40970010
tender for construction of road from dulhi bazaar to kajarma bhuiya toli. ( l 2.900km. ) ; 1 clearing grass and removal of rubbish up to a distance of 30 m outside the periphery of the area as per technical specification clause 201 2 compacting original ground supporting subgrade ( loosening of the ground upto a level of500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300 2 for subgrade construction. ) 3 construction of subgrade and earthen shoulders ( construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table no. 300 2 ) 4 excavation in soil using hydraulic excavator ck 90 and tippers with disposal upto 1000 metres. ( excavation for roadwork in soil with hydraulic excavator of0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m ) including royalty etc@ rs. 27.48 per cum but excluding thecost of watering, rolling & compaction. 5 construction of embankment with material deposited from roadway cutting ( construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300 2 ) rolling with smooth wheeled roller 6 granular sub base with coarse graded material ( table: 400 1 ) construction of granular sub base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at omc, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.with grading i material 7 providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at omc in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. 8 prime coat ( providing and applying primer coat with ss1 grade bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.70 kg / sqm using mechanical means. ) 9 tack coat on granular surfaces treated with primerproviding and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared granular surface cleaned with mechanical broom. 10 tack coat on bituminous surfacesproviding and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. 11 bituminous macadam ( providing and laying bituminous macadam with higher capacity hot mix plant using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction. ) 12 semi dense bituminous concrete ( providing and laying semi dense bituminous concrete with 100 120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5per centof mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects. ) for grading ii ( 10 mm nominal size ) 13 construction of dry lean cement concrete sub base over a prepared sub grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600 1, cement content not to be less than 150 kg / cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8 10 tonnes vibratory roller, finishing and curing. 14 construction ofun reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 ( grade ) , coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork ( steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing ) , spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14 days using curing compound ( where specified ) and water finishing to lines and grade as per drawingand technical specification clause 1501 15 kilometre stone ( reinforced cement concrete m15grade kilometre stone of standard design as per irc:8 1980, fixing in position including painting and printing etc ) ordinary kilometre stone ( precast ) 16 retro reflectorised traffic signs ( providing and fixing of retro reflectorised cautionary, mandatory and informatory sign as per irc :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing ) 17 direction and place identification signs with size more than 0.9 sqm size board ( providing and erecting direction and place identification retro reflectorised sign asper irc :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing ) 18 providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes. 19 earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. 20 construction of dry rubble flooring at cross drainage works for relatively less important works. 21 plain / reinfocedcement concrete in open foundation complete as per drwaing and technical specifications. ( p.c.c. grade m 15 ) 22 stone masonry work in cement mortar 1:3 in foundation complete as per drawing and technical specifications.random rubble masonry work in cement mortar 1:3 in foundation 23 stone masonry work in cement mortar 1:3 for substructure complete as per drawing and technical specificationsrandom rubble masonry work in cement mortar 1:3 in s / s 24 stone masonry work in cement mortar 1:3 in foundation complete as per drawing and technical specifications.square rubble coursed rubble masonry ( 1st sort ) in c.m. ( 1:3 ) 25 stone masonry work in cement mortar 1:3 for substructure complete as per drawing and technical specificationscoarse rubble masonary in c.m. ( 1:3 ) in sub structure 26 plain / reinforced cement concretein sub strucutre complete as per drawing and technical speciofications ( p.c.c. grade m 15 ) 27 plain / reinforced cement concretein sub strucutre complete as per drawing and technical speciofications ( p.c.c. grade m 20 in cover slab ) 28 plain / reinforced cement concretein sub strucutre complete as per drawing and technical speciofications ( p.c.c. grade m 25 in deck slab ) 29 providing and laying cement concrete wearing coat m 30 grade including reinforcement complete as per drawing and technical specifications 30 supplying, fitting and placing hysd bar reinforcement in sub structure complete as per drawing and technical specifications 31 pointing with cement mortar ( 1:3 ) on brick work in substrucutre as per technical specifications 32 plastering with cement mortar ( 1:3 ) on brick work in substructure as per technical specifications 33 providing weep holes in brick masonry / plain / reinforced concrete abutment , wing wall / returen wall with 100 mm dia ac pipe, extending through the full width of the structure with slope of 1v:20 h towards drawing face. complete as per drawing and technical specifications. 34 backfilling behind abutment, wing wall and return wall with sandy material complete as per drawings & technical specification clause 1204.3.8 ( with sandy material ) 35 laying reinforced cement concrete pipe np4 / prestressed concrete pipe for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets . 36 goods & service tax ( g.s.t. ) 37 labour cess ...
Due Date : December 19, 2023
Tender Value : ₹ 2.97 Crore
