Department Of Atomic Energy - Jharkhand

33567853 bids are invited for title1 earth work in excavation over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm. on plan ) including disposal of excavated earth lead up to 50m and lift up to 1.5 m, dispose earth to be level and neatly dressed complete as per the instruction of engineer in charge.all kinds of soil / soft rock / weathered rock 20 title2 supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 15 title3 surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto 1.5m all kinds of soil 500 title4 cleaning jungle including uprooting of rank vegetation, grass, brush wood, trees and sapling of girth upto 30cm. measured at a height of 1 m above ground level and removal of rubbish upto a distance of 2km out side the periphery of the area cleared by your own vehicle. 1000 title5 providing and laying in position plain cement concrete 1 / 2 / 4 ( 1 cement / 2 coarse / 4 graded stone aggregates 20 mm nominal size ) excluding the cost of centering, shuttering and cement san in foundation, footings, and bases of column as per specifications and drawings and direction of engineer in charge. 10 title6 providing and laying reinforced cement concrete work 1 / 1.5 / 3 ( 1 cement / 1.5 coarse sand / 3 graded stone aggregate using 20 mm down screened and washed ) including machine mixing, placing in position and mechanically vibrating in footing, column, plinth beam up to plinth level and like including preparing of the top surface finishing curing ecomplete in all respects as per specification and direction. 5 title7 providing and laying reinforced cement concrete work 1 / 1.5 / 3 ( 1 cement / 1.5 coarse sand / 3 graded stone aggregate using 20 mm down screened and washed ) including machine mixing, placing in position and mechanically vibrating in beams, suspended floor landing, balconies, lintel etc.to any floor and any where and like including preparing of the top surface finishing curing complete in all respects as per specification and direction. 10 title8 hire and labour charges for providing and fixing straight shuttering for concrete works to anywhere at any floor ( including staging ) including strutting, propping etc. and removal of form or striking out after completion of works as directed and specified by the engineer in charge a ) foundations, footings, bases of columns plinth beam etc 10 title9 b ) suspended floors, roofs, landings, balconies, shelves etc. 35 title10 c ) lintels, beams, cantilever etc. 25 title11 steel reinforcement ( for reinforced cement concrete work ) including transporting, decoiling, straightening, derusting, placing, cutting to requisite length, hooking, bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection including removal of loose rust and applying a coat of cement wash if necessary complete in all respects as per drawing and at any floor as directed. 500 title12 brick work with bricks of class designation 75 in foundation and plinth in cement mortar 1 / 6 ( 1 cement / 6 coarse sand ) . 5 title13 brick work with bricks of class designation 75 in superstructure with cement mortar 1 / 6 ( 1 cement / 6 coarse sand ) including all materials, labour, scaffolding, racking out joints, curing as per specification and direction of the engineer in charge. 10 title14 half brick masonry with bricks of class designation 75 in super structure above plinth level upto floor v level.cement mortar 1 / 4 ( 1 cement / 4 coarse sand ) . 10 title15 providing and fixing factory made solid core, commercial flush door shutters non decorative type, core of block board construction with well seasoned chemically treated timber of moisture content, not exceeding 12 per cent and side styles, top and bottom rails of main width as per i.s. code, well seasoned hard wood chemically treated and well matched commercial ply veneering with vertical grains on cross bends on both faces of shutters, hot pressed and banded with phenol formaldehyde synthetic resin conforming to i.s. / 2202 ( part –i ) / 1930 a ) 35mm thick shutter with 100mm oxidized s.s. butt hinges with necessary screws for double or single leaf shutters complete. 12 title16 providing and fixing aluminum. ( heavy type ) sliding door bolts with nuts and screws etc. complete.a ) 300 x 16mm 6 title17 providing and fixing anodized aluminum tower bolt ( heavy type ) including necessary screws etc. complete. 150 x 10mm 8 title18 providing and fixing bright finished brass casement window fasteners of minimum weight 200 grams to side hung steel windows with necessary welding and machine screws etc. complete. 10 title19 providing and fixing bright finished brass peg stays 300mm long of minimum weight 330 grams. to side hung steel windows with necessary welding and machine screws etc. complete. 12 title20 providing and fixing anodized aluminum tower bolt including necessary screws etc. complete.250 x 10mm 8 title21 providing and fixing anodized aluminum door handle including necessary screws etc. complete.a ) 125mm 12 title22 24 mm thick factory made pvc door shutters made of styles and rails of a upvc hollow section of size 59x24 mm and wall thickness 2 mm ( plus minus 0.2 mm ) with inbuilt edging on both sides.the styles and rails mitred and joint at the corners by means of m.s. galvanised / plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. the styles of the shutter reinforced by inserting galvanised m.s. tube of size 20x20 mm and 1 mm ( plus minus 0.1 mm ) wall thickness. the lock rail made up of h section, a upvc hollow section of size 100x24 mm and 2 mm ( plus minus 0.2 mm ) wall thickness, fixed to the shutter styles by means of plastic / galvanised m.s. u cleats the shutter frame filled with a upvc multi chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( plus minus 0.1 mm ) wall thickness. the panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised m.s. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of engineer in charge. ( for w.c. and bathroom door shutter ) . 4 title23 providing and fixing structural steel work reveted, bolted or welded in built up sections, trusses and framed work , including cutting hoisting, fixing in position and applying a priming coat of approved steel primer. 250 title24 steel work in built up tubular trusses including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete. a ) hot finished welded type tubes. 200 title25 brick on edge flooring with bricks of class designation 7.5 on a bed of12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks. 10 title26 providing and laying for 40mm thick cement concrete in flooring, in ratio 1 / 2 / 4 ( 1 cement / 2 coarse sand / 4 stone aggregate ) finished with a floating coats of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete including cost of all materials but excluding cost of cement. 5 title27 providing & fixing for laying chequred precast concrete portico tiles of size 300mm x 300mm durastone heavy duty vitrified tiles of color back ground ( make endura / somany ) of size as required in footpath and courtyard, etc. laid on a bed of 20mm thick cement mortar 1 / 4 ( 1 cement / 4 coarse sand ) finishing with flush pointing in white / color cement as required. 75 title28 providing and laying vitreous floor tiles in different sizes ( thickness to be specified by the manuaturer ) with water absorption less than 0.08% and conforming to is 15622 oif aproved make in all colours and shades laid on 20mm thick cement mortar 1 / 4 ( 1 cement / 4 coarse sand ) jointing wth grey cement slurry at the rate of 3.3kg / sqm including grouting the joints with white cement an matching pigments etc complete. size of tile 600 x 600 mm ( somany / kajaria ) 480 title29 providing and fixing pre coated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm ( plus 0.05 % ) total coated thickness with zinc coating 120grams per sqm as per is 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineerin charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55 mm ) with epdm seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 150 title30 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is 13592 type a, including jointing with seal ring conforming to is 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes.110 mm diameter 15 title31 providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( plus 0.05 % ) total coated thickness, zinc coating 120 grams per sqm as per is 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws complete. a ) ridges plain ( 500 600mm ) 75 title32 b ) gutter ( 600 mm over all girth ) 30 title33 12 mm cement plaster of mix 1 / 6 ( 1 cement / 6 coarse sand ) 200 title34 providing neat cement punning about 1.5mm thick in wall, dado, window sills, plinth etc. and like at any level to anywhere as directed and specified by the engineer in charge. 50 title35 white washing with lime to give an even shade new work ( three or more coats ) . 400 title36 supplying and painting with synthetic enamel paint / aluminum paint of approved brand and manufacture two or more coats in new work..two or more coats in new work. 125 title37 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.m including cutting the patches in proper shape, raking out joints and preparing and plastering ( 1 / 4 ) the surface of the walls complete shade including cost of all materials, labours, scaffolding, tools and tackles , disposal of rubbish to the dump yard with in 50 m lead excluding the cost of cement. 50 title38 providing and fixing of glass panes, with putty and nails wherever necessary glass panes 4mm thick. 15 title39 removing white or color wash snowcem / distemper by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 150 title40 finishing walls with premium acrylic smooth exterior paint ( weather coat ) with silicone additives of required shade new work ( two or more coats applied at the rate 1.43 ltr / 10 sqm over and including priming coat of exterior primer applied at the rate of 2.20 kg / 10 sqm ) 350 title41 demolishing of cement conc. including disposal of material within 50m lead in the ratio 1 / 3 / 6 or richer mix 10 title42 dismantling of old brick work including stacking of serviceable material and disposal of unserviceable material within 50m lead.in cement mortar. 10 title43 dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. 300 title44 transport of above materials by physical / mechanical means within 2km. 1 title45 extra for marking of structural steel work required to be re erected ( cutting, hoisting, welding etc. to be done if required ) . 500 title46 dismantling of old plaster or skirting raking out joints and cleaning the surface of plaster including disposal of rubbish to the dumping yard with 50 mtr. lead. 12 title47 providing and fixing white vitreous china wash basin with c.i. / m.s. brackets, 15mm c.p.brass pillar tap ( single ) 32mm c.p. brass waste of standard pattern, including pvc waste pipe and pvc connector pipe including painting of fitting and brackets , cutting and making good the walls wherever required.a ) wash basin size 550 x 400mm.make hindware / parryware / roca 2 title48 providing and fixing stainless steel a isi304 ( 18 / 8 ) kitchen sink as per is 13983 with c.i.brackts and stainless steel plugs 40mm including making all connection excluding cost of fittings with drain board.size 1040x510x250mm make ( hindware / parryware / roca / cera. ) 2 title49 providing and fixing 32 mm dia. p.v.c. flexible waste pipes for sinks and wash basins. 6 title50 providing and fixing soil, waste and vent pipes 5 title51 providing and refixing of 1st quality tata gindal make g.i.pipe removing of old g.i.pipes and complete with g.i.fittings and clamp including cutting and making good the wall etc. a ) 15mm dia nominal bore 15 title52 b ) 20mm dia. nominal bore 15 title53 providing and fixing gun metal gate valve with c.i. wheel of approved quality ( screwed end ) a ) 25 mm nominal bore 1 title54 b ) 20 mm nominal bore 1 title55 c ) 15 mm nominal bore 6 title56 providing and fixing gun metal non return valve of approved quality ( screwed end ) 25mm nominal bore a ) horizontal 1 title57 b ) vertical 1 title58 providing and fixing heavy duty c.p brass bib cock of 15mm nominal bore as per approved sample ( brand jaquar / omco ) . 10 title59 providing and fixing heavy duty c.p brass stop cock ( concealed ) of 15mm nominal bore as per approved sample. ( brand jaquar ) . 6 title60 providing, laying and jointing glazed stone ware pipes 150mm dia grade – a with stiff mixture of cement mortar in the proportion of 1 / 1 ( 1 cement / 1 fine sand ) including testing of joints etc. complete. excluding the cost of cement. 10 title61 providing, laying cement concrete 1 / 5 / 10 ( 1 cement / 5 coarse sand / 10 stone aggregate of 40mm size ) all round s.w.pipes including bed concrete as per standard design . 150mm dia s.w. pipe 10 total quantity : 5781...

