2 pair after the deduction of cost of scrape materials. , providing all labour, tools tackles and technicians for lowering of 3 h.p submersible pump set with all accessories in the bore well , providing all labour, tools tackles and technicians for lowering 3 h.p.submersible pump set with all accessories in the bore well , 5 h.p. / 7.5 h.p. submersible p / set , providing all labour, tools, tackles and technicians for taking out 5 h.p. submersible pump set with column pipe ( 280 ) from bore well , cost towards for rewinding and repairing of5 hp submersible motor with s / f 1.0 swg round copper winding wire 24 slot, gun metal bush, thrust plate, thrust bearing, diapharm, oil seal, etc with lathe work. all complete. after the deduction of cost of scrape materials. , cost towards repairing of 5 hp submersible pump with s / f noryl impeller as per size and sample, diffuser, s.s. shaft, s.s. coupling, s.s. sleeve, nut, c.i nrv etc. all complete ( 23 stage ) after the deduction of cost of scrape materials. , cost towards replacement of damaged submersible cable by supplying and fitting 4 mm2x 3 core flat submersible cable including cable jointing all complete. after the deduction of cost of scrape materials. , cost towards supplying fitting, changing 2” dia g.i. column pipe with heavy duty socket ( make zindal / tata ) after the deduction of cost of scrape materials. , cost towards supplying and fitting ( 1 ) 50 mm dia g.m. full way valve – 2 no ( 2 ) 50 mm dia nr valve – 1 no ( 3 ) 50 mm dia g.i. bend ( 4 ) 2” dia m.s. clamp with nut bolt – 2 pair after the deduction of cost of scrape materials. , supplying and laying ground and on wall 10 swg, g.i. wire for doing continuous earthing for all electrical equipments , providing all labour, tools tackles and technicians for lowering ( 280 ) of 5 h.p.submersible pump set with all accessories in the bore well , supplying and installation suitable size panel board for 5 h.p. submersible pump including fixing on wall comparising of following points such as ( 1 ) d.o.l starter – 1 no. ( 2 ) hrc fuse – 3 no. ( 3 ) volt meter with selector witch 1 set ( 4 ) ammeter with selection switch – 1 set ( 5 ) zindicating neon lamp – 3 no. etc. all complete after the deduction of cost of scrape materials. , supplying of plumber & sweeper for engaged to maintenance of water supply, cleaning of toilet and bathroom, sewer line etc. operating of pump, f.w.v fro interrupted water supply etc. all complete as per direction of e / i. ( including contractor profit ) . period from 01.04.2022 to 31.03.2023 ( i ) ( plumber ) 12 month x 26 days x 1 nos. = 312 nos. , ( ii ) sweeper 12 month x 26 days x 1 nos. = 312 nos. , provision leake repairing of different and size of upvc sch 80 pipe in place of existing / cracked and damaged pipe of isi approved make or equivalent make damaged pipe in trenchage and replacement of pipe and fitting so as to give. i m average cover over the socket of pipes with disposal of excavated earth within initial lead and lift and necessary fitting and earth work in backfilling and cutting pipe to size etc. all complete as per specification and direction of e / i. leakage in 50 mm dia upvc pipe , leakage in 40 mm dia upvc pipe , leakage in 32 mm dia upvc pipe , leakage in 25 mm dia upvc pipe , leakage in 20 mm dia upvc pipe , provision leake repairing of different and size of upvc sch 80 pipe in place of existing / cracked and damaged pipe with red lead and yarn of following nominal bore screwed and socketed joints on wall, ceiling and floor including supplying and fitting on wall hooks or pipe clamp wooden plugs, cutting pipe to size and threading ends where necessary etc. all complete as per specification and direction of e / i. leakage in 50 mm dia upvc pipe , leakage in 40 mm dia upvc pipe , leakage in 32 mm dia upvc pipe , leakage in 25 mm dia upvc pipe , leakage in 20 mm dia upvc pipe , supplying and flaxing u pvc ball valve of approved make all complete as per direction of e / i. 50 mm dia u pvc ball valve , 40 mm dia u pvc ball valve , 32 mm dia u pvc ball valve , 25 mm dia u pvc ball valve , 20 mm dia u pvc ball valve , supplying of material for consumption to day to day works direction of e / i. ( a ) hydrochloric acid ( 500 ml ) , ( b ) bleaching powder ( 25 kg bag ) , ( c ) phenyl liquid ( 1 ltr. ) , ( d ) harpic liquid ( 1 ltr. ) , ( e ) surf ( 1 kg ) , ( f ) nariyal broom , ( g ) pochha broom , ( h ) safi , ( i ) dettol ( 500ml ) , ( j ) phenyl goli ( pkt ) , ( k ) odonil , ( l ) room freshner , ( m ) phooll broom , ( n ) lizol ( 500 ml ) , ( o ) plastic bucket ( 10 l ) , ( p ) plastic mug ( 1 l ) , supplying of materials for c.p. bathroom fitting ( as per schedule rate ) to consumrtion day to day work. 15mm dia c.p. bib cock ( long thread ) , 15mm dia c.p. pillar cock ( long thread ) , 15mm dia c.p. angular stop cock ( long thread ) , 15mm dia cp basin mixture , 15mm dia cp wall mixture , jet sprey , health faucet , bib cock spindle , a ) medium size , b ) large size , mirror , towel rail , soap dish , 32mm dia cp waste : , 32mm dia pvc waste pipe 750mm long with coupling : , 100mm dia c.p. jali : , 15mm dia and 45cm long pvc connection pipe : , sink waste , cistern ball cock , cistern handle , pvc water storage tank cover ( 2000 / 1000 l ) , 25mm dia ball cock set for pvc tank , cammod cover , m seal , waste pipe bundla , 10 lit pvc l / d cistern , flush bend , basin , supplying all materials, labours, tools and equipment for the fitting and fixing cp bathroom fittings in vip fittings including all accessories etc. all complete as per specification and direction of e / i. a ) sink mixture flr5309n jaquar , b ) wall mixture 3 in 1 with wall flange flr5281n jaquar , c ) central hole basin mixture with popup waste system 450mm long braided houses ( con 169knb ) jaquar , d ) pillar cock flr5011n jaquar , e ) bib cock with flange flr – 5053n jaquar , f ) cp bib cock 2 in 1 angular stop cock flr 5041n jaquar , g ) angular stop cock with flange flr 5053n jaquar , h ) health faucet ald 577 jaquar , i ) over head shower with arm ohs 1999 jaquar , j ) glass shelf 22 ( aqn 7771 ) jaquar , k ) towel rail ( akp 35711ps ) jaquar , l ) towel ring ( akp 35721p ) jaquar , m ) soap dish holder akp 35731p jaquar , n ) cp liquid soap dispenser with mettalic bottle acn1137n jaquar , supplying, fitting and fixing pvc pipes of approved make including supplying nails, clips and pvc washer cement & yarn for making plumber joints properly cutting pipe to sizes including earth work of scaffolding etc. where necessary etc. all complete as per specification and direction of e / i. 100mm dia pvc sewer pipe , 75mm dia pvc sewer pipe , supplying and fixing pvc fitting of approved make confirming to isi including supplying nails and bobbins from making solvent cement solution or gasket joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of e / i. 110mm swr nahani trap , 110mm swr plain bend , 110mm swr door bend , 110mm swr plain tee , 110mm swr door tee , 75mm swr plain bend , 75mm swr door bend , 75mm swr plain tee , 75mm swr door tee , providing all material, equipment and wash out and cleaning of 2000 / 1000 litre pvc water storage tank including rubbing the wall of tank by the help of coconut, rushi and bleaching powder their washing by clean water all complete as per direction of e / i. 3000 litre capacity hdpe w / s / tank 2 time x 3000 liter x 2 nos. = 12000.00 liter 2000 litre capacity hdpe w / s / tank 2 time x 2000 liter x 88 nos. = 372000.00 liter 1000 litre capacity hdpe w / s / tank 2 time x 1000 liter x 9 nos. = 18000.00 liter total = 402000.00 liter...
31195922 rotor complete 250hp 2900 / p.no. 1635 , thrust bearing complete / p.no. 1647 , pump shaft for 5 stages / p.no. 25002 , bearing bush for lower / p.no. 1637 , stator complete ( without winding ) / p.no. 1631 , impeller / p.no. 25005 , sand deflector / p.no. 25000 , suction case / p.no. 25003 , pump couple / p.no. 25029 , oil seal / p.no. 25001 , neck ring / p.no. 25010 , bearing bush for upper / p.no. 1630 , rotor sleeve lower / p.no. 1613...