Department Of Atomic Energy - Jharkhand

31863835 bids are invited for miscellaneous civil work title1 earth work in excavation ( exceeding 30cm in depth 1.5 mtr. in width or 10 sq.m. on plan ) by mech / manual means including dressing of sides and ramming of bottoms, lift upto 1.5 mtr including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 mtr. all kinds of soil title2 surface dressing of the ground ( including removing vegetation and in equalities not exceeding 15 cm deep ) and disposal of rubbish, lead up to 50 m and lift upto 1.5m all kinds of soil title3 cleaning jungle including uprooting of rank vegetation, grass, brush wood, trees and sapling of girth upto 30cm. measured at a height of 1 m above ground level and removal of rubbish upto a distance of 2km out side the periphery of the area cleared by your own vehicle. title4 providing and laying in position plain cement concrete in the ratio 1 / 3 / 6 ( 1 cement / 3 coarse / 6 graded stone aggregates 20 mm nominal size ) excluding the cost of centering, shuttering and cement san in foundation, footings, and bases of column as per specifications and drawings and direction of engineer in charge. title5 white washing with lime to give an even shade new work ( three or more coats ) . title6 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level in the ratio 1 / 2 / 4 ( 1 cement , 2 coarse sand , 4 graded stone aggregate 20mm nominal size ) title7 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work above plinth level in the ratio 1 / 1.5 / 3 ( 1 cement , 1.5 coarse sand , 3 graded stone aggregate 20mm nominal size ) title8 providing and laying for fixing steel reinforcement for reinforced cement concrete work including transporting , decoiling, straightening, cutting, derusting bending, placing in position at all height and binding with binding wire etc. complete as per drawing, specification and instruction of the engineer in charge. title9 brick work with bricks of class designation 75 in foundation and plinth in cement mortar ratio 1 / 6 ( 1 cement , 6 coarse sand ) . title10 brick work with bricks of class designation 75 in superstructure with cement mortar in the ratio 1 / 6 ( 1 cement , 6 coarse sand ) including all materials, labour, scaffolding, racking out joints, curing as per specification and direction of the engineer in charge. title11 12 mm cement plaster of mix in the ratio1 / 6 ( 1 cement . 6 coarse sand ) . title12 providing neat cement punning about 1.5mm thick in wall, dado, window sills, plinth etc. and like at any level to anywhere as directed and specified by the engineer in charge. title13 removing dry / oil bound distemper by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete title14 removing white or color wash snowcem / distemper by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. title15 providing and laying for / plastic emulsion of approved brand ( asian paints / berger 1st quality ) and manufacturer over two coat of approved primer after preparation of surface properly to give an even shade including cost of labour and as per specification and direction of engineer in charge. one or more coat on old work till give an even shade. title16 finishing walls with waterproofing cement paint of approved brand and manufacture and of required shade to give an even shade.new work ( three or more coats ) title17 half brick masonry with bricks of class designation 75 in super structure above plinth level upto floor v level.cement mortar in the ratio 1 / 4 ( 1 cement, 4 coarse sand ) . title18 supplying and painting with synthetic enamel paint / aluminum paint of approved brand and manufacture two or more coats in new work..two or more coats in new work. title19 demolishing of cement conc. including disposal of material within 50m lead in the ratio1 / 3 / 6 or richer mix title20 dismantling of old brick work including stacking of serviceable material and disposal of unserviceable material within 50m lead.in cement mortar. title21 providing and laying for fixing and sizing of any sizes of cgi / colour corrugated sheets of 0.63mm thick with ridges and wind tie on roof at any height including scaffolding and etc. all complete as per instruction of engg. in charge. title22 dismantling of old plaster or skirting raking out joints and cleaning the surface of plaster including disposal of rubbish to the dumping yard with 50 mtr. lead. title23 providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete. title24 providing and laying for 40mm thick cement concrete in flooring, in ratio 1 / 2 / 4 ( 1 cement, 2 coarse sand, 4 stone aggregate ) finished with a floating coats of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete including cost of all materials but excluding cost of cement. title25 grading of roof for water proofing treatment with cement concrete in the ratio 1 / 2 / 4 ( 1 cement , 2 coarse sand , 4 graded stone aggregate 12mm nominal size ) mix with sika top seal and sikadur 32 in appropriate proportion. title26 providing and laying for fixing g.i. pipes complete with g.i. fittings and clamps, including cutting and making good the walls etc. ( internal work ) free of cost 15mm dia nominal bore title27 b ) 20mm dia nominal bore title28 providing and fixing structural steel work reveted, bolted or welded in built up sections, trusses and framed work , including cutting hoisting, fixing in position and applying a priming coat of approved steel primer. title29 providing and laying hire and labour rate for fixing centering shuttering for concrete works to anywhere at any level ( including staging ) including strutting, propping etc. and removal of form or striking out after completion of works as directed and specified by the engineer in charge. ( material for shuttering to supplied by the contractor ) a ) foundations, footings, bases of columns plinth beam etc title30 b ) suspended floors, roofs, landings, balconies, shelves etc. title31 providing and laying decorated color back ground spartek / somany / nitco vitrified ceramic tiles of size 600mm x 600mm x 10 mm thick or any required tiles in floorings, treads do etc. laid on a bed of 10mm thick cement mortar in the ratio 1 / 3 ( 1 cement , 3 coarse sand ) finishing with flush painting in white / color cement as required. title32 providing & fixing for laying chequred precast concrete portico tiles of size 300mm x 300mm durastone heavy duty vitrified tiles of color back ground ( make endura / somany ) of size as required in footpath and courtyard, etc. laid on a bed of 20mm thick cement mortar in the ratio1 / 4 ( 1 cement , 4 coarse sand ) finishing with flush pointing in white / color cement as required. title33 providing and laying for laying decorated colour back ground ceramic tiles of reqd. size in wall / floor laid on 10mm thick cement mortar in the ratio 1 / 3 ( 1 cement , 3 coarse sand ) finishing with flush painting in white / color cement as required. tiles should be standard quality of spartek / somany. title34 providing and laying for finishing walls with advanced anti alagal weather proof emulsion paint brand apex ultima ( make asian paints ) approved brand and manufacture and of required shade to give an even shade over 2 ( two ) coats professional primerwater thinnable ( make asian paints e7 ) . consumption rate2.50litre / sq.m.new work ( three or more coats ) title35 providing and fixing factory made solid core, commercial flush door shutters non decorative type, core of block board construction with well seasoned chemically treated timber of moisture content, not exceeding 12 per cent and side styles, top and bottom rails of main width as per i.s. code, well seasoned hard wood chemically treated and well matched commercial ply veneering with vertical grains on cross bends on both faces of shutters, hot pressed and banded with phenol formaldehyde synthetic resin conforming to i.s. / 2202 ( part i ) / 1930. a ) 35mm thick shutter with 100mm oxidized s.s. butt hinges with necessary screws for double or single leaf shutters complete. title36 colour washing such as yellow, green, blue or buff to give an even shade new work ( two or more coats ) with a base coat of white washing with lime title37 providing and applying one coat of cement primer of approved brand on wall including cost of all materials, labour, scaffolding, tools and tackles etc. complete as per direction of engineer in charge. title38 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.m including cutting the patches in proper shape, raking out joints and preparing and plastering in the ratio 1 / 4 the surface of the walls complete shade including cost of all materials, labours, scaffolding, tools and tackles , disposal of rubbish to the dump yard with in 50 m lead excluding the cost of cement. title39 providing and fixing in position pedestal european type water closet white glazed vitreous chinaware with seat and lid ( white ) hind ware make or approved brand and quality, 10 litres capacity low level white pvc flushing cistern manually controlled device ( handle lever ) and c.p. flush bend with fitting and brackets, conforming to is 7231 including assembling all the parts in position and satisfactory testing, 32mm diameter pvc flush pipe with fittings. ( the rate quoted shall be satisfactory operation and leak proof joints ) .make hindware title40 providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin with all fittings of 430x260x350 mm or 340x410x265 mm sizes respectively.make hindware title41 providing and fixing low level 10 litres capacity white p.v.c. flushing cistern with manually controlled device conformed to is 7231 with all fittings and fixtures complete make hindware title42 providing and fixing white solid plastic seat with lid for e.w.c. pan complete. title43 providing and fixing 32 mm dia. p.v.c. flexible waste pipes for sinks and wash basins. title44 providing and fixing heavy duty c.p brass bib cock of 15mm nominal bore as per approved sample ( brand jaquar ) . title45 providing and fixing heavy duty c.p brass stop cock ( concealed ) of 15mm nominal bore as per approved sample. ( brand jaquar ) . title46 supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. title47 providing and placing on terrace polyethylene water storage tank isi 12701 with cover and suitable locking arrangement and making necessary holes for inlet and outlets and overflow pipe but without fittings and base supports for tank. title48 providing and fixing anodized aluminum tower bolt including necessary screws etc. complete.250 x 10mm title49 providing and fixing anodized aluminum door handle including necessary screws etc. complete.a ) 125mm title50 providing and fixing anodized aluminum hanging floor door stopper ( twin robber ) with necessary screw etc. complete. title51 providing and fixing aluminum. ( heavy type ) sliding door bolts with nuts and screws etc. complete.a ) 300 x 16mm title52 providing and fixing anodized aluminum tower bolt ( heavy type ) including necessary screws etc. complete. 150 x 10mm title53 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is 13592 type a, including jointing with seal ring conforming to is 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes.110 mm diameter title54 24 mm thick factory made pvc door shutters made of styles and rails of a upvc hollow section of size 59x24 mm and wall thickness 2 mm ( 0.2 mm ) with inbuilt edging on both sides.the styles and rails mitred and joint at the corners by means of m.s. galvanised / plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. the styles of the shutter reinforced by inserting galvanised m.s. tube of size 20x20 mm and 1 mm ( 0.1 mm ) wall thickness. the lock rail made up of h section, a upvc hollow section of size 100x24 mm and 2 mm ( 0.2 mm ) wall thickness, fixed to the shutter styles by means of plastic / galvanised m.s. u cleats the shutter frame filled with a upvc multi chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( 0.1 mm ) wall thickness. the panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised m.s. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of engineer in charge. ( for w.c. and bathroom door shutter ) . title55 providing and fixing bright finished brass casement window fasteners of minimum weight 200 grams to side hung steel windows with necessary welding and machine screws etc. complete. title56 providing and fixing of glass panes, with putty and nails wherever necessary glass panes 4mm thick. title57 providing and fixing bright finished brass peg stays 300mm long of minimum weight 330 grams. to side hung steel windows with necessary welding and machine screws etc. complete. title58 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic molded frame of approved make and shade with 6 mm thick hard board backing rectangular shape 453x357 mm. title59 providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40 mm long screws, rawl, plugs etc., complete. title60 providing and fixing soil, waste and vent pipes sand cast iron s&s pipe as per is 1729 title61 brick on edge flooring with bricks of class designation 7.5 on a bed of12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks a ) horizontal title62 providing and fixing gun metal non return valve of approved quality ( screwed end ) 25mm nominal bore a ) horizontal title63 b ) vertical title64 providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white p.v.c.automatic flushing cistern, with fittings, standard size g.i. / pvcflush pipe for back and front flush with standard spreader pipes withfittings, g.i clamps and c.p. brass coupling complete, includingpainting of fittings and cutting and making good the walls and floorsetc. wherever required single squatting plate with 5 litre p.v.c. automatic flushing cistern. title65 providing and fixing white vitreous china wash basin with c.i. / m.s. brackets, 15mm c.p.brass pillar tap ( single ) 32mm c.p. brass waste of standard pattern, including pvc waste pipe and pvc connector pipe including painting of fitting and brackets , cutting and making good the walls wherever required.a ) wash basin size 550 x 400mm. title66 providing & fixing white vitreous china water closet squatting pan ( indian type ) along with s or p trap including dismantling of old wc seat and s or p trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i / c malba, all complete as per the direction of engineer in charge.orissa pattern w.c pan of size 580x440 mm title67 supply and stacking of good earth at site including carriage up to 5 km ( earth measured in stacks will be reduced by 20% for payment ) title68 supply and stacking of good sludge at site including carriage up to 5 km 23.4.1 screened through sieve of i.s. designation 20 mm title69 providing and supplying the following manpower for repair of chajja, facia, roof top coping window sill, toilet & trap repairing, w.c.pan repairing, kitchen sink repairing, a.c. hole closing, small non measurable plastering , balcony railing repairing, grill fixing, hand rail fixing, door frame fixing / dismantling as directed by engg in charge.skilled 3no.unskilled 5 no. title70 providing plant budded rose ( h.t. variety ) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm earthen pot. title71 supply of good quality earthen pot ( gamla ) at site a ) earthen pot 10 inch size title72 b ) earthen pot 12 inch size title73 supply of fertilizers, pesticides & fungicides at site. a ) d a p title74 b ) urea ( neem coated ) title75 c ) bone meal title76 d ) mustered oil cake title77 supplying and stacking of seasonal seedling / cutting at site of work well developed and healthy free from disease in per tray and each per tray having 100 nos plants as per direction of the officer in charge. a ) calendula double title78 b ) chrysanthemum double title79 c ) dahlia double title80 d ) marigold inca hybrid title81 e ) pansy hybrid title82 f ) petunia hybrid title83 g ) aster dwarf title84 h ) kochia title85 i ) portulaca hybrid title86 j ) sunflower dwarf title87 k ) vinca hybrid...