30895672 procurement of pin, bearing, plate, spacer etc applicable for tata hitachi excavator rs 34 of rajmahal area ecl , pin stopper , bearingball , spacer , pin spring , plate thrust , pin spring , pin , plate thrust , bearing needle , pin , pin spring , plate thrust , bearing needle , pin , bearing needle...
30707971 bids are invited for bearing number 23936 cc spherical roller bearing, double row id 180mm, od 250mm w 52mm steel cage c3 , bearing number ncf 2936v3 cylindrical roller bearing, id 180mm, od 250mm steel cage c3 , bearingnumber 29422e spherical rooler thrust bearing id110mm, od 230mm w 73mm steel cage c3boq title bearing crusher total quantity : 20...
29809315 bids are invited for casing,stage,pn:108.02 casing,stage,pn:108.02for pump, model : hgc 5/9manufacturer : ksb pumps ltdpart no: 108.02 , wearing ring,last stage casing,pn:502.02 wearing ring,last stage casing,pn:502.02for pump,model:hgc 5/9manufacturer : ksb pumps ltdpart no: 502.02 , wearing ring,stage casing,pn:502.03 wearing ring,stage casing,pn:502.03for pump,model:hgc 5/9manufacturer : ksb pumps ltdpart no: 502.03 , retaining ring,pn:506 retaining ring,pn:506for pump,model : hgc 5/9manufacturer : ksb pumps ltdpart no: 506 , spacer sleeve,pn:525.01 spacer sleeve,pn:525.01for pump,model : hgc 5/9manufacturer : ksb pumps ltdpart no: 525.01 , spacer disc,pn:551 spacer disc,pn:551for pump,model:hgc 5/9manufacturer : ksb pumps ltdpart no: 551 , lubricating ring,pn:644 lubricating ring,pn:644for pump,model:hgc 5/9manufacturer : ksb pumps ltdpart no: 644 , shaft w/key,moc:1.4313.09/chpl,pn: 210 shaft w/key,moc:1.4313.09/chpl,pn:210for pump,model:hgc 5/9.manufacturer : ksb pumps ltdpart no: 210 , impeller,moc:1.4008.09,pn:230 impeller,moc:1.4008.09,pn:230for pump model : hgc 5/9manufacturer : ksb pumps ltdpart no: 230 , shell,bearing,pn:370 shell,bearing,pn:370moc:cst+wh.metalfor pump model : hgc 5/9part no: 370manufacturer : ksb pumps ltd , plate,thrust bearing,pn:384 plate,thrust bearing,pn:384for pump,model : hgc 5/9part no: 384manufacturer : ksb pumps ltd , bearing,thrust,segment,steel,pn: 387 bearing,thrust,segment,steel,pn:387for pump,model:hgc 5/9.manufacturer :ksb pumps ltdpart no:387 , set of gasket & o ring set of gasket & o ringfor pump,model:hgc 5/9.manufacturer : ksb pumps ltd , ring,labyrinth,al,gr 63400,pn:423 ring,labyrinth,al,gr 63400,pn:423for pump,model : hgc 5/9manufacturer : ksb pumps ltdpart no: 423 , packing set,gland,pn:461 packing set,gland,pn:461for pump, model : hgc 5/9manufacturer : ksb pumps ltdpart no: 461 , ring,split,pn:501 ring,split,pn:501for pump, model : hgc 5/9manufacturer : ksb pumps ltdpart no: 501 ,...
29686401 bids are invited for spare thrust pad of michell doublle thrust bearing model 08068 nfc for fk4e36 bfp(spare thrust pads , spare thrust pad of michell doublle thrust bearing model 08034 nfc for fa1b5 bp(spare thrust pads o , 8 dnt spare journal pad set of m/s michell make for cep (1 set= 8 nos. ) , ga drg. no. 5822 for bhel , 8 dnt spare collar, ga drg. no. 5822 for bhel make condensate extraction pump model no.en6j40. , 8 dnt spare cooler assembly, ga drg. no. 58227for bhel make condensate extraction pump model no. en ,8 dnt spare lower thrust pad set for cep (1 set= 8 nos. ) ,ga drg. no. 58227 for 1bhel make condensat , 8 dnt spareupper thrust pad set for cep (1 set= 16 nos. ) , ga drg. no.58227 for bhel make condensat total quantity : 7...
29495369 bids are invited for complete bowl assembly for clarified water pump, kbl make, model db 300/34 on oem basis , complete bowl assembly with accessories, kbl make, model vt250, stage on oem basis , thrust bearing assembly, kbl make, model vt 250, stage , discharge 100 m3/hr on oem basis , complete bowl assembly for dm pp, kbl make, model bhr 28 18 deg, stage 3 on oem basis , complete bowlassembly for wswp, kbl make, model bhr 28 18 deg,stage 1 on oem basis , complete bowl assembly for sdp,kbl make, model shs 100/32q, stage 1 on oem basis ,complete rotating assembly for degasser pump, kbl make,model 100/40, stage single on oem basis total quantity : 7...
29488548 part repairing including changing of thrust bearing of 2000 gpm rkb pump, make kirloskar, type rkb 250 / 46k, 3 stage, sl. no. 12972150008 located at quarry no. 03 under kathara colliery part repairing including changing of thrust bearing of 2000 gpm rkb pump, make kirloskar, type rkb 250 / 46k, 3 stage, sl. no. 12972150008 located at quarry no. 03 under kathara colliery...
29362867 bids are invited for combined thrust bearing & guide bearing coolers(heat exchanger) total quantity : 2...
29352733 bids are invited for bearing no. 6306 bearing no. 6306 , bearing no. 6308 bearing no. 6308 , bearing no. 6307 bearing no. 6307 , load thrust bearing no. 29416e load thrust bearing no. 29416e , ball bearing no. 6411 ball bearing no. 6411 , roller bearing no. 6318 roller bearing no. 6318 , roller bearing no. nu 411 roller bearing no. nu 411 , ball bearing no. 6313 ball bearing no. 6313 , ball bearing no. nu 318 ball bearing no. nu 318 total quantity : 1...
29205729 bids are invited for radial bearing b / up, ( cyl. ) , crm 3 pltcm , thrust bearing ( tapered ) b / up crm 3 pltcm , bearing w / r ( radial+ thrust ) , crm 3 pltcm , bearing imr ( radial+ thrust ) , crm 3 pltcm , bearing, radial ( cyl. ) , b / up spm 3, crm 3 bearing radial for back up roll, spm 3, crm 3 four row cyli , bearing, thrust ( tapered ) , b / up spm 3, crm 3 , bearing ( radial+ thrust ) for work roll, spm 3, crm 3 fourrow tapered roller bearing for spm 3 work total quantity : 185...
28925691 1. thrust bearing p no 1147.qty req.1 no ( s ) . 2. suction case p no 39003.qty req. 1 no ( s ) . 3. bawl stage casing part no. 39004.qty req. 1 no ( s ) . 4. auto transformer oil cooled 550v.qty req.1 no ( s ) ....
28519186 1) thrust bearing p no 1147. qty req 1 no(s). 2) impellar p. no. 39005. qty req 6 no(s). 3) bawl p o. 39004. qty req 6 no(s). 4) suction case p no 390031. qty req no(s). 5) pump couple p no 39029. qty req 1 no(s). 6) suction sleeve p no 39017....
27809517 procurement of spares for pullen pump , sand deflector / part no 25000 , oil seal / part no 25001 , pump shaft ( 5 stages ) / part no 25002 , suction case ( p 16 type ) / part no 25003 , bawl ( stage casing ) / part no 25004 , impeller / part no 25005 , stud for stage casing / part no 25008 , nut for stud / part no 25009 , neckring / part no 25010 , bush for stage casing / part no 25011 , bush for dol / part no 25013 , suction sleeve / part no 25017 , middle sleeve / part no 25021 , pump couple / part no 25029 , sleeve for dol / part no 25032 , cap screw for couple / part no 25033 , suction strainer / part no 25043 , cable wire ( 2r x 3cx95 sqmm ) / part no 1601 , key for motor coupling / part no 1602 , connecting piece / part no 1603 , cable gromate / part no 1606 , rotor sleeve lower / part no 1613 , t . b . plate with fiber / part no 1615 , motor base / part no 1619 , motor coupling / part no 1621 , stud for connecting piece / part no 1622 , drain plug connecting piece / part no 1623 , oil seal / part no 1624 , nut for upper stud / part no 1625 , upper stud / part no 1627 , upper housing / part no 1629 , bearing bush for upper / part no 1630 , bearing bush for lower / part no 1637 , lower housing / part no 1638 , thrust bearing complete / part no 1647 , rocker support / part no 1648 , p . c . d . cup / part no 1651 , screw for counter thrust / part no 1663...