East Central Railway - Jharkhand

30928257 auction sale of disposal of 4nos. abandoned building / structure at phulwaritand such as ( 1 ) lot no.kth / 14 / w / 21, brick work qty=44891nos.=115.70m3, rcc=0.8432mt=15.50m3, wooden door=2nos.=0.090mt, steel section=0.450mt, aluminium window=8nos=0.024mt, location plje east cabin, ( 2 ) lot no.kth / 15 / w / 21, brick work qty=9913nos.=25.55m3, rcc=0.2828mt=5.20m3, steel door=4nos.=0.240mt, steel window=4nos=0.160mt, location plje east cabin battery room, ( 3 ) lot no.kth / 19 / w / 21, brick work qty=45280nos.=116.70m3, rcc=0.8432mt=15.50m3, wooden door=2nos.=0.090mt, aluminium glaged window=7nos=0.021mt, location plje west cabin, ( 4 ) lot no.kth / 16 / w / 21, brick work qty=10000nos.=25.775m3, rcc=0.2856mt=5.25m3, steel door=4nos.=0.240mt, steel window=4nos=0.160mt, location plje west cabin battery room, delivery by lot basis ( qty, shown above are approx in broken / damage condition ) note: 1. dismantling is permitted up to ground level only. below ground level does not be permitted. cutting is permitted. due care to be taken by the bidder / purchaser to avoid the unwanted misshapes at work spots. they should ensure to keep a safety banner around the work spot. 2. only after removing / clearing the bricks machinery rubbish from the spot, the delivery of iron metal will be effected....

East Central Railway - Jharkhand

30928256 auction sale of disposal of 6nos. abandoned building / structure at katrasgarh such as ( 1 ) lot no.kth / 9 / w / 21, brick work qty=45978nos.=118.50m3, rcc=0.8568mt=15.75m3, wooden door=2nos.=0.090mt, aluminium glaged window=7nos=0.021mt, location kth east cabin, ( 2 ) lot no.kth / 10 / w / 21, brick work qty=10631nos.=27.40m3, rcc=0.2382mt=4.38m3, steel door=3nos.=0.180mt, steel window=2nos=0.080mt, location kth east cabin battery room, ( 3 ) lot no.kth / 20 / w / 21, brick work qty=44115nos.=113.70m3, rcc=0.826mt=15.19m3, wooden door=2nos.=0.090mt, steel section=0.500mt, aluminium glaged window=7nos=0.021mt, location kth west cabin, ( 4 ) lot no.kth / 11 / w / 21, brick work qty=10631nos.=27.40m3, rcc=0.238mt=4.375m3, steel door=3nos.=0.180mt, steel window=2nos=0.080mt, location kth west cabin battery room, ( 5 ) lot no.kth / 12 / w / 21, brick work qty=38000nos.=98m3, rcc=0.6732mt=12.375m3, wooden door=2nos.=0.090mt, steel section=0.500mt, aluminium glaged window=6nos.=0.018mt, location pre weighment cabin katrasgarh, ( 6 ) lot no.kth / 13 / w / 21, brick work qty=10630nos.=27.00m3, rcc=0.2377mt=4.37m3, steel door=3nos.=0.180mt, steel window=2nos=0.080mt, location kth preweighment cabin battery room, delivery by lot basis ( qty, shown above are approx in broken / damage condition ) note: 1. dismantling is permitted up to ground level only. below ground level does not be permitted. cutting is permitted. due care to be taken by the bidder / purchaser to avoid the unwanted misshapes at work spots. they should ensure to keep a safety banner around the work spot. 2. only after removing / clearing the bricks machinery rubbish from the spot, the delivery of iron metal will be effected....

East Central Railway - Jharkhand

30928255 auction sale of disposal of 4nos. abandoned building / structure at sijua such as ( 1 ) lot no.kth / 5 / w / 21, brick work qty=43534nos.=112.20m3, rcc=0.7956mt=14.625m3, wooden door=2nos.=0.090mt, steel section=0.450mt, wooden glass window=7nos=0.070mt, location sja east cabin, ( 2 ) lot no.kth / 6 / w / 21, brick work qty=10398nos.=26.80m3, rcc=0.238mt=4.375m3, steel door=3nos.=0.180mt, steel window=4nos=0.160mt, location sja east cabin battery room, ( 3 ) lot no.kth / 7 / w / 21, brick work qty=44418nos.=114.48m3, rcc=0.8263mt=15.19m3, wooden door=2nos.=0.090mt, steel section=0.500mt, wooden glass window=7nos=0.070mt, location sja west cabin, ( 4 ) lot no.kth / 8 / w / 21, brick work qty=9972nos.=25.70m3, rcc=0.2192mt=4.030m3, steel door=3nos.=0.180mt, steel window=4nos=0.160mt, location sja west cabin battery room, delivery by lot basis ( qty, shown above are approx in broken / damage condition ) note: 1. dismantling is permitted up to ground level only. below ground level does not be permitted. cutting is permitted. due care to be taken by the bidder / purchaser to avoid the unwanted misshapes at work spots. they should ensure to keep a safety banner around the work spot. 2. only after removing / clearing the bricks machinery rubbish from the spot, the delivery of iron metal will be effected....

East Central Railway - Jharkhand

30928252 auction sale of disposal of 4nos. abandoned building / structure at bansjora such as ( 1 ) lot no.kth / 1 / w / 21, brick work qty=61343nos.=158.10m3, rcc=0.7956mt=14.625m3, wooden door=2nos.=0.090mt, steel section=0.5mt, aluminium glass window=7nos=0.021mt, location bzs east cabin, ( 2 ) lot no.kth / 2 / w / 21, brick work qty=10414nos.=26.840m3, rcc=0.238mt=4.375m3, steel door=3nos.=0.180mt, steel window=4nos=0.160mt, location bzs east cabin battery room, ( 3 ) lot no.kth / 3 / w / 21, brick work qty=41524nos.=107.02m3, rcc=0.7648mt=14.06m3, wooden door=2nos.=0.090mt, steel section=0.450mt, wooden glaged window=7nos=0.070mt, location bzs west cabin, ( 4 ) lot no.kth / 4 / w / 21, brick work qty=10414nos.=26.840m3, rcc=0.238mt=4.375m3, wooden door=3nos.=0.135mt, wooden glass window=6nos=0.060mt, location bzs west cabin battery room, delivery by lot basis ( qty, shown above are approx in broken / damage condition ) note: 1. dismantling is permitted up to ground level only. below ground level does not be permitted. cutting is permitted. due care to be taken by the bidder / purchaser to avoid the unwanted misshapes at work spots. they should ensure to keep a safety banner around the work spot. 2. only after removing / clearing the bricks machinery rubbish from the spot, the delivery of iron metal will be effected....

Jawahar Vidya Mandir - Jharkhand

29271823 tender for dismantling of old steel window , supply and fixing by two track upvc sliding window , 225 number in jvm premises...

Jawahar Vidya Mandir - Jharkhand

28967330 tender for dismantling of old steel window, supply and fixing by two track upvc sliding window, 225 number in jvm premises....