27353318 part repairing of 2000 gpm rkb pump sl . no . 12972150006 including changing of thrust bearing make kirloskar , type rkb 250/46k , 3 stage located at quarry no . 02 under kathara colliery...
27353307 part repairing including changing of thrust bearing of 2000 gpm rkb pump , make kirloskar , type rkb 250/46k , 3 stage , sl . no . 12972150007 located at quarry no . 02 under kathara colliery...
26937175 part repairing including changing of thrust bearing of 2000 gpm rkb pump make kirlosker, type rkb 250/46k, 3 stage sl. no. 12972150006 located at quarry no. 02 under kathara colliery....
26389231 supplying & fitting 3 tonne capacity chain pulley, thrust bearing, sluice valve & n.r valve for 1 phase raw water pumping plant sitarampur under d. w. &. s. mechanical sub division, adityapur....
26364816 repair of submersible pump motor set ( near 18 camp pump house ) after taking out from site to workshop and reinstalling the same at site after repair under ge ramgarh cantt , repair of submesible pump motor set from borewell after disconnecting all pipes and fittings and take to workshop for repair and repair / replacment of following items: ( a ) taking out from borewell and lowering after repair 01 job ( b ) welding and cutting of existing pipe 01 job ( c ) transportation to workshop & back 01 job ( d ) motor rewinding 01 job ( e ) thrust bearing 01 no . ( f ) gun metal bush 01 no ( g ) shaft grinding 01 job ( h ) lead wire 06 rm ( j ) pump impeller work 01 job ( k ) coupling 01 no ( l ) coupling key 01 no ( m ) pump motor painting 01 job ( n ) mechanic charges 01 job...
25909295 part repairing & overhauling including changing of thrust bearing of 2000gpm rkb pump make kirlosker , type rkb 250/46k, 3 stage sl. no. 12972150008 located at quarry no. 03 under kathara colliery....
25622276 supply of spherical roller thrust bearing, size: 220 x420x 122...
24798139 supply of spherical roller thrust bearing , single row cylindrical roller bearing...
24503468 annual repair and maintenance of of electro and mechanical installations at b . m . airport , ranchi sh providing maintenance services for e and m installations of operational area and technical block for the year 2020 2022 , sub head i operation and maintenance man power requirement . providing operation and maintenance services of electrical & mechanical installations monthly at entire operational area includes old & new atc cum technical block , fire station , navaids , stp building , hangars ( for availing source of power supply only ) comprising glf systems , ccrs , 03 nos . dg sets upto 500 kva with amf panels , power supply distribution systems , transformers upto 630 kva , water pump sets , lifts , high mast towers , flood lights , street lights , perimeter road lights , fire hydrant system ( only operations ) , hvac vrv system ( only operations ) all internal & external e . i . works , old & new atc power houses , fire station , i / c 33 kv ht panel , all lt panels & feeder pillars , apfc panel , alcms , upss ( 2 nos x80 kva and 2 nos x180 kva ) including other minor ancillary & related installations covering the scope of operations , repairs & maintenance , attending faults / breakdowns rectifications , ensuring serviceability / satifactory working condition of the systems , preventive maintenance on daily / weekly / monthly / quarterly / half yearly / yearly basis , maintenance of records / documentation etc . as per scope of work given in special conditions and technical specifications of contract on all days including sundays & holidays . the services of dg sets , amf panels at power houses and the services of all other e & m installations shall be ensured round the clock ( ie . in three shifts daily , each shift of 8 hours ) as per specification and as required . ( minimum manpower engaged shall be as per special condition of contract and particular specification of contracts ) , ist year , ii nd year , sub head 2 miscellanious seruices testing bdv value of transformer oil in presence of aai representative , ist year , ii nd year , dehyderation and filtration of transformer oil at site including testing for bdv value after dehydration and filtration and submission of test reports etc . complete as required . , ist year , ii nd year , servicing , maintenance and testing of l & t make air circuit breaker up tol000a complete as required . , ist year , ii nd year , servrcing , maintenance and calibration of earth fault and over load relay with secondary injection kit etc . of 02 nos . ht panel of jyoti make comdlete as required . , ist year , ii nd year , servicing , maintenance and testing of 33 