Military Engineer Services - Jharkhand

25613608 provision of room for laundry including equipments under ge dipatoli 1 excavation in trenches n exc 1.5 m wide n exc 1.5 m deep and getting out in soft / loose soil for foundation etc or for shaft, wells, manholes etc n exc 10 sqm on plan and not exc 1.5 m in depth and getting out. complete all as specified and directed. 2 removing excavated material to a distance n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed. 3 returning, filling in including spreading, leveling, watering and well ramming in layers n.exc.25 cm complete all as specified and directed. 4 m&l cement concret ( 1:4:8 ) type d 2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed. 5 m&l reinforced cement concrete m 25 ( design mix ) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified. n 6 m&l reinforced cement concrete m 25 ( design mix ) as in columns, pillars, piers, posts and struts complete all as specified and directed. 7 m&l reinforced cement concrete in cement concrete m 25 ( design mix ) as in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified. n 8 m&l reinforced cement concrete m 25 ( design mix ) as in slabs supported on walls, beams and columns , in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified. 9 m&l precast cement concrete type b 1 ( 1:2:4 ) using 20mm graded stone aggregates, as in man hole cover slabs, shelves, and similar work set in cm ( 1:4 ) .complete all as specified and directed. 10 use and waste of formwork to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions surfaces finished fair as per clause 4.11.16.2 ( a ) of ssr part i complete all as specified. n 11 use and waste formwork to flat sides and soffits of floor or roof beams, beam haunchings, girders, bresumers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc. surfaces finished fair complete all as specified. n 12 use and waste of formwork to fair surfaces of sides of concrete foundations, footings, bases of columns , raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or to batter surfaces finished fair in forms complete all as specified. n n 13 use and waste of form work to flat soffits of suspended slabs, floor slabs, landings and similar work; not exceeding 200 mm thick ( horizontal or sloping ) surfaces finished fair in forms complete all as specified. n 14 use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs sides of rcc / pcc bands in walls , horizontal or sloping and similar work exc 10cm but n exc 20 cm wide, surfaces finished fair in forms complete all as specified. 15 m&l mild steel deformed or twisted bars ( tmt ) 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.90 mm dia. or higher complete all as specified. n 16 m&l mild steel deformed or twisted bars ( tmt ) 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.90 mm dia. or higher complete all as specified. n 17 m&l mild steel bars ( tmt deformed / twisted ) 8mm dia. and over up to and including 10 mm dia. in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.90 mm dia. or securing with clips complete all as specified. 18 m &l for brickwork with sub class b old size bricks, straright or corved on plan exc 6m mean radius built in cement mortar ( 1:6 ) complete all as specified and as directed. 19 m&l brickwork with subclass b old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed. 20 supply only liquid water proofing compound complete all as specified and directed. 21 m&l roof treatment for non approachable roof complete all as specified and directed comprising of followings: ( i ) rendering 10mm thick in cement mortor ( 1:3 ) mixed with liquid water proofing compound finished the surface fair and even. ( ii ) applying evenly a coat of bitumen primer @ 0.30 kg / sqm. ( iii ) applying app modified polymeric membrane over the bitumen coat surface , weight not less than 3.20 3.50 kg / sqm and over lap 100mm and sealed by torch application as per manufacture insteructions. ( iv ) applying a coat of aluminium paint @ 200 gm / sqm in two coats over polymeric membrene. 22 surface dressing in soft / loose soil n exc 15 cm deep trimming of natural ground ( removing vegetation / shurbs / brushwood. undergrowth and carring away rubbish to a distance of not exc 50 metre complete all as specified and directed. 23 m&l sand filling under floors or in foundation including watering and consolidation ( with lead of 50 m. for sand ) complete all as specified and directed. 24 m&l moorum / red bajri filling in floors or pavings, laid in floors n.exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed. 25 m&l for 100mm thickpcc ( 1:4:8 ) type d 2 using 40mm graded stone aggregate as in sub base complete all as specified and directed. 26 m&l for 75 mm thick pcc 1:3:6 type c 2 using 40mm graded stone aggregates, as in plinth protection and path etc finished cement concrete surface even and smooth without using extra cement all as specified. 27 m&l machine cut kota stone slab flooring 18 20 mm thick set over and including 15mm thick screed base in cm ( 1:6 ) , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beewax polishing complete all as specified and directed. 28 all as per item no 27 but here in before as in skirting set over and including 10mm thick cement plaster in cm 1:6 complete all as specified and directed.. 29 m&l white marble stone slab flooring 18 20 mm thick set over and including 15mm thick cement sceed base in cm 1:6 laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beewax polishing complete as a boarder in the kota stone floorig all as specified and directed. 30 m&l machine cut cuddapa stone slab 20 25 mm thick, laid over 15mm thick cm ( 1:6 ) cement screed base, laid and jointed with grey ement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed. 31 m&l rendering 15 mm thick on fair faces of brick work or concrete surfaces , in cement and sand mortar 1:6 , top surfaces finished even and smooth without using extra cement complete all as specified n n 32 m&l rendering 15 mm thick on fair faces of brick work or concrete surfaces , in cement and sand mortar 1:4, mixed with using liquid water proofing compound complete all as specified ) , top surfaces finished even and smooth without using extra cement complete all as specified and directed. nnote : wpc measured and paid separately n 33 m&l rendering 10mm thick in cement mortar i:3 on fair face of cement concrete on ceiling, finished surface even and smooth without using extra cement complete all as specified n 34 m&l applying three coat of white wash on newly plastered surfaces of walls including washing floors, cleaning glass, joinery, electrical fittings, wiring etc. , of drops and splashes complete all as specified . 35 m&l two coats distempering with cement base paint , white or tinted over a coat of cement base primer on new surfaces of walls including washing floors, cleaning glass, joinery, electrical fittings, wiring etc. , of drops and splashes complete all as specified . n n 36 m&l preparation of new plastered or unplastered surafces of ceilings and applying three coats of white wash including washing floors, cleaning glass, joinery, electrical fittings, wiring etc. , of drops and splashes complete all as specified . n n 37 m&l for cement concrete 1:2:4 type b 1 ( using 20mm graded stone aggregate ) as in bed block for hold fast & filling in pressed steel door frame complete all as specified . 38 m&l for prepration of new steel surface not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide complete all as specified . 39 m&l for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified. 40 s&f steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovatailed or welded as per is.1038:1983 ( amendment no.3 of may 2009 ) complete all as specified . 41 s&f steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay complete without glazing bars dovatailed or welded as per is.1038:1983 ( amendment no.3 of may 2009 ) complete all as specified . 42 m&l mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and / or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to fe 290 gde e 165 complete all as specified. n 43 s&f steel ventilator with top hung shutter incl. box type hinges with steel handle and steel peg stays complete with glazing bars welded as per is.1038:1983 ( amendment no.3 of may 2009 ) complete all as specified. 44 s&f 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified. 45 m&l galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average with of aperture 1.4mm and fixed withtinnwdtack, or galvanised wire staples complete all as specified. 46 s & f framed work as in door or gates of angle or other section with gusset plates rails, braces etc. complete, drilled for fixing of steel sheeting or other covering.door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering ) and hanging, also fastening and fixing complete all as specified. 47 m&l glazed and skeleton shutters 35 mm thick open rebated and prepared to receive glass, gauze, etc. ( without sash bars ) , edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in ssr part i, section 8, clause 8.20 ( a ) ; for doors supplied and fitted to chowkats complete all as specified and directed. 48 s&f plain framed, panelled shutter ( two panel ) factory made 35 mm thick of 2nd class hw rail and stylewith lock rail and panel of 9mm b.w.p. commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is: 1003 ( part i ) , kiln seasoned and chemically pressure treated, . complete all as specified and directed. 49 s&f aluminium anodised barrel tower bolt 150mm long complete all as specified and directed. 50 s&f aluminium alloy, anodised handle cast type of size 125mm complete all as specified and directed. 51 s&f aluminium alloy, anodised sliding door bolt of size 250mm with hasp and staple and fixing clips of sheet complete all as specified and directed. 52 m / l butt hinges medium weight, cold rolled mild steel, and fixed 100mm long complete all as specified and directed. 53 m&l cement concret ( 1:3:6 ) typec 2 using 40mm graded stone aggregate as in surface channel and drain complete all as specified and directed. 54 m&l extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, mitred / stopped ends etc. complete all as specified and directed. 55 s&f 15mm dia. unplasticised pvc pipes of pressure rating 10 kg / cm2 fixed complete to walls, ceillings or in floors etc. complete all as specified and directed. 56 s&f 20mm dia. unplasticised pvc pipes of pressure rating 10 kg / cm2 fixed complete to walls, ceillings or in floors etc. complete all as specified and directed. 57 s&f gunmetal , globe or gate valves, with iron wheel head, screwed both ends for 15 mm bore dia. iron pipe and fixed complete all as specified. n 58 s&f gunmetal , globe or gate valves, with iron wheel head, screwed both ends for 20 mm bore dia. iron pipe and fixed complete all as specified. n 59 s&f stop valves, fancy type, cast copper alloy, screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified n 60 s&f chromium plated bib taps, cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified . n n 61 s&f ball brass valves, high pressure, with polyethylene float and flynut complete , screwed for 20 mm bore dia. pipe or brass ferrule complete all as specified. n n 62 s&f rotational moulded poly ethylene multilayer water storage tanks ( cylinderical vertical with closed top ) 1000 litres capacity , hoisted and fixed in position complete all as specified. n n 63 m&l pvc ( swr ) pipes 110mm dia single socketed, in any length with rubber ring joints, laid in trenches or fixed to wall complete all as specified. 64 m&l pvc ( swr ) bend any radius 110mm dia complete all as specified. 65 m&l pvc ( swr ) tee any radius 110mm dia complete all as specified. 