kv ht vaccum circuit breaker ofjyoti make etc . complete as required . , ist year , ii nd year , repair and rewinding of submersible pump motor upto 5 hp job includes transportation of motor , dismantling and rewinding with the same gauge insulated copper wire including replacement of all the internal worn out / defective parts i . e . bushes , impellers , sleeves , upper and lower bush sets , thrust bearings , oil seals , rotor grinding and balancing , assembling , testing , transportation etc . complete as required . , lifting and lowering of submersible pumps of various capacities ( upto 5 hp ) due to defect in existing pump on urgent basis within a short notice including connection of cable , jointing of cable etc with successful testing & commissioning complete as required . , repair and overhauling of amf panels i / c checking of control circuits , interlocking , checking of healthiness of all components including amf relays etc as complete and as per direction of eic ( faulty spares to be provided by aai ) , sub head 3 supply of general electrical materials as and when required . supply of flame retardant low smoke & halogen fr lsh pvc insulated industrial cables of following sizes single core fr lsh pvc insulated industrial grade copper conductor ( unsheathed ) flexible cables , 1100 volts conforming to is: 694 ( each roll of 90 mtrs ) , i core 1 . 5 sq . mm . , i core2 . 5 sq . mm . , i core 4 sq . mm . , supply of pvc insulated and fr pvc round sheathed , copper conductor ( flexible ) industrial cable , 1100 volts , conforming to is: 694 ( each roll of 100 mtrs ) , 3 core 2 . 5 sq . mm . , 3 core 4 sq . mm . , supply of 90 w led street light fittings cool white , supply of 3hp submersible pump set make ksb , model umai 100 2 . 2122 or equivalent , supply of wll mounted fans 300 mm sweep , supply of medium intensity aviation obstruction light for 230 v system , supply of following size xlpe insulated and pvc sheatheed , armoured aluminum conductor power cable of 1 . 1 kv grade conforming to is 7098 ( part 1 ) 1988 with upto date amendments . 3 . 5 x 185sq mm , 12v constant voltage converter drive for led signages 60w , 12v constant voltage converter drive for led signages 120w , led strip 0 . 2w x 144 per strip of i meter , sh:4 supply of airfield materials i / c glf supply of following glf items as per latest icao specifications , 200w 6 . 6 a holagen lamp runway lamp , 105 w 6 . 6 a bipin ( inset ) halogen lamp , 200 w 6 . 6 a elevated approach fiting lamp , runway larnp holder ( flate end tenninal ) , 6 sq . mm essna kit ( copper ) 5kv grade , 16 sq . mm 5 kv grade plug &recaptable ( essna kit ) ( copper ) , secondary 2 pin lead of 0 . 3 mtr length , two pin secondary plug assembly for papi ( 2 . 5 mtr long ) , base plate gaskets , led signage converter capable to drive led strip of 05w for ooerational area signages , led signage strip of 0 . 5w make osram or equivalent , led type taxi fitting as per latest icao standards , breakable coupling for glf light fittings , supply of scr / thyrister for nasu ccr , 85 rk 160 scr / thyrister for 7 . 5kw nasu make ccr , 250rk 160 scr / thyristor for 30kw nasu make ccr , supply of isolating transformer as per icao , isolating transformer200w 20 / 6 . 6 a , isolating transformer200w 6 . 6 / 6 . 6 a , isolating transformer 45w 20 / 6 . 6 a , isolating transformer 45w 6 . 6 / 6 . 6 a , isolating transformer 15 w 20 / 6 . 6a , isolating transformer 15 w 6 . 6 / 6 . 6a , isolating transformer 300w 6 . 6 / 6 . 6a , supply of lens , 360 clear inner lens / filters , 180 deg inner lens filters , 180 deg red lens filters , 180 deg green lens filters , 180 deg yellow lens / filter , ommi directionol blue lens suitable for mirl , 180 deg black sheild , 180 yellow filter ( convetional type ) , red filter for papi , red spreader lens for end light fiting , green spreader lens for threshold light fiting , 360 clear outer dome for hirl fitring , supply of airfield / runway cable , 1x6 sq . mm airfiled lieilrting cable , 1x16 sq . mm airfiled lieilrting cable , sub head 5 dsr works percentage above or below on the rates of dsr2018 ( cpwd ) electrical items worth totaling to rs . 15 , 00 , 000 . 00 as per requirement . ( note: the firm has to quote / upload the percentage above / below ( + / % ) on the quantity mentioned against this item directly in the form of multiplying factor in the rate coloumn as clarified below: for example: if desired to quote 5% above on sr 2018 rates , the rate column shall be filled as 1 . 05 . if desired to quote 3% below on sr 2018 rates , the rate column shall be filled as 0 . 97 . ) ...