66 supply, installation, testing and commisioning of electric driven and integral electric heated, industrial washer cum extractor capacity 15 kg per cycle suitable for running on 3 phase 415 volts 50 hz, including all necessary accessories and components, mounted on self supporting rust proof frame with not less than 2 mm thick stainless steel body and all components of rust proof materials duly compatible for climatic conditions at ranchi. the machine shall be soft mounted and operatable to apply a minimum g force with following features complete all as specified ans as per manufacturers instructions: nmake : electrolux / stefab / fagor / unimac / fabcare / super shine / nagarjun as approved by the ge. n n n n 67 washer cylinder for washing, cleaning and extraction capacity 15 kg / cycle, complete electric driven and heated, front loading, heavy duty, heavy duty hot dip galvanized section frame, heavy duty rear gable and bearing support. both the inner and outer wash cylinders shall be constructed entirely using 2.0 mm thick stainless steel grade 304. 68 control : it shall have controlling panel with push button for selection of features. 69 detergent supply : the machines shall be available for use with powder or liquid detergents fed via integrated detergent dispensers . n 70 safety features: all machines shall be equipped with necessary safety interlock and warnings on the loading door. 71 auto weighing : automatic linen weighing system for automatic adjustment of water and soap consumptions as well as energy savings, according to the load inserted, measured automatically by the washer ) . 72 drive system : the machine shall have a motor powered by a vvvfdrive / vfd .there shall be no gearboxes, clutches or drive reducers. n 73 door opening: front loading not less than 400 mm ø 74 suppy, install test and commisoning of fully automatic industrial tumble dryer 15 kg linen capacity electric driven and electric heated, with integrated heating assembly, suitable for running on 3 phase 415 volts 50 hz, incl all necessary accessories and components, mounted on self supporting rust proof frame with complete stainless steel body n.less than 2.0 mm thick and all components of rust proof materials duly compatible for climatic conditions at ranchi with following features nmake : electrolux / stefab / fagor / unimac. fabcare / super shine / nagarjun as approved by the ge. n n 75 drying tumbler: capacity – 15 kg integral electric heated, electric vented, heavy duty, front loading, cool down feature, auto timed, auto / manually reversible dual motor drive, open pocket & front display. the dryer should be with temperature control system and the drum suspension should have sealed self lubricated bearings. 76 control : adjustable parameters such as temperature, programmes and cool down time and also the feature to control the residual moisture control in the linen. temperature and time controller shall be auto digital control with software for minimization of the cost and maximization of the up time of the equipment, which shall be able to capture features of a customised process and the drying programme shall be user friendly for editing / erasing preset programmes. drum–inner and outer drum should be made of stainless steel, 2 mm thick. 77 safety features : the tumble dryer should be equipped with overheating protection and a temperature sensor that turns off the heat if the air flow is clogged. n 78 door lock : the dryer should have a safety function or feature , which means the dryer should stops in case the door is opened during operation. transmission: the transmission should have pulley and belt or direct drive. there should be no gearboxes , clutches or gear reducers and the motor shall have vvvf / vf drive. n 79 door : made of die pressed stainless steel aisi not less than 2mm thick, toughened glass window , ss door latch / handle and interlock for safety. n 80 suction blower : heavy duty centrifugal suction blower and dynamically balanced. lint screen self cleaning lint screen, facility of cleaning should be through front 81 suppy, installation, testing and commisoning vaccum finising table utility shape for general purpose, with integral vacuum fan and steam electric iron and integral boiler, ac, 3 phase, 380 415v with rectangular vaccum ironing table having dimensions 1300mm ( width ) x 800mm ( depth ) x920mm ( height ) complete all as specified and as directed. nmake : fabcare / stefab / super shine / nagarjun as approved by the ge. 82 supply installing , testing and commisioning stream cum electric press complete all as specified and as directed. nmake : electrolux / stefab / fagor / unimac. fabcare / super shine / nagarjun as approved by the ge. 83 supply installing , testing and commisioning electrical stream boiler operate at ac, 3 phase, 380 415v, 50 hz suitable for operating mechanical laundry consisting as per item no 66 to 69 complete all as specified and as directed. nmake : thermax or other equivalent make as approved by the ge. 84 m&l for cpvc pipe, isi marked of required size and of approved make as per requirement of plant with required fittings complete for water lines for connection from source to individual machines like washer extractor, drier, flat bed press, ironing table with standard size pipe lines / cables as per manufacturers recommendations for efficient functioning of the equipments complete as directed. n 85 supply and fix mcb db, tpn 8 way ip 43 protection , double door , concealed on wall complete all as specified and as directed. nmake : indo asian / legrand / l & t / standard / havells / hpl as approved 86 s&f distribution board spn 230 volt, 4 way, double door type, concealed on wall suitable for mcb dp incomer and sp outgoing complete all as specified and as directed. nmake indo asian / legrand / l &t / standard / hpl as approved. 87 supply and fix mcb of follwing rating with necessary lugs for incomming and outgong connections fixed on db / enclosure / panel boards complete all as specified and directed. nmake : indo asian / legrand / l & t / standard / havells / hpl as approved. 88 mcb sp 6 to 32 amp 89 mcb dp 6 to 32 amp. 90 mcb 4 pole 6 to 32 amp. 91 s & f sheet metal tp and neutral enclosure with one mcb tp 6 to 32 amp and metal clad plug and socket ( rating of mcb suitable as per machine / load capacity ) amp and concelaled on wall complete all as specified n make : indo asian / legrand / l & t / standard / havells / hpl as approved. 92 s & f sheet metal dp enclosure with one mcb dp 16 amp and metal clad plug and socket ( rating of mcb suitable as per machine / load capacity ) concelaled on wall complete all as specified n make : indo asian / legrand / l & t / standard / havells / hpl as approved 93 m&l for sub main wiring with 4.0 run single core 4.0 sqmm pvc unsheathed copper multistranded conductor, frls , drawing into and including pvc conduit concealed medium grade of size not less than 20 mm dia with all fittings and fixtures like l bow, saddles etc of white / ivory colour pvc conduit including multi stranded copper earth conductor 4.0 sq mm , frls two run as earth continuty conductor complete all as specified and as directed. nnote : 4 run of cable and two run of earth conductor cable and conduit shall be measured as one length. 94 m / l for sub main wiring with 2.0 run single core 4.0 sqmm pvc unsheathed copper multistranded conductor, frls , drawing into and including pvc conduit concealed medium grade of size not less than 20 mm dia with all fittings and fixtures like l bow, saddles etc of white / ivory colour pvc conduit including multi stranded copper earth conductor 4.0 sq mm , frls one run as earth continuty conductor complete all as specified nnote : 2 run of cable and one run of earth conductor cable and conduit shall be measured as one length. 95 supply and lay cable xlpe insulated screened pvc bedded, galvanized steel strip or wire armored, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 16 sqmm 4 core.complete all as specified n ( make : polycab / havells / plaza as approved 96 excavation in trenches not exceeding 1.5 mtr deep and not exceeding 1.5 mtr width and getting out in hard / dense soil complete all as specified and as directed 97 returning filling in including spreading, leveling, watering and well ramming in layer not exceeding 25 cm thick complete all as specified and as directed 98 removal of surface soil to a distance n.exc 50 m and deposited where directed at a level n. exc 1.5 m above the starting point complete all as specified and as directed 99 m & l river sand for cushioning for cable protection in trenches 8 cm before laying cable and 15 cm deep after laying of cable complete all as specified and as directed n ( note: punned thickness shall only be measured for payment ) 100 m&l laying well burnt old size bricks, sub class b bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified. 101 m&l for point wiring complete as specified with 1100 v grade with 1.5 sq mm single core pvc insulated unsheathed frls cable, copper conductor multistranded passing through including concealed pvc conduit not less than 20 mm dia with concealed modular metal box sutable for switches , sockets , etc and with gi / ms box, 2.0 mm thickness concealed with necessary top plate of suitable size as required at site with pvc insulated frls unsheathed stranded copper conductor of size 1.5 sq mm as earth wire connected to common earth dully as specified for folowing all as specified and as directed . 102 one light point controlled by one switch 103 one exhaust fan point controlled by one switch 104 5 amp switch socket on the same board. 105 5 amp switch socket on independent board. 106 all as per item no 85 above but size of cable 2.5 sq mm for 15 amps switch socket with earth wire of 2.5 sq mm and ditto 107 s&f switch 5 amps piano type 230 volts one way complete all as specified and as directed 108 s&f switch socket combination 5 amps flush type 230 volts one way acomplete all as specified and as directed n 109 s&f switch socket combination 5 / 15 amps flush type 230 volts one way complete all as specified and as directed 110 s&f ceiling rose surface backlite 65 x 50 mm two to three terminal suitable for 230 volts ac supply complete all as specified and as directed 111 s&f exhaust fan fan 230 volt 50 hz single phase ac supply , 300 mm sweep with louver complete with metal body powder coated with protective steel bird gaurd on wall including provision of 3 core 1.0 sq mm flexible cable from ceiling rose to exhaust fan including writing mes number on exhaust fan motor complete all as specified and as directed nmake: havells / almonard / bajaj. 112 supply & fix led tube light along with base frame , 18 w fixed on wall / ceiling complete all as specified and as directed by engineer in charge . nmake: havells / wipro / bajaj / philips / hpl / luker . 113 m & l earthing complete with galvanized steel earth plate electrode 600x600x6.0mm thick buried directly in ground ( earth pit not less than 2.25 meters deep below ground level ) with top edge of the plate not less that 1.5 meters below normal ground level connected to galvanized iron strip 25 x 4 mm as earthing by means of bolts nuts and washers of galvanized iron including excavation and earth work and disposal of surplus soil including 40 mm gi tubing light grade and necessary fittings for protection of gi strip including layong of charcoal , dust and common slat , pcc 1:2: 4 type b 1 using 320 mm graded aggregate with earth pit with 40 x 40 x 6.0 mm ms angle iron frame rcc cover 40 mm thick ( 1:2: 4 ) type c1 using 20 mm graded stone aggregate reinforced with 8 mm dia round bar @ 75 mm c / c both way with ms handle 20 mm dia plastering 15 mm thick cm ( 1: 6 ) internally and up to 150 mm below ground level externally . pgi funel with wire mesh 20 mm dia gi pipe for watering complete all as shown on electrical plate no : 03 of ssr part i 2009 and connected to earth test point including testing complete all as specified and as directed...

Military Engineer Services - Jharkhand

23972362 repair maintenance of wooden windows and door steel window aluminium window and ventilator wire mesh and glass pane including misc items for joinery under age br ii area at dipatoli mil stn...

Jawahar Vidya Mandir - Jharkhand

23933242 tender for dismantling of old steel window, supply and fixing by two track upvc sliding window, 225 number in jvm premises....

Military Engineer Services - Jharkhand

23872686 door, steel window, aluminium window and ventilator, wire mesh and glass pane including misc items for joinery under age b/r ii area at dipatoli mil stn...

Military Engineer Services - Jharkhand

23384798 providing of room for laundry including equipments under ge dipatoli 1 excavation in trenches n exc 1.5 m wide n exc 1.5 m deep and getting out in soft / loose soil for foundation etc or for shaft, wells, manholes etc n exc 10 sqm on plan and not exc 1.5 m in depth and getting out. complete all as specified and directed. 2 removing excavated material to a distance n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed. 3 returning, filling in including spreading, leveling, watering and well ramming in layers n.exc.25 cm complete all as specified and directed. 4 m&l cement concret ( 1:4:8 ) type d 2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed. 5 m&l reinforced cement concrete m 25 ( design mix ) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified. n 6 m&l reinforced cement concrete m 25 ( design mix ) as in columns, pillars, piers, posts and struts complete all as specified and directed. 7 m&l reinforced cement concrete in cement concrete m 25 ( design mix ) as in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified. n 8 m&l reinforced cement concrete m 25 ( design mix ) as in slabs supported on walls, beams and columns , in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified. 9 m&l precast cement concrete type b 1 ( 1:2:4 ) using 20mm graded stone aggregates, as in man hole cover slabs, shelves, and similar work set in cm ( 1:4 ) .complete all as specified and directed. 10 use and waste of formwork to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions surfaces finished fair as per clause 4.11.16.2 ( a ) of ssr part i complete all as specified. n 11 use and waste formwork to flat sides and soffits of floor or roof beams, beam haunchings, girders, bresumers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc. surfaces finished fair complete all as specified. n 12 use and waste of formwork to fair surfaces of sides of concrete foundations, footings, bases of columns , raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or to batter surfaces finished fair in forms complete all as specified. n n 13 use and waste of form work to flat soffits of suspended slabs, floor slabs, landings and similar work; not exceeding 200 mm thick ( horizontal or sloping ) surfaces finished fair in forms complete all as specified. n 14 use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs sides of rcc / pcc bands in walls , horizontal or sloping and similar work exc 10cm but n exc 20 cm wide, surfaces finished fair in forms complete all as specified. 15 m&l mild steel deformed or twisted bars ( tmt ) 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.90 mm dia. or higher complete all as specified. n 16 m&l mild steel deformed or twisted bars ( tmt ) 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.90 mm dia. or higher complete all as specified. n 17 m&l mild steel bars ( tmt deformed / twisted ) 8mm dia. and over up to and including 10 mm dia. in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.90 mm dia. or securing with clips complete all as specified. 18 m &l for brickwork with sub class b old size bricks, straright or corved on plan exc 6m mean radius built in cement mortar ( 1:6 ) complete all as specified and as directed. 19 m&l brickwork with subclass b old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed. 20 supply only liquid water proofing compound complete all as specified and directed. 21 m&l roof treatment for non approachable roof complete all as specified and directed comprising of followings: ( i ) rendering 10mm thick in cement mortor ( 1:3 ) mixed with liquid water proofing compound finished the surface fair and even. ( ii ) applying evenly a coat of bitumen primer @ 0.30 kg / sqm. ( iii ) applying app modified polymeric membrane over the bitumen coat surface , weight not less than 3.20 3.50 kg / sqm and over lap 100mm and sealed by torch application as per manufacture insteructions. ( iv ) applying a coat of aluminium paint @ 200 gm / sqm in two coats over polymeric membrene. 22 surface dressing in soft / loose soil n exc 15 cm deep trimming of natural ground ( removing vegetation / shurbs / brushwood. undergrowth and carring away rubbish to a distance of not exc 50 metre complete all as specified and directed. 23 m&l sand filling under floors or in foundation including watering and consolidation ( with lead of 50 m. for sand ) complete all as specified and directed. 24 m&l moorum / red bajri filling in floors or pavings, laid in floors n.exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed. 25 m&l for 100mm thickpcc ( 1:4:8 ) type d 2 using 40mm graded stone aggregate as in sub base complete all as specified and directed. 26 m&l for 75 mm thick pcc 1:3:6 type c 2 using 40mm graded stone aggregates, as in plinth protection and path etc finished cement concrete surface even and smooth without using extra cement all as specified. 27 m&l machine cut kota stone slab flooring 18 20 mm thick set over and including 15mm thick screed base in cm ( 1:6 ) , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beewax polishing complete all as specified and directed. 28 all as per item no 27 but here in before as in skirting set over and including 10mm thick cement plaster in cm 1:6 complete all as specified and directed.. 29 m&l white marble stone slab flooring 18 20 mm thick set over and including 15mm thick cement sceed base in cm 1:6 laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beewax polishing complete as a boarder in the kota stone floorig all as specified and directed. 30 m&l machine cut cuddapa stone slab 20 25 mm thick, laid over 15mm thick cm ( 1:6 ) cement screed base, laid and jointed with grey ement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed. 31 m&l rendering 15 mm thick on fair faces of brick work or concrete surfaces , in cement and sand mortar 1:6 , top surfaces finished even and smooth without using extra cement complete all as specified n n 32 m&l rendering 15 mm thick on fair faces of brick work or concrete surfaces , in cement and sand mortar 1:4, mixed with using liquid water proofing compound complete all as specified ) , top surfaces finished even and smooth without using extra cement complete all as specified and directed. nnote : wpc measured and paid separately n 33 rendering in cement mortar i:3 on fair face of cement concrete on ceiling 10mm thk finished surface even and smooth without using extra cement complete all as specified n 34 m&l applying three coat of white wash on newly plastered surfaces of walls including washing floors, cleaning glass, joinery, electrical fittings, wiring etc. , of drops and splashes complete all as specified . 35 m&l two coats distempering with cement base paint , white or tinted over a coat of cement base primer on new surfaces of walls including washing floors, cleaning glass, joinery, electrical fittings, wiring etc. , of drops and splashes complete all as specified . n n 36 m&l preparation of new plastered or unplastered surafces of ceilings and applying three coats of white wash including washing floors, cleaning glass, joinery, electrical fittings, wiring etc. , of drops and splashes complete all as specified . n n 37 m&l for cement concrete 1:2:4 type b 1 ( using 20mm graded stone aggregate ) as in bed block for hold fast & filling in pressed steel door frame complete all as specified . 38 m&l for prepration of new steel surface not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide complete all as specified . 39 m&l for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified. 40 s&f steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovatailed or welded as per is.1038:1983 ( amendment no.3 of may 2009 ) complete all as specified . 41 s&f steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay complete without glazing bars dovatailed or welded as per is.1038:1983 ( amendment no.3 of may 2009 ) complete all as specified . 42 m&l mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and / or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to fe 290 gde e 165 complete all as specified. n 43 s&f steel ventilator with top hung shutter incl. box type hinges with steel handle and steel peg stays complete with glazing bars welded as per is.1038:1983 ( amendment no.3 of may 2009 ) complete all as specified. 44 s&f 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified. 45 m&l galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average with of aperture 1.4mm and fixed withtinnwdtack, or galvanised wire staples complete all as specified. 46 s & f framed work as in door or gates of angle or other section with gusset plates rails, braces etc. complete, drilled for fixing of steel sheeting or other covering.door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering ) and hanging, also fastening and fixing complete all as specified. 47 m&l glazed and skeleton shutters 35 mm thick open rebated and prepared to receive glass, gauze, etc. ( without sash bars ) , edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in ssr part i, section 8, clause 8.20 ( a ) ; for doors supplied and fitted to chowkats complete all as specified and directed. 48 s&f plain framed, panelled shutter ( two panel ) factory made 35 mm thick of 2nd class hw rail and stylewith lock rail and panel of 9mm b.w.p. commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is: 1003 ( part i ) , kiln seasoned and chemically pressure treated, . complete all as specified and directed. 49 s&f aluminium anodised barrel tower bolt 150mm long complete all as specified and directed. 50 s&f aluminium alloy, anodised handle cast type of size 125mm complete all as specified and directed. 51 s&f aluminium alloy, anodised sliding door bolt of size 250mm with hasp and staple and fixing clips of sheet complete all as specified and directed. 52 m / l butt hinges medium weight, cold rolled mild steel, and fixed 100mm long complete all as specified and directed. 53 m&l cement concret ( 1:3:6 ) typec 2 using 40mm graded stone aggregate as in surface channel and drain complete all as specified and directed. 54 m&l extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, mitred / stopped ends etc. complete all as specified and directed. 55 s&f 15mm dia. unplasticised pvc pipes of pressure rating 10 kg / cm2 fixed complete to walls, ceillings or in floors etc. complete all as specified and directed. 56 s&f 20mm dia. unplasticised pvc pipes of pressure rating 10 kg / cm2 fixed complete to walls, ceillings or in floors etc. complete all as specified and directed. 57 s&f gunmetal , globe or gate valves, with iron wheel head, screwed both ends for 15 mm bore dia. iron pipe and fixed complete all as specified. n 58 s&f gunmetal , globe or gate valves, with iron wheel head, screwed both ends for 20 mm bore dia. iron pipe and fixed complete all as specified. n 59 s&f stop valves, fancy type, cast copper alloy, screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified n 60 s&f chromium plated bib taps, cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified . n n 61 s&f ball brass valves, high pressure, with polyethylene float and flynut complete , screwed for 20 mm bore dia. pipe or brass ferrule complete all as specified. n n 62 s&f rotational moulded poly ethylene multilayer water storage tanks ( cylinderical vertical with closed top ) 1000 litres capacity , hoisted and fixed in position complete all as specified. n n 63 m&l pvc ( swr ) pipes 110mm dia single socketed, in any length with rubber ring joints, laid in trenches or fixed to wall complete all as specified. 64 m&l pvc ( swr ) bend any radius 110mm dia complete all as specified. 65 m&l pvc ( swr ) tee any radius 110mm dia complete all as specified. 