23661848 supply of single row ball thrust bearing , single row roller bearing , double row self aligning roller bearing...
23297211 supply of spares 1 counter shaft & pinion sub assembly, part no. 07090010113 2 thrust bearing assembly, part no. 7090020004 3 bevel gear, part no. 0700005738t 4 inner counter shaft bushing, part no. 700048c102 5 outer counter shaft bushing, part no. 700048c102 6 oil flinger, part no. 0700005664t 7 piston wear ring seal, part no. 01063084703 for 4 . 1 / 4 standard head cone crusher....
23281445 supply of deep groove ball bearing 16005, deep groove ball bearing 6002, deep groove ball bearing 6022, deep groove ball bearing 6220, 4 point contact ball bearing qj 212, deep groove roller bearing 6211 2z, spindle bearing b7012 e.tpa.p4.ul, needle roller bearing nk 60/25, double row cyl.roller bearing nnu 4980bk.spb900, sph. roller bearing 22216e, sph. roller bearing 22218e, sph. roller bearing 22219e, sph. roller bearing 22220e, sph. roller bearing 21319 e, thrust needle roller bearing axk 3047, inner ring ir 35x40x17, inner ring ir 35x40x30, needle roller bearing nki 50/35, cyl. roller needle thrust bearing nkxr 40 z, taper roller bearing 32006 x, taper roller bearing 32009 x, thrust ball bearing 51107, thrust ball bearing 51148, sph. roller bearing 29317, inner ring ir 55x60x35, hinge head gar 12 uk,...
22946914 procurement of bearings , cylindrical roller thrust bearing no . az 9013535/ 81218 tv or eqvt . size: 90x135x35...
22583724 supply of bearing 1. spherical roller thrust bearing, size 180x300x73, skfno.29336 or eqvt 2. single row cylindrical roller bearing, size: 220x400x65, skf no nu244 or eqvt....
21815531 supply of double row taper roller bearing ‘eqvt. to timken no. hm256849/256810cd size: 300.038 (id) x 422.275 (cd) x 174.62s (width) spherical roller bearing eqvt. to skf 23076 cciw33 size: 380 (id) x 560 (od) x 135 (width) spherical roller bearing eqvt. to skf 23088 caiw33 size: 440 (id) x 650 (cd) x 157 (width) spherical roller thrust bearing eqvt. to skf 29352e size: 260 (id) x 420 (cd) x 95 width lock nut equivalent to skf no. hm3084 lock nut equivalent to skf no. hm3060 lock washer equivalent to skf no. ms3060...
21547698 supply of spares for crane assy (crane truck) model 2020 make imt thrust bearing pt. no. 60030116, bearing pt. no. 70055147, bearing pt. no. 70055148, bearing cone pt. no. 70055192, bearing cup pt. no. 70055193, bushing pt. no. 70143670, ball bearing pt. no. 70055202, turntable bearing pt. no. 71056308, cap screw pt. no. 72060774, seal kit pt. no. 9d141420, seal kit pt. no. 9d081012, remote handle assy pt. no. 51713384, retaining ring pt. no. 72661348, oil seal pt. no. 76393173, sheave pt. no. 60030082, set screw pt. no. 72060579. worm gear pt. no. 70056307 washer pt. no. 70143669 ...