66 supply, installation, testing and commisioning of fully automatic, electric driven and integral electric heated, industrial washer cum extractor capacity 15 kg per cycle suitable for running on 3 phase 415 volts 50 hz, including all necessary accessories and components, mounted on self supporting rust proof frame with not less than 2 mm thick stainless steel body and all components of rust proof materials duly compatible for climatic conditions at ranchi including controlled through programmable logic control ( plc ) auto time auto reverse, auto stop, auto temp contro, l auto level control, pneumaticlly operated valves for auto water inlet, auto steam inlet, auto drain. the machine shall be soft mounted and operatable to apply a minimum g force with following features complete all as specified ans as followings: nmake : electrolux / stefab / fagor / unimac / fabcare / super shine / nagarjun as approved by the ge. n n n n 67 washer cylinder for washing, cleaning and extraction capacity 15 kg / cycle, complete electric driven and heated, front loading, heavy duty, heavy duty hot dip galvanized section frame, heavy duty rear gable and bearing support. both the inner and outer wash cylinders shall be constructed entirely using 2.0 mm thick stainless steel grade 304. 66.1 68 control : the machine shall be controlled with a fully programmable micro computer and should be able to capture features of a customised process. it shall have an lcd touch interface with customised and user operatable general wash settings. it shall be user friendly for editing / erasing preset programmes. n 66.2 69 detergent supply : the machines shall be available for use with powder or liquid detergents automatically fed via integrated detergent dispensers with minimum 5 compartments without user intervention. n 66.3 70 safety features: all machines shall be equipped with necessary safety interlock and warnings on the loading door. 66.4 71 auto weighing : automatic linen weighing system for automatic adjustment of water and soap consumptions as well as energy savings, according to the load inserted, measured automatically by the washer ) . 66.5 72 drive system : the machine shall have a motor powered by a vvvfdrive / vfd .there shall be no gearboxes, clutches or drive reducers. n 66.6 73 door opening: front loading not less than 500 mm ø 66.7 74 suppy, install test and commisoning of fully automatic industrial tumble dryer 15 kg linen capacity electric driven and electric heated, with integrated heating assembly, suitable for running on 3 phase 415 volts 50 hz, incl all necessary accessories and components, mounted on self supporting rust proof frame with complete stainless steel body n.less than 2.0 mm thick and all components of rust proof materials duly compatible for climatic conditions at ranchi with following features nmake : electrolux / stefab / fagor / unimac. fabcare / super shine / nagarjun as approved by the ge. n n 75 drying tumbler: capacity – 15 kg integral electric heated, electric vented, heavy duty, front loading, cool down feature, auto timed, auto / manually reversible dual motor drive, open pocket & front display. the dryer should be with temperature control system and the drum suspension should have sealed self lubricated bearings. 67.1 76 control : microcomputer with adjustable parameters such as temperature, programmes and cool down time. and also the feature to control the residual moisture control in the linen. temperature and time controller shall be auto digital control with software for minimization of the cost and maximization of the up time of the equipment. the process shall be through a fully programmabl with touch interface, which shallbe able to capture features of a customised process and the drying programme shall be user friendly for editing / erasing preset programmes. drum–inner and outer drum should be made of stainless steel, 2 mm thick. 67.2 77 safety features : the tumble dryer should be equipped with overheating protection and a temperature sensor that turns off the heat if the airflow is clogged. n 67.3 78 door lock : the dryer should have a safety function or feature , which means the dryer should stops in case the door is opened during operation. transmission: the transmission should have pulley and belt or direct drive. there should be no gearboxes , clutches or gear reducers and the motor shall have vvvf / vf drive. n 67.4 79 door : made of die pressed stainless steel aisi not less than 2mm thick, toughened glass window , ss door latch / handle and interlock for safety. n 67.5 80 suction blower : heavy duty centrifugal suction blower and dynamically balanced. lint screen self cleaning lint screen, facility of cleaning should be through front 67.6 81 suppy, installation, testing and commisoning vaccum finising table utility shape for general purpose, with integral vacuum fan and steam electric iron and integral boiler, ac, 3 phase, 380 415v with rectangular vaccum ironing table having dimensions 130mm ( width ) x 80mm ( depth ) x920mm ( height ) complete all as specified and as directed. nmake : fabcare / stefab / super shine / nagarjun as approved by the ge. 82 supply installing , testing and commisioning stream cum electric press complete all as specified and as directed. nmake : electrolux / stefab / fagor / unimac. fabcare / super shine / nagarjun as approved by the ge. 83 supply installing , testing and commisioning electrical stream boiler operate at ac, 3 phase, 380 415v, 50 hz suitable for operating mechanical laundry consisting as per item no 66 to 69 complete all as specified and as directed. nmake : thermax or other equivalent make as approved by the ge. 84 m&l for cpvc pipe, isi marked of required size and of approved make as per requirement of plant with required fittings complete for water lines for connection from source to individual machines like washer extractor, drier, flat bed press, ironing table with standard size pipe lines / cables as per manufacturers recommendations for efficient functioning of the equipments complete as directed. n 85 supply and fix mcb db, tpn 8 way ip 43 protection , double door , concealed on wall complete all as specified and as directed. nmake : indo asian / legrand / l & t / standard / havells / hpl as approved 86 s&f distribution board spn 230 volt, 4 way, double door type, concealed on wall suitable for mcb dp incomer and sp outgoing complete all as specified and as directed. nmake indo asian / legrand / l &t / standard / hpl as approved. 87 supply and fix mcb of follwing rating with necessary lugs for incomming and outgong connections fixed on db / enclosure / panel boards complete all as specified and directed. nmake : indo asian / legrand / l & t / standard / havells / hpl as approved. 74 88 mcb sp 6 to 32 amp 89 mcb dp 6 to 32 amp. 90 mcb 4 pole 6 to 32 amp. 91 s & f sheet metal tp and neutral enclosure with one mcb tp 6 to 32 amp and metal clad plug and socket ( rating of mcb suitable as per machine / load capacity ) amp and concelaled on wall complete all as specified n make : indo asian / legrand / l & t / standard / havells / hpl as approved. 92 s & f sheet metal dp enclosure with one mcb dp 16 amp and metal clad plug and socket ( rating of mcb suitable as per machine / load capacity ) concelaled on wall complete all as specified n make : indo asian / legrand / l & t / standard / havells / hpl as approved 93 m&l for new sub main wiring with 4.0 run single core 4.0 sqmm pvc unsheathed copper multistranded conductor, frls , drawing into and including pvc conduit concealed medium grade of size not less than 20 mm dia with all fittings and fixtures like l bow, saddles etc of white / ivory colour pvc conduit including multi stranded copper earth conductor 4.0 sq mm , frls two run as earth continuty conductor complete all as specified and as directed. nnote : 4 run of cable and two run of earth conductor cable and conduit shall be measured as one length. 94 m / l for new sub main wiring with 2.0 run single core 4.0 sqmm pvc unsheathed copper multistranded conductor, frls , drawing into and including pvc conduit concealed medium grade of size not less than 20 mm dia with all fittings and fixtures like l bow, saddles etc of white / ivory colour pvc conduit including multi stranded copper earth conductor 4.0 sq mm , frls one run as earth continuty conductor complete all as specified nnote : 2 run of cable and one run of earth conductor cable and conduit shall be measured as one length. 95 supply and lay cable xlpe insulated screened pvc bedded, galvanized steel strip or wire armored, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 16.0 sq mm 4 core.complete all as specified n ( make : polycab / havells / plaza as approved 96 excavation in trenches not exceeding 1.5 mtr deep and not exceeding 1.5 mtr width as in hard dense soil soil complete all as specified and as directed 97 returning filling incl leveling watering and well ramming in layer not exceeding 25 cm thick complete all as specified and as directed 98 removal of surface soil to a distance n.exc 50 m and deposited where directed at a level n. exc 1.5 m above the starting point complete all as specified and as directed 99 m & l river sand for cushioning for cable protection in trenches 8 cm before laying cable and 15 cm deep after laying of cable complete all as specified and as directed n ( note: punned thickness shall be taken for measurement ) 100 m&l laying well burnt old size bricks, sub class b bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified. 101 m&l for point wiring complete as specified with 1100 v grade with 1.5 sq mm single core pvc insulated unsheathed frls cable, copper conductor multistranded passing through including concealed pvc conduit not less than 20 mm dia with concealed modular metal box sutable for switches , sockets , etc and with gi / ms box, 2.0 mm thickness concealed with necessary top plate of suitable size as required at site with pvc insulated frls unsheathed stranded copper conductor of size 1.5 sq mm as earth wire connected to common earth dully as specified for folowing all as specified and as directed . 85 102 one light point controlled by one switch 103 one exhaust fan point controlled by one switch 104 5 amp switch socket on the same board. 105 5 amp switch socket on independent board. 106 all as per item no 85 above but size of cable 2.5 sq mm for 15 amps switch socket with earth wire of 2.5 sq mm and ditto 107 s&f switch 5 amps piano type 230 volts one way complete all as specified and as directed 108 s&f switch socket combination 5 amps flush type 230 volts one way acomplete all as specified and as directed n 109 s&f switch socket combination 5 / 15 amps flush type 230 volts one way complete all as specified and as directed 110 s&f ceiling rose surface backlite 65 x 50 mm two to three terminal suitable for 230 volts ac supply complete all as specified and as directed 111 s&f exhaust fan fan 230 volt 50 hz single phase ac supply , 300 mm sweep with louver complete with metal body powder coated with protective steel bird gaurd on wall including provision of 3 core 1.0 sq mm flexible cable from ceiling rose to exhaust fan including writing mes number on exhaust fan motor complete all as specified and as directed nmake: havells / almonard / bajaj. 112 supply & fix led tube light along with base frame , 18 w fixed on wall / ceiling complete all as specified and as directed by engineer in charge . nmake: havells / wipro / bajaj / philips / hpl / luker . 113 m & l earthing complete with galvanized steel earth plate electrode 600x600x6.0mm thick buried directly in ground ( earth pit not less than 2.25 meters deep below ground level ) with top edge of the plate not less that 1.5 meters below normal ground level connected to galvanized iron strip 25 x 4 mm as earthing by means of bolts nuts and washers of galvanized iron including excavation and earth work and disposal of surplus soil including 40 mm gi tubing light grade and necessary fittings for protection of gi strip including layong of charcoal , dust and common slat , pcc 1:2: 4 type b 1 using 320 mm graded aggregate with earth pit with 40 x 40 x 6.0 mm ms angle iron frame rcc cover 40 mm thick ( 1:2: 4 ) type c1 using 20 mm graded stone aggregate reinforced with 8 mm dia round bar @ 75 mm c / c both way with ms handle 20 mm dia plastering 15 mm thick cm ( 1: 6 ) internally and up to 150 mm below ground level externally . pgi funel with wire mesh 20 mm dia gi pipe for watering complete all as shown on electrical plate no : 03 of ssr part i 2009 and connected to earth test point including testing complete all as specified and as directed...

Military Engineer Services - Jharkhand

22037104 repairs replacement of joinery and connected items in prc temple lane and mes md area at ramgarh cantt 1 taking down shutter of any descipriton n exc. 1.00 sqm each and refixing in same opening complete all as spd and directed by engr in charge . 2 , ditto but exc but n.exc 2.00 sqm each 3 , ditto exc 2.00 sqm but exc. 4.00sqm each 4 resecuring or easing and adjusting of old shutter without taking out from the frame of any description of area exceeding 1.00 sqm but not exc.2.00 sqm each complete all as directed by engineer in charge 5 , ditto but exc but exc. 2.00 sqm each 6 taking down chawkhat with shutter ( without taking of shutter from the frame ) of any descipriton n.exc 1.5 sqm each complete all as spd and directed by engr in charge . 7 ditto but exc 1.5 sqm but not exc 4 sqm 8 taking down chawkhat with shutter ( without taking of shutter from the frame ) of aluminium descipriton n.exc 1.5 sqm each complete all as specified and directed by engr in charge . 9 ditto as item no:8 but exc 1.5 sqm but not exc 4 sqm 10 taking down steel window / ventilater n exc 1.5 sqm each complete all as spd and directed by engr in charge . 11 hacking out old brocken glass ( any thickness , size quality or desrp ) from old wooden frames / metal frame or stone , concrete or brick surrounds, glazing with putty or fixed with beads. 12 dismantling particle board boarding of any description fixed with nails as in kitchen cupboard and pelmet box etc. 13 s&f pressed steel frames of size 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate, etc completeas specified and directed. 14 s&f pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate, etc completeas specified and directed. 15 s&f 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side. all as per spd and directed. 16 m&l chowkhat 2nd class hard wood and frmaes wrought , framed rebated on the solid rounded or chamfered , put together with gluepinned at joints complete all as spd and directed by engr in charge .supplied and fixed 17 s&f solid pvc door frame of size 50mm x 47mm made out f 5mm plain colour pvc sheet reinforced with ms square tubes suppling & fixing in opening as per specification & drawing complete all as spd and directed by engr in charge . 18 factory made solid panel pvc door shutter 30mm thick ( style ) consisting of frame made out of ms tube for top &bottom rails. ms framed shall be covered with heat molded plain colour pvc ‘c’ channel having a pvc sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour pvc sheet for top rail, lock rail &bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour pvc sheet to be fitted in the ms framed welded / sealed to stiles & rails with suitable pvc sheet beading & joined together with solvent cement complete 19 factory made solid panel pvc door shutter 30mm thick ( style ) made internal pvc flush door / cup board shutterwood free consisting of frame made out of ms tubes 19 gauge thickness and size of 40 mm x 20 mm for style for top lock & bottom rails. ms frame shall haave a coat of metaln primer of approved make and manufacture. the inside panel shall consist of 20 mm th multichamber hollow pvc section of 1mm th wall thickness bonded using solvent cement / cynoacrylate adhesive ( +5mm th plain / prelam upvc ( rigid ) sheet of denisity ) 600 kg / cum manufactured by an iso 9000 certified company on both side of the inside panel all of four edges of the panel yo be sealed with leaping of 10 mm thick and 20 mm wide upvc rigid sheet of 5 mm thickness using pvc solvent cement adhesive. door of edges leaping to be painted with pvc inkof matching colour of plain / prelam moulded upvc rigid sheet of door 20 mm thick ( 5mmx4nos ) thick upvc to be given for lock provision at lock height. door to be fixed with frame with three nos ss butt hinges of size 100x25x2mm and 50 mm long steel screw drill suitable to pass through both the walls of the ms steel other hardware should be fixed 25x8mm size steel screw etc.complete all as specified. 20 s&f 30 mm thick 2nd class hard wood glazed & skelton shutters, open repeated & prepared to received glass gauze etc. with sash bars, edges of framing plain for securing glass etc. ( without sash bars ) , edges of framing plain , fitted to chawkhats complete all as spd and directed by engr in charge . 21 ditto as above item no 20 but 30mm thick as in window shuters without sash bars 22 s&f for steel window with side hung shutter incl projecting type hinge with steel handle, and steel peg stay complete with glazing bars dovetailed or welded, 3mm complete all as specified and directed. 23 s&f for steel window with side hung shutter incl projecting type hinge with steel handle, and steel peg stay complete without glazing bars dovetailed or welded, 3mm complete all as specified and directed. 24 s&f steel ventilator with top hung shutter including hinges, steel peg stay complete 25 s&f framed work such as grill granting etc with end of bars shouldred and / or revated or forged into spikes framed guard bars barred iron dors and similar works conferming to fe 410 0 or fe 310 0 including all necessary welding complete all as spd and directed by engr in charge . 26 s&f angle iron as in door frame & framed work as in doors or gates of angle and similar works conferming to fe 410 w. including all necessary welding complete all as spd and directed by engr in charge . 27 s&f 1mm thick mild steel plain black sheet in wall cladding steel gates and similar work, cut to size holes punched including round haded screws, clout nails to revates and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams including bending or turning up, mitred angles etc as required complete all as spd and directed by engr in charge . 28 m&l pcc 1:3:6 bed block for fixing of hold fasts etc. 29 s&fmild steel flat iron work as in hold fast including all nesessary cutting etc complete all as specified and directed. 30 m&l 18 / 19mm thick prelaminated particle board exterior grade prelaminated one side with decorative choice lamination other side balancing white lamination fixed with screw to timber frame work complete all as spd and directed by engr in charge . 31 s&f stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed to wooden fillet & beads complete all as spd and directed by engr in charge . 32 s&f stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed to wooden fillet & beads fixed in repair complete all as spd and directed by engr in charge . 33 m & l for 3mm thick plain sheet glass ordinary quality & glazing with oil putty n.exc 0.50 sqm in each pane complete all as spd and directed by engr in charge . 34 ditto as above item no 33 but figured glass, pinheaded type 35 mild steel helical door spring of size 150mm including roller and roller plate fixing to iron frame by welding all as directed. 36 s &f mild steel sliding door bolts 250mm long , plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and two on staple plate and fixed complete all as spd and directed by engr in charge . 37 s&f aluminium alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet, cast extruded section & fixing bolts& sliding bolts of extruded section on 250 mm long. 38 s & f 100mm butt hinges medium weight medium cold rolled mild steel complete all as spd and directed by engr in charge . 39 s & f 100mm butt hinges extruded aluminium alloy with galvanised ms hinge pin, anodised and fixed type b 21 comlpete all as spd and directed by engr in charge . 40 ditto as above item no but size of 75mm type c 21 41 s&f mild steel barrel tower bolts 150mm , stove enamelled black with bright bolt and fixed complete all as spd and directed by engr in charge . 42 supply and fix in repairs 200mm long aluminium anodised barrel tower bolt of extruded section and fixed in repairs complete all as specified and directed. 43 supply and fix 150mm long aluminium anodised barrel tower bolt of extruded section and fixed in repairs complete all as specified and directed. 44 fixing only aluminium tower bolt 150 mm long stove enamelled black with bright bolt, fixed in repair complete all as spd and directed by engr in charge 45 s&f mild steel pressed handles oval type 150mm long , stove enamelled black complete all as spd and directed by engr in charge . 46 ditto as above item no but size of 100mm 47 refixing mild steel pressed handles oval type 125mm long , stove enamelled black 48 supply and fix aluminium handle cast type, anodised, 150 mm size in repairs complete all as specified and directed 49 s&f 100mm aluminium handle cast type anodised fixed with screw complete all as spd and directed by engr in charge . 50 s&f ball catcher with 8mm dia steel ball and brass body and striking plate including letting in and fixed 51 s&f iind class hard wood small items such as brackets n.exc 200mm , latch and hinge blocks, shapped door and window stops and the like inclduing all nex labours articles nexc 200 cucm each complete all as spd and directed by engr in charge . 52 running welding in repairs thickness of metal to be welded exc 6mm but n exc 9mm 53 demolition of brick work or stone / boulder masonry , but built in cement mortar or cement lime mortar complete all as spd and directed by engr in charge . 54 m&l brick work with sub class b old size bricks straight on curved on plan exc.6m mean radius built in cement mortar 1:6 complete all as spd and directed by engr in charge . 55 brick work with sub class b bricks straight or curved on plan to any radiusin half brick thick wall built in cement mortar 1:4, complete all as specified and directed 56 m&l rendering 15mm thick on fair faces of brick work or concrete surfaces in cm 1:6 on wall complete 57 m&l painting on new steel surfaces of any description not other wise described over 10cm width or girth applying two coat synthetic enamel paint over one coat of red oxide primer including preparation of surfaces complete all as spd and directed by engr in charge . 58 m&l painting on new wooden based surfaces of any description not other wise described over 10cm width or girth applying two coat synthetic enamel paint over one coat of pink primer including preparation of surfaces complete all as spd and directed by engr in charge . 59 m&l applying three coat of white washing including preparing of new plastered wall surfaces. 60 preparation of new plastered surfaces of walls using sand paper and applying two coats of cement base paint complete all as specified and as directed. 61 preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of priming paint complete all as specified and directed 62 s&f piano hinges mild steel bright finish 30mm flap all as spd and directed. 63 s&f in repair ms ordinary rat tail rod pattern springs 300 mm including roller and roller plate on wooden / steel chowkhat incl welding , riveting etc complete all as specified and directed by engineer in charge. 64 s& f in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty for aluminium door complete all as specified and directed by engineer in charge. 65 s&f 40mm dia, cupboard nobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed by engineer in charge. 66 s&f anodised aluminium frame for doors, windows, ventilators for two / three track channel including joining cleat, rubber packing etc, complete all as specified by engr in charge. 67 anodised aluminium door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified 68 s& f anodised aluminium window shutters, side hung type without sash bar, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazzing clips, roller, rubber packing, anodised aluminium snap beading, screws anodised aluminium fittings such as hinges type b 21 100mm long ( 2 no ) suitable handle ( 1 no ) etc.complete all as specified by engr in charge. 69 s&f for 12 mm thick pre laminated particle board, exterior grade, pre laminated both sides with decorative choice lamination fixed in aluminum shutter / partition complete all as specified and directed. 70 m & l for 5.5 mm thick plain sheet glass ordinary quality n.exc 0.50 sqm in each pane complete all as spd and directed by engr in charge . 71 m & l for 5.5 mm thick plain sheet glass ordinary quality exc 0.50 sqm in each pane complete all as spd and directed by engr in charge . 72 repairing of aluminium window ( sliding or openable ) by taking out complete with frame and reassembling the window leaf with replacement of minor parts including rubber beads etc. and fixing the same opening to entire satisfaction of engineer in charge 73 repairing of aluminium door by taking out complete with frame and reassembling the window leaf with replacement of minor parts including rubber beads etc. and fixing the same opening to entire satisfaction of engineer in charge ( note : floor spring, hydraulic door spring shall be measured & paid seperately ) 74 dismantling old brocken floor hearth or wall tiling including cement mortar bedding ( but not backing ) and rubbish off the premices complete all as specified and directed. 75 coloured non skid ceramic tiles, of size 300mm x 300mm x 6 7mm thick, in floor etc. set and jointed in neat cement slurry @ 3 kg per square metre and pointed in white or coloured cement to match, over 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. 76 m&l non skid coloured ceramic tiles of first quality jointless 400mmx400mmx7mm thick as in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces complete all as specified and directed. 77 m&l for 15mm thick screed bed in cement mortar 1:6 , complete all as specified and directed 78 m&l, glazed ceramic coloured tiles of size 300 x 200 x 6 to7mm thick as in walls etc set and jointed in neat cement slurry and pointed in colour cement to match the tiles complete all as specified and directed by eic. 79 material and labour for preparation of new plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified & directed. 80 m&l for wall care putty 3 mm thick on wall after preparation of old surfaces complete all as specified & directed. 81 coloured glazed ceramic tiles of in verticle surface of size 300mm x 450mmx7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed. 82 s & f ms curtains rod of pvc coated 20 mm dia fancy type with fixing including bracket etc complete all as spd and directed by engr in charge...

Bharat Sanchar Nigam Limited - Jharkhand

20749272 tender for repairing of aluminium door shutter at chas te & tenughat bts, providing and fixing water meter at sector 12 & sector 02, steel gate for store room at sector 8 & at kasmar te, replacement of damage fiberglass plastic sheet roofing in balcony, steel window & door shtter for block 01 at sector v at bokaro (ssa dhanbad)...

Jawahar Navodaya Vidyalaya - Jharkhand

20457027 supply o hardware/m&r items 1. w.srew ½” 2. w.srew 1” 3. w.srew 1¼ 4. w.srew 1½ 5. w.srew 2” 6. w.srew 3” 7. nail ½” 8. nail 1” 9. nail ¼ 10. nail 1½ 11. nail 2” 12. nail 3” 13. china nail ½” 14. china nail 1” 15. china nail 2” 16. china nail 2½” 17. nail no. 17 18. paint brush 4” 19. paint brush 2” 20. paint brush 1½” 21. paint brush 1” 22. enamel paint 1 dram 20 ltrs. ( asian,barger,nerolac ) 23. enamel paint 20 ltrs. ( asian,barger,nerolac ) 24. distempar 20 kg.(01 dram). ( asian, barger,nerolac ) 25. colour distempar 20 kg. 1 dram. ( asian,barger,nerolac ) 26. lime 10 /20 kg bag. 27. nil blue 10 kg. bag. 28. appex(weather coat) aee 20 kg. drum. 29. nalyan rope per kg. 30. patuwa per kg. 31. snow cem branded tata 32. cement acc/ lafarge 33. narial brush 34. tar brush 35. patti 36. wall primer 37. wall putty. 38. wooden beat 39. 1 ¼” flush door (30 mm) 40. kabza 4”, 5”, 6” 41. aldrop 8”,10”, 12” company set. 42. door handele 43. tower bolt 8”, 10”, 12” 44. door lock (ring kadi). 45. plaster of paris. 46. wood primer. 47. iron primer 48. window glass(flat glass) per sqft. 49. pin head glass per sqft. 50. glass pin. 51. glass putty 52. steel wooden kabza 53. steel window handle 54. steel window stopper 55. door stopper (wooden door) 56. ddl (burger, asian, nerolac) 57. primer white 20 ltr (asian, berger, nerolac) 58. primer color 20 ltrs(asian, berger, nerolac) 59. enamel paint 01 ltr ( 60. enamel paint 01 ltrs. ( asian,barger,nerolac ) 61. distempar 01 ltr 62. colour distempar 01 ltr 63. wall primer 01 ltr 64. metal primer 01 ltr 65. wood primer 01 ltr 66. whethercoat apex ivory color 01 ltr teracota red...

Central Public Works Department - Jharkhand

16697099 tender for annual repair and maintenance of of residential building of dgms at dhanbad sh providing and fixing steel window flush door in type iii and type iv quarters and internal finishing of type iv new and external finishing of boundary wall near 5x quarters of dgms at dhanbad=> short tender notice...

Indian Institute Of Technology - Jharkhand

13937530 tender for repair work at laboratory mech engineering department ( 2w’ floor ) taking out thc old glazed steel window by cutting the hinges at 3fh floor level with nocsaty scaftolding, taking out the old glazing from steel glazed window with nccsaiy scaffolding, repair zd re fixing the steel glazed window size approx ( .45 x 1.35) mlr with fixing of m.s. revolving hinge at 3”’ floor level with tcmporaiy scaffolding and welding hinge,etc....

Council Of Scientific And Industrial Research - Jharkhand

13267703 supply of items 1. m.s aldrop 12” x ½” with nut & bolt 2. m.s tower bolt 8” bright chrome 3. m.s tower bolt 6” bright chrome 4. stainless steel hinge 4” 5. stainless steel hinge 3” 6. stainless steel hinge cut 3” 7. stainless steel hinge 2” 8. m.s hasp & staple 4” 9. stainless steel door handle 6” 10. m.s window stay ( heavy ) 11” with screw 11. m.s door stopper 12. steel window handle, right side 13. steel window handle, left side 14. m.s nail 2” 15. m.s nail 1 ½” 16. m.s nail 1” 17. m.s nail3” 18. m.s nail4” 19. pvc gitty 1 ½” 20. panel pin ( no.17 ) 1” 21. panel pin ( no.17 ) ¾” 22. panel pin ( no.20 ) ¾” 23. s.s wood screw ½” s.s wood screw ¾” 25. s.s wood screw 1” 26. s.s wood screw 1 ½” 27. s.s wood screw 2” 28. s.s wood screw 1 ¼” 29. s.s wood screw 3” 30. metal screw 2”...

Bharat Coking Coal Limited - Jharkhand

10448374 construction/ maintenance of buildings, repair of steel windows, flash door, pvc, etc. and convert a room to ladies toilet at area office, wwz, mahuda...

Department Of Posts - Jharkhand

9332743 water proofing treatment for roof, repairing of rcc chajjes back side replacement of steel windows at hpo deoghar 4th call...

Bharat Coking Coal Limited - Jharkhand

4755035 heightening of compound wall providing shed changing of steel window work etc. miscellaneous works at sub station building budhani hatia bhuli